TECHNOSOFT MOTION CONTROL BC90100 Intelligent Drives Module

وضاحتون

• Product: BC90100 Module
• Function: Heatsink and Chopping Resistor Sizing Guide
• Application: Braking module for thermal and electrical performance under braking scenarios
• Protection Mechanisms: Thermal and operating limits
• Thermal Protection: None built-in

درخواست جي وضاحت

This application note provides guidelines for selecting and dimensioning the chopping resistor and additional heatsink for the BC90100 BX braking module, ensuring reliable thermal and electrical performance under various braking scenarios.

About BC90100 BX

• The BC90100 BX unit does not apply PWM to the chopping resistor.
• When the DC bus voltage overvol کان وڌي ٿوtage threshold, the drive sends an “ON” signal to the BC90100 B module. This connects the chopping resistor directly across the DC bus.
• Once the DC bus voltage drops below the overvoltage limit, the drive sends an “OFF” signal to disconnect the chopping resistor.

BC90100 BX – Protection Features and Thermal Guidelines

Current Protection Mechanisms:

• Fast Short-Circuit Protection:
  • Triggered when the chopping current exceeds 240 A.
  • جواب ڏيڻ جو وقت: 4 μs.
• Slow Short-Circuit Protection:
  • Activated when current is between 105 A and 240 A.
  • جواب ڏيڻ جو وقت: تقريبن 1 سيڪنڊ.
• Automatic Reset (Hiccup Mode):
  • The short-circuit protection resets after 2 seconds.
  • If the fault persists, the unit re-enters protection mode cyclically.

Thermal and Operating Limits

• The BC90100 BX unit can sustain 35 A continuously at ambient temperatures up to 40°C, without additional heatsinking.
• For higher continuous currents, an external heatsink is required.
• During operation without external heatsink, keep the baseplate temperature below 75°C.
• The BC90100 BX has no built-in thermal protection.

برقي خاصيتون:

Internal Equivalent Resistance: 4.5 ايم او

Chopping Resistor Dimensioning

Known values

• VMOT - نامياري جلدtage of the DC motor bus
• آئي بي آر – Maximum regenerative current that the drives can feed back into the system during braking, under worst-case conditions.
  نوٽ: For a safe and conservative design, assume IBR equals the drive’s declared current limit. In worst-case braking, the drive limits current to the value set as Current Limit in EasyMotion Studio (under Protection and Limits → Drive Operation Parameters).
• ICR – Desired current through the chopping resistor

نوٽ: We recommend ICR = 1.1 × IBR to ensure proper energy dissipation

Calculating the Chopping Resistor Value (RCR)

Theoretical Calculation
Use Ohm’s law to determine the ideal resistor value: RCR = VMOT / ICR

Exampاليزي:

• VMOT = 48 V
• IBR = 10 A → ICR = 1.1 × 10 A = 11 A
• RCR = 48 V / 11 A = 4.36 Ω

Selecting a Realistic Resistor Value
Choose the nearest lower standard resistor value to the theoretical result.

Exampاليزي:

• Closest lower standard resistor: RCR(real) = 3.9 Ω
• Resulting current: ICR(real) = VMOT / R CR(real) = 48 V / 3.9 Ω = 12.3 A

Determining Chopping Resistor Power Requirements
Braking behavior depends on the application type and load dynamics. Evaluate resistor power based on either continuous or intermittent braking:

Continuous Braking (e.g., Gravitational Loads)

• For long-duration braking, treat the resistor’s power rating as its nominal power (PNOM):
• Power dissipated: PCR = ICR(real)² × RCR(real)

Exampاليزي:

• PCR = 12.32 × 3.9 = 590.8 W
• Choose a resistor where PCR < PNOM
• A suitable option: 3.9 Ω rated at 800 W

Short-Duration Braking (Intermittent Use)
For short braking bursts, you can use a resistor’s overload power (POL), as specified by the manufacturer:

• پول = k × PNOM
• يقيني بڻائڻ: PCR < POL

You must also respect average power limits for repeated braking cycles:

• tBR = Braking time
• TBR = Minimum interval between braking events
• PCR(avg) = PCR × (tBR / TBR)
• Final condition: PCR(avg) < PNOM

Exampاليزي:

• tBR = 5 s
• Resistor: RS150 (150 W nominal), with k = 5
• POL = 5 × 150 W = 750 W
• PCR = 590.8 W < 750 W

Now calculate the minimum TBR:

• 150 W = (590.8 W × 5 s) / TBR → TBR ≥ 19.7 s
• This setup allows braking for 5 seconds every 20 seconds using a 150 W nominal chopping resistor.

طول و عرض

Dimensioning the Thermal Resistivity of the Heatsink for BC90100 BX (if required)

Known Values

• RSW – Equivalent resistance of the internal chopping switch in the BC90100 BX: RSW = 4.5 mΩ
• TSW – Maximum allowable temperature of the switch case:
• TSW = 100°C

Calculating the Required Thermal Resistivity for an Additional Heatsink

Theoretical Cooling Model
The heat transfer model is analogous to Ohm’s Law:

• جلدtage → Temperature difference
• Current → Thermal power
• Resistance → Thermal resistivity

Term definitions in the model:

• ٽي او ايس – Temperature of the BC90100 BX switch (must remain below 100°C)
• THS – Temperature at the baseplate of the BC90100 BX
• تامب - ماحول جي درجه حرارت
• پي ايس ڊبليو – Power dissipated in the internal switch
• RthSW – Internal thermal resistance between the switch and baseplate:
• RthSW = 0.8°C/W
• RthHS – Thermal resistivity of the additional heatsink (this is the value to be determined)

Calculating Power Dissipated by the Switch

فارمولا:
PSW = ICR(real) × ICR(real) × RSW

Exampاليزي:

• For ICR(real) = 100 A:
• PSW = 100 A × 100 A × 4.5 mΩ = 45 W

Calculating Required Thermal Resistivity of the Additional Heatsink

فارمولا:

• RthHS = (TSW – Tamb) / PSW – RthSW
• This gives the maximum allowed thermal resistivity of the additional heatsink.

Exampاليزي:

• ICR(real) = 100 A
• ٽمب = 40 ° سي
• PSW = 45 W
• TSW = 100°C
• RthSW = 0.8°C/W
  • RthHS = (100°C – 40°C) / 45 W – 0.8°C/W
  • RthHS = 60°C / 45 W – 0.8°C/W = 1.33 – 0.8 = 0.53°C/W

هن ۾ اڳوڻيample, the additional heatsink must have a thermal resistivity of 0.53°C/W or lower.

FAQ

Is thermal protection built-in for the BC90100 BX?

No, the BC90100 BX does not have built-in thermal protection.

How to select a realistic resistor value for chopping?

Choose the nearest lower standard resistor value to the theoretical result obtained using Ohm's law.

دستاويز / وسيلا

TECHNOSOFT MOTION CONTROL BC90100 Intelligent Drives Module [pdf] استعمال ڪندڙ ھدايت BC90100 Intelligent Drives Module, BC90100, Intelligent Drives Module, Drives Module, Module

حوالو

• استعمال ڪندڙ دستي