dalap NOMIA Timer and Humidity Sensor
وضاحتون
- Product Name: Dalap NOMIA household axial fan
- Intended Use: Small and medium-sized residential and non-residential units
- Function: Continuous ventilation
حفاظت جي گهرج
صرف پنن تي سار سنڀال کي انجام ڏيو جڏهن مينز کان ڌار ٿي وڃي! سال ۾ گهٽ ۾ گهٽ هڪ ڀيرو سار سنڀال. پرستار کي هٽائڻ کان پوء، ان کي نرم رگ سان صاف ڪريو ڊيampened with a mild solution of water and detergent. Be careful not to wet down the electrical parts of the fan, especially the motor. Wipe the fan dry and return it to its installed position.
مشڪلاتون
| غلطي | ممڪن سبب | علاج |
|---|---|---|
| The fan does not rotate or respond to control | بجلي جي فراهمي سان ڳنڍيل ناهي | پاور سپلائي ڪنيڪشن چيڪ ڪريو |
| Increased noise or vibration | Internal joint fault or a clogged ventilation system | Call a specialist for internal joints or clean ventilation سسٽم |
پيداوار جي ٺاھ جوڙ
Connecting NOMIA (models without timer and humidistat)
- Switch off the electric circuit.
- Unscrew the screw on the front panel’s side to access the terminal block.
- Run supply cables through the rubber bushing and connect them in the terminal block.
- Connect the electric circuit and test the function of the fan after installation.
Configuring Fan Algorithms with Option ZW
Section 1. Configuring the Built-In Humidity Sensor
Set the humidity values (50%, 70%, 90%) or disable the sensor. In IN mode, the fan turns on/off with the lights. In OUT mode, it operates independently based on timer settings.
Section 2. Setting the Switch-Off Delay Time
Adjust fan operation time after lights out (5, 15, 30 min) or disable the timer.
Section 3. Setting the Ventilation Mode
Set ventilation intervals (6, 12, 24 hours) or disable ventilation.
Section 4. Setting the Integrated Light Sensor
Details on connection and configuration can be found in the user manual.
USES
- The Dalap NOMIA household axial fan is intended for use in small and medium-sized residential and non-residential units.
- مداحن کي مسلسل وائيٽليشن لاء استعمال ڪري سگهجي ٿو.
حفاظت جي گهرج
- مھرباني ڪري ھن دستياب کي احتياط سان پڙھو ۽ استعمال ڪرڻ کان پھريان سڀني ضرورتن تي ڌيان ڏيو.
- اهو منع ٿيل آهي ته فين کي ڊڪٽنگ سسٽم ۾ نصب ڪرڻ لاء جيڪي فلو گيس کي هلائڻ لاء استعمال ڪيا ويندا آهن.
- The installation, connection, and maintenance of the fan may only be done when the fan is disconnected from the mains.
- ٽائمر ۽ humidistat صرف ان کان پوء سيٽ ڪري سگهجي ٿو جڏهن پرستار مينز کان ڌار ٿيڻ کان پوء.
- ٻئي ڪنيڪشن ۽ سپلائي نيٽ ورڪ کان ڪنيڪشن صرف هڪ ماهر اليڪٽريشن طرفان ٿيڻ گهرجي.
- This device is not intended for use by persons (including children) with reduced physical, sensory, or mental abilities or r lack of experience and knowledge, if they are not supervised or the person responsible for their safety has not provided them with the instructions for use.
- The fan is designed for connection to a single-phase alternating current of 220–240 V with a frequency of 50 Hz.
- تحفظ جو درجو IP25 آهي. آپريٽنگ گرمي پد +1 کان +40 ° سي.
سار سنڀال
صرف پنن تي سار سنڀال کي انجام ڏيو جڏهن مينز کان ڌار ٿي وڃي! سال ۾ گهٽ ۾ گهٽ هڪ ڀيرو سار سنڀال. پرستار کي هٽائڻ کان پوء، ان کي نرم رگ سان صاف ڪريو ڊيampened with a mild solution of water and detergent. Be careful not to wet down the electrical parts of the fan, especially the motor. Wipe the fan dry and return it to its installed position.
مسئلو حل ڪرڻ
| غلطي | ممڪن سبب | علاج |
| After being connected to the power supply, the fan does not rotate or respond to control in any way. | بجلي جي فراهمي سان ڳنڍيل ناهي. |
هڪ ماهر کي سڏ. |
| ڊوائيس جي اندروني جوڑوں ۾ هڪ غلطي آهي. | ||
| هوا جو وهڪرو گهٽ آهي. | وينٽيليشن سسٽم بند آهي. | وينٽيليشن سسٽم کي صاف ڪريو. |
|
وڌيل شور يا وائبريشن. |
فين صحيح طرح سان ڳنڍيل نه آهي يا غلط نصب ٿيل آهي. | انسٽاليشن دوران غلطي کي هٽايو. |
| وينٽيليشن سسٽم بند آهي. | وينٽيليشن سسٽم کي صاف ڪريو. |
NOMIA (ماڊل بغير ٽائمر ۽ humidistat)
ڪنيڪشن
- Switch off ffthe electric circuit that you are going to work on.
- فرنٽ پينل جي پاسي واري اسڪرو کي کوليو ۽ ان ڍڪ کي هٽايو جنھن جي ھيٺان ٽرمينل بلاڪ ٻن ٽرمينلز سان واقع آھي.
- سپلائي ڪيبلز (مستقل مرحلو ۽ غير جانبدار) کي ربر بشنگ ذريعي هلايو ۽ انهن کي ٽرمينل بلاڪ ۾ ڳنڍيو. ڪيبل ڪنيڪشن جي پوزيشن هن معاملي ۾ ڪا به اهميت نه آهي.
- انسٽاليشن مڪمل ڪرڻ کان پوء، برقي سرڪٽ سان ڳنڍيو ۽ فين جي فنڪشن کي جانچيو.
ڪنٽرول عناصر
- The fan is connected by three wires to terminals “L”, “TLH and
- ٽائمر کي خارجي سوئچ ذريعي ڪنٽرول ڪيو ويندو آهي.
- پرستار کي چالو ڪيو ويندو آهي جڏهن سوئچ کي ڦيرايو ويندو آهي ۽ هلندو آهي جيستائين اهو آن آهي.
- جڏهن ٻاهرين سوئچ کي بند ڪيو ويندو آهي، فين ٽائمر تي مقرر ڪيل وقت تائين هلندو ۽ خودڪار طور تي بند ٿي ويندو.
- ٽائمر کي اليڪٽرانڪس تي "TIME" potentiometer طرفان مقرر ڪيو ويو آهي:
-
- In the leftmost position, the timer is switched off
- In the rightmost position, the timer time is 30 minutes.
- ترتيب ڏيڻ لاء هڪ ننڍڙو اسڪوائر استعمال ڪريو.
Connecting and configuring fan algorithms with option ZW
ڪنٽرول
‘Bwd images and component locations may vary
وائرنگ تصوير
- The is connected with two wires to terminals and “L” (it is recommended to use polarity, so the board will work more efficiently and the fan operates in automatic mode.
آپريشن جا طريقا
- ! The default setting at the factory is the typical automatic mode of operation.
The fan will turn on when the built-in humidity sensor detects humidity above 70% (SECTION 1) and will run until the humidity sensor detects a decrease to 70% or below (SECTION M). The fan will then run for 15 minutes (SECTION 2) and turn off. Every 12 hours (SECTION’) the fan will turn on and then turn off after 30 minutes. If the fan is installed in a room with permanently low or permanently high humidity levels, it is recommended to disable the built-in humidity sensor (SECTION 1). For convenience, it is possible to set the fan to turn on only when there are no people in the room (determined by the absence of lighting). To do this, turn the MODE switch to the “OUT” position.
The fan will switch on when the humidity sensor detects that the humidity exceeds (SECTION 1), but only if the built-in light sensor (SECTION A) detects that there is no light in the room, and will run until the humidity sensor detects that the humidity drops to 70% or below (SECTION 5). The fan will then run for 15 minutes(SECTION 2) and turn 0m. Every 12 hours (SECTIONC3), the fan will turn on and then turn off after 30 minutes.
If a light comes on in the room while the fan is operating, it will stop operating immediately.
ڪنيڪشن ۽ ڪنفيگريشن
اهم: All operations related to connection, adjustment, maintenance, and repair of the product should be performed only when the mains voltage is removed. And repair of the product should be carried out only when the mains voltage is disconnected (circuit breaker S1 in OFF position).
- Regardless of the wiring diagram, the unit only operates when the circuit breaker S1 is closed. The fan can only be energized,
- i.e., the circuit breaker S1 can only be energized when the front panel of the fan is closed.
- To prevent the switches from malfunctioning, do not apply excessive force when setting.
SECTION 1. CONFIGURING THE BUILT-IN HUMIDITY SENSOR
The factory default humidity at which the fan switches on automatically is set to 70%. If required, the following humidity values can be selected: 50, 70, 90%. Or you can disable the built-in humidity sensor altogether. To do this, set the Humidity switch to the required value.
If the humidity sensor is disabled, the fan in IN mode will turn on when the lights are turned on and will run until the lights are turned off, and after they are turned off for the time set on the Timer switch. In OUT mode, the fan will turn on when the lights are turned off and will run for the time set on the Timer switch.
SECTION 2. SETTING THE SWITCH-OFF DELAY TIME
The factory default fan operation time after lights out is 1 minute. If necessary, you can set the fan operation time after lights out to 5, 15, or 30 minutes. Or disable the timer altogether. To do this, set the Timer switch to the required value.
SECTION 3. SETTING THE VENTILATION MODE
The factory default setting is 12 hours, after which the fan is switched on in ventilation mode and runs for 30 minutes, after which it is switched off. If necessary, it is possible to set the ventilation intervals: 6, 12, or 24 hours. Or disable ventilation altogether. To do this, set the Airing switch to the required value.
SECTION 4. SETTING THE INTEGRATED LIGHT SENSOR
The factory default light sensor sensitivity is set to medium (default 70%). If necessary, you can select light values of 50, 70, or 90%. Or disable the built-in light sensor altogether. It is recommended to reduce the sensitivity of the light sensor to 50% (e.g., for a room with a window) or increase its sensitivity to 90% (e.g, for a room with low light). To do this, set the Light switch to the desired value.
Distributor for the EU,
- DALAP GmbH
- ٽوفرگاس 72
- 095 26 Olbernhau، DE
- www.dalap.eu
- info@dalap.eu
وارنٽي سرٽيفڪيٽ
- NOMIA 100
- NOMIA 125
- NOMIA 100 Z
- NOMIA 125 Z
- NOMIA 100 ZW
- NOMIA 125 ZW
وڪرو ڪندڙ سينٽamp,
Date of Sale,————-
اليڪٽرانڪ ۽ برقي سامان جو چونڊيل مجموعو.
غير ترتيب ڏنل ميونسپل فضول ۾ اليڪٽرانڪ ۽ برقي شين جي ضايع ڪرڻ منع آهي.
FAQs
Q: How often should maintenance be performed on the fan?
A: Maintenance should be conducted at least once a year when the fan is disconnected from the mains.
Q: What should I do if the fan does not rotate or respond to control?
A: Check if the power supply is connected and if not, rectify the connection.
دستاويز / وسيلا
 |
dalap NOMIA Timer and Humidity Sensor [pdf] استعمال ڪندڙ دستياب NOMIA Timer and Humidity Sensor, NOMIA, Timer and Humidity Sensor, Humidity Sensor, Sensor |