Schlage Encode logo

Schlage Encode Smart Deadbolt

Quick Start Guide

Schlage Encode Smart Deadbolt - Parts

SCHLAGE

App - Symbol Start here!

schlage.com/encode-workswith

Visit schlage.com/encode-workswith  to setup and control your Schlage Custom logo with your smartphone.

Touchscreen

Cord Zero WifiCommunication Icon

      • Flashes when lock is connecting to WiFi to check for updates.

Low Battery - Symbol Low Battery Icon

      • Flashes after code is entered when battery is low.
      • Solid when battery is critical. The lock will not work without new batteries.

Schlage Encode Smart Deadbolt - Touchscreen

Programming and Input - SymbolProgramming and Input LED

      • Flashes white on every digit that is entered.
      • Amber when using manual programming mode.

Home Button - SymbolHome Button and Checkmark Icon

      • Turns on keypad backlight.
      • Starts WiFi connection process.
      • Checkmark flashes when code entry is correct.
      • Checkmark flashes when manual programming are successful.

Lock Button - SymbolLock Button and “X” Icon

      • Locks the lock.
      • Turns on keypad backlight if the lock is locked.
      • “X” flashes for a wrong user code.

Tools

Schlage Encode Smart Deadbolt - Tools

Phillips screwdriver Don’t use a power drill!

Step 1

Remove existing lock.

Remove the entire deadbolt, including the bolt. You may also want to remove the strike. A standard Schlage deadbolt is shown. Check with your specific deadbolt manufacturer if you need help.

Schlage Encode Smart Deadbolt - Remove existing lock

Step 2

Need Help?

Visit schlage.com/faqs-encode

Install the bolt.

You may have to adjust your bolt length. Make sure the slot in the bolt is centered in the hole.

Schlage Encode Smart Deadbolt - Install the bolt

Step 3

Need Help?

Trouble installing the strike reinforcer?
Visit schlage.com/faqs-encode and follow interactive instructions.

Install the strike into the door frame.

If you have a window next to your door, you may not be able to use the longer wood screws to install the reinforcer.

Schlage Encode Smart Deadbolt - Install the strike into the door frame

Step 4

Is it hard to install the touchscreen?
Is the tailpiece not installing correctly?
If your through-hole seems too small, you may need to remove the spacer. Visit schlage.com/faqs-encode.

Install the touchscreen.

Route the cable through the door BELOW the bolt. Align the tailpiece as shown and push the touchscreen onto the door.

Schlage Encode Smart Deadbolt - Install the touchscreen

Step 5

Schlage Encode Smart Deadbolt - Tools

Phillips screwdriver Don’t use a power drill! You may damage your lock!

Install the backplate.

Route the cable under the bolt and through the hole on the bottom of the backplate. Secure the backplate with screws. Make sure the outside touchscreen is straight before tightening screws all the way.

Schlage Encode Smart Deadbolt - Install the backplate

 

Step 6

Connect the cable.

Tuck the cable and connector in the space above the spindle.

Schlage Encode Smart Deadbolt - Connect the cable

Step 7

Schlage Encode Smart Deadbolt - Tools

Phillips screwdriver Don’t use a power drill! You may damage your lock!

Secure the lock to the door.

If the bump on the tailpiece doesn’t align with the slot in the back of the inside assembly, make sure your thumbturn is vertical (up and down).

Schlage Encode Smart Deadbolt - Secure the lock to the door

Step 8

Install batteries and slide the cover on.

Schlage Encode Smart Deadbolt - Install batteries and slide the cover on

That wasn’t so bad, was it?

Your lock is now installed! Remember, you still have to set up your lock to use it.

Step 9

Schlage Encode Smart Deadbolt - Set up your lock

Set up your lock.

1. Open your door!
2. Enter one of the two default user codes.
3. Your lock will enter a setup routine. When the bolt stops moving, setup is complete.

Final test!

1. Close your door.
2. Extend and retract the bolt using the inside thumbturn.
3. Make sure the bolt retracts smoothly.
4. Open your door.
5. Extend the bolt using the inside thumbturn.
6. Now enter a user code at the touchscreen.

Need Help?
If the bolt doesn’t extend or retract during testing,visit schlage.com/faqs-encode.

SCHLAGE

Now that your lock is installed

you can use a smart home system to lock and unlock your door from anywhere and add user codes for guests and household members.

schlage.com/encode-workswith

Visit schlage.com/encode-workswith for a list of compatible smart home apps that allow you to control your Schlage Custom logowith your smartphone.

Lock and unlock

To lock your door just tap the lock icon.

You can also lock your door from inside by turning the thumb turn toward the door edge.

Schlage Encode Smart Deadbolt - Lock and unlock

To unlock your door enter a user code.

You can also unlock your door from inside by turning the thumb turn away from the door edge.

Schlage Encode Smart Deadbolt - To unlock your door

 

Questions about your new
Schlage Custom logoSmart WiFi Deadbolt?

Please don’t return it to the store!

Let us help you first!

App - Symbol

www.schlage.com/faqs-encode

 

Allegion

© Allegion 2018
Printed in U.S.A.
P518-415 Rev. 08/18-d

 

Schlage Encode Smart Deadbolt User Manual – Optimized PDF
Schlage Encode Smart Deadbolt User Manual – Original PDF

Join the Conversation

2 Comments

  1. My Encode model number BE489WB was missing the inside assembly screws. I don’t mind going out and getting two but I do not know what size to get. The Lowes employee thought they might be #8’s and I bought some, but they did not fit. Can you tell me what size to get?

  2. I am not able to proceed further to step 4 to programme the lock. I have inputted the programming code, press the button as directed, get a red light blinking, beep and then a blue light and beep and then a message saying unable to locate the device. I have tried so many times. Please advise.

Leave a comment

Your email address will not be published.