SAGE logoUltrathin Touch Slide RF Remote Controller
Model No.: R11,R12,R13
Touch color slide/1-3 color/Wireless remote 30m distance/CR2032 battery/Magnet stuck fixSAGE LU MEI R11 Ultrathin Touch Slide RF Remote ControllerSAGE LU MEI R11 Ultrathin Touch Slide RF Remote Controller - icon

Features

  • Apply to a single color, dual color or RGB LED controller.
  • Ultra-sensitive color adjustment touch slide.
  • Each remote can match one or more receivers.
  •  CR2032 battery-powered.
  • Operate with LED indicator light.
  • Magnet on the back which can be easily stuck on back holder or any metal surfaces.

Technical Parameters

Input and Output
Output signal RF 2.4GHz
Working voltage 3VDC CR2032
Working current <5mA
Standby current <10μA
Standby time 1 year
Remote distance 30m(Barrier-free space)
Environment
Operation temperature Ta: -30 O C ~ +55 O C
IP rating IP20
Safety and EMC
EMC standard (EMC) ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Safety standard(LVD) EN 62368-1:2020+A11:2020
Radio Equipment(RED) ETSI EN 300 328 V2.2.2
Certification CE,EMC,LVD,RED
Warranty
  Warranty  5 years
Weight
Gross weight 24g
  Net weight  64g

Mechanical Structures and Installations

SAGE LU MEI R11 Ultrathin Touch Slide RF Remote Controller - remote

To fix the remote, three options are offered for selection:
Option 1: stuck the remote on any metal surfaces directly.
Option 2: fix the remote’ back holder on the wall with two screws.
Option 3: adhere the remote’ back holder to the wall with a paster.

Match Remote Control (two match ways)

The end users can choose suitable match/delete ways. Two options are offered for selection:

Use the controller’s Match key
Match: Short press the match key, and immediately press on/off key on the remote.
The LED indicator fast flash a few times means the match is successful.
Delete: Press and hold the match key for 5s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted.
Use Power Restart
Match: Switch off the power, then switch on the power, repeat again. An immediately short press on/off key 3 times on the remote. The light blinks 3 times means the match is successful.
Delete: Switch off the power, then switch on the power, repeat again. An immediately short press on/off key 5 times on the remote. The light blinks 5 times means all matched remotes were deleted.

Key function

  • R11 1 zone dimming remote SAGE LU MEI R11 Ultrathin Touch Slide RF Remote Controller - fig
  • R12 1 zone CCT remoteSAGE LU MEI R11 Ultrathin Touch Slide RF Remote Controller - e CCT remote
  • R13 1 zone RGB remoteSAGE LU MEI R11 Ultrathin Touch Slide RF Remote Controller - RGB remote

Safety information

  1. Read all instructions carefully before you begin this installation.
  2. When installing the battery, pay attention to the battery’s positive and negative polarity.
    After a long time without the remote control, remove the battery.
    When remote distance becomes smaller and insensitive, replace the battery.
  3. If no response from the receiver, please re-match the remote.
  4. Gently handle the remote, beware of falling.
  5.  For indoor and dry location use only.

Documents / Resources

SAGE LU MEI R11 Ultrathin Touch Slide RF Remote Controller [pdf] Instruction Manual
R11, R12, Ultrathin Touch Slide RF Remote Controller, Touch Slide RF Remote Controller, RF Remote Controller, Remote Controller, R11, Controller

References

Leave a comment

Your email address will not be published. Required fields are marked *