2022 Polaris RZR Pro R Apex Running Lights
POLARIS RZR PRO R 2022+
APEX LIGHTS
REAR RED
INSTRUCTION MANUAL
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
1
POLARIS RZR PRO R 2022+
APEX LIGHTS – REAR RED
Part #: 64-501 Fitment: POLARIS RZR PRO R 2022+
TOOLS NEEDED: *OPTIONAL
Side Cutter Pliers
3mm Allen Wrench
4mm Allen Wrench
Needle Nose Pliers
Heat Gun/Lighter
11/32″ drill bit*
1/4″ drill bit*
PARTS INCLUDED:
· Apex Light (2x) · Power Harness (2x) · Extension Harness (2x) · Roll Bar Adapter (2x) · Strap (2x) · Zip Tie (8x) · Double Sided Tape (2x) · Pulse Modulator (2x) · Taillight Harness (2x)
Drill*
· M6 Flat Washer (2x) · M5 x 0.8 x 6mm Allen Screw (4x) · M6 x 1.0 x 10mm Allen Screw (2x) · Adhesive Promoter Wipe (2x) · Rubbing Alcohol Wipe (2x) · Dielectric Grease (1x) · Heat Shrink (1x)
2
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
INSTALL VIDEO TUTORIAL
DON’T LIKE INSTRUCTIONS? VISIT OUR WEBSITE TO ACCESS THE VIDEO TUTORIAL.
NOTE: Dielectric grease is provided in each kit. We’ve engineered sealed connectors but we still recommend applying a small dab of dielectric grease on each connection point for added protection.
NOTE: Make sure your vehicle is off and key is out of the ignition before starting.
1 UNPLUG TAILLIGHT
Starting from the left side, unplug the OEM connector from your RZR Pro R taillight and plug the taillight harness provided in-line. [SEE FIGURES 1A 1D]
1A
1B
1C
1D
TAILLIGHT HARNESS
TO STOCK OEM TAILLIGHT HARNESS
TO TAILLIGHT
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
3
2 HEAT SHRINK YOUR CONNECTIONS AND EXTRA CONNECTORS
As you make plug & play connections, use the heat shrink tubing, provided to protect your connections from dirt on the trails. Go over the connection points you make and cut 2″ of heat shrink for each. Use a lighter or heat gun to shrink the tubing. [SEE FIGURES 2A – 2G]
HEAT SHRINK CONNECTIONS
2A
2B
2C
2D
2E
2F
2G
For the unused extension harness connectors (mentioned in the next step) cut 1.5″ piece of heat shrink tubing, slide it over the connector and heat shrink it using a lighter or heat gun. Use needle nose pliers to pinch the end of the extra heat shrink. This will act as a cap to protect the connectors from getting dirt inside. [SEE FIGURES 2H – 2L]
HEAT SHRINK EXTRA PLUGS
2H
EXTRA PLUG
MALE CONNECTORS
EXTRA PLUG EXTENSION HARNESS (2X)
2I
2J
FEMALE CONNECTOR
MALE CONNECTOR
4
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
2K
2L
NEEDLE NOSE PLIERS
3 PLUG IN PULSE MODULATOR
Plug in your pulse modulator to the Apex Light taillight harness. [SEE FIGURE 3A]
3A
PULSE MODULATOR
APEX LIGHT TAILLIGHT HARNESS
4 PLUG IN EXTENSION HARNESS
Plug in your extension harness to the pulse modulator. [SEE FIGURES 4A] NOTE: Extension harnesses supplied come with extra connectors to easily add more Apex Lights, as seen in the circled connectors in FIGURE 4A.
4A
APEX LIGHT
EXTENSION HARNESS
HEAT SHRINK TUBING PULSE MODULATOR
APEX LIGHT TAILLIGHT HARNESS
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
5
5 SELECT LOCATIONS FOR APEX LIGHTS
Your options include: · Exterior Body Panel
Any exterior panel with 8″ of flat surface for mounting · Roof Mounting · Roll Bar/Bumper Mounting
Check out the video to the right (see QR code) for a 50 second walkthrough of the different Apex Light mounting options.
6 ROUTE WIRING
With your extension harness plugged into the taillight harness, choose your mounting location on the RZR. Route your extension harness from the brake light to your mounting location.
NOTE: We suggest you leave slack in wires until end of install when wires can be secured with wire ties provided. Route all wiring away from moving or hot components.
7 READY TO MOUNT APEX LIGHT
Once you have routed your extension harness you are now ready to mount your Apex Lights.
If you have chosen to mount your Apex Lights to a roll bar or bumper, you will follow the Roll Bar mounting steps detailed in step 7A.
If you have decided to mount your Apex Lights to either an exterior panel or to your roof, you now have to decide whether you want to mount your Apex Lights via:
a) Adhesive mount (i.e. no drill) follow step 7B
b) Drill-mount for increased security follow step 7C
6
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
7A
OPTION A – ROLL BAR MOUNTING:
OPTION A DIAGRAM – ROLL BAR MOUNTING
APEX LIGHT
ROLL BAR ADAPTOR M5 X 0.8 X 6MM ALLEN SCREW (2X) DOUBLE-SIDED TAPE
ROLL BAR
STRAP: GOES IN BETWEEN APEX LIGHT AND ROLL BAR ADAPTER
INSTALL ROLL
A
i BAR ADAPTOR
Install the roll bar adapter to the
base of the light by using two of the M5 x 0.8 x 6mm Allen
B
Screws with a 3MM ALLEN
WRENCH. [SEE FIGURES A – C]
NOTE: Select which side you would like your wire to exit the light that allows you to best hide your wires.
C
3mm Allen Wrench
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
7
ii INSTALL STRAP
Once the roll bar adapter is secured to the light, install the strap provided through the opening between the light base and the roll bar adapter. [SEE FIGURES D & E]
D
E
iii WIPE DOWN SURFACES
Before you permanently install your Apex Light to the UTV’s roll bar you’ve chosen, wipe down the roll bar and the base of the light with the rubbing alcohol wipe provided and let dry.
Next wipe down the roll bar and light base with the adhesion promoter wipe provided. Let dry. [SEE FIGURES F – J]
F
G
H
RUBBING ALCOHOL WIPE
ADHESIVE PROMOTER WIPE
I
J
8
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
iv APPLY TAPE
Apply the double-sided tape to the dry Apex Light’s roll bar adapter, and attach the light to the surface you cleaned and prepared in the prior step. [SEE FIGURES K – N]
K
L
M
N
ROLL BAR
v TIGHTEN STRAP
Tighten straps onto base and roll bar. [SEE FIGURES O & P] NOTE: If you have excess length of strap you can rotate the buckle away from the slack to reduce the slack in the strap.
O
P
JUMP TO STEPS 8-11 TO FINISH INSTALL
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
9
7B
OPTION B – ADHESIVE ONLY MOUNTING:
OPTION B DIAGRAM – ADHESIVE ONLY MOUNTING
APEX LIGHT DOUBLE-SIDED TAPE PREPPED FLAT PANEL
i LOCATE A SURFACE
A
TO MOUNT TO
Locate an exterior panel with 8″ of flat surface for mounting. [SEE FIGURE A] NOTE: If you’re adhesive mounting the Apex Lights to the roof, we recommend drilling a hole to feed the wires through. The Apex Light adhesive creates a water-tight seal.
ii WIPE DOWN SURFACES
Before you permanently install your Apex Light to the UTV’s flat panel you’ve chosen, wipe down the panel and the base of the light with the rubbing alcohol wipe provided and let dry.
Next wipe down the panel and light base with the adhesion promoter wipe provided. Let dry. [SEE FIGURES B & C]
B
C
RUBBING ALCOHOL WIPE
ADHESIVE PROMOTER WIPE
RUBBING
ADHESIVE
ALCOHOL WIPE PROMOTER WIPE
10
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
iii APPLY TAPE
Apply the double-sided tape to the Apex Light’s base and affix the light to the prepped surface. [SEE FIGURES D – G]
NOTE: Be sure the whole light’s base is in contact with the surface of the UTV to ensure the light will hold up permanently.
D
E
F
G
FLAT SURFACE
JUMP TO STEPS 8-11 TO FINISH INSTALL
7C
OPTION C – DRILLED AND ADHESIVE MOUNTING:
OPTION C DIAGRAM – DRILLED AND ADHESIVE MOUNTING
APEX LIGHT
DOUBLE-SIDED TAPE PREPPED FLAT PANEL M6 FLAT WASHER M6 X 1.0 X 10MM ALLEN SCREW
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
11
i LOCATE A SURFACE
A
TO MOUNT TO
Locate an exterior panel with 8″ of flat surface for mounting. [SEE FIGURE A FOR]
ii MARK HOLES TO DRILL
Use the double-sided tape holes as a template for the drilling locations. Confirm you can access the inside of the panel that you’ll need to be able to access this area with your flat washer. [SEE FIGURES B – D]
B
C
D
WIDE END
THIS
DIAGRAM
IS NOT A
TEMPLATE
DRILL ¼” HOLE ON PANEL DRILL 11/32″ HOLE ON PANEL
NARROW END
iii DRILL ¼” HOLE
Once you have your holes marked, drill a ¼” hole that will be used to feed the screw through.
NOTE: We recommend using a brad point drill bit to avoid damaging your panel.
iv DRILL 11/32″ HOLE
Drill a 11/32″ hole that you will feed the Apex Light’s wire connector through.
12
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
v WIPE SURFACE WITH RUBBING ALCOHOL
Before you permanently install your Apex Light to the UTV’s flat panel you’ve chosen, wipe down the panel and the base of the light with the rubbing alcohol wipe provided and let dry.
Next wipe down the panel and light base with the adhesion promoter wipe provided. Let dry. [SEE FIGURES E & F]
E
F
RUBBING ALCOHOL WIPE
ADHESIVE PROMOTER WIPE
RUBBING
ADHESIVE
ALCOHOL WIPE PROMOTER WIPE
vi APPLY TAPE
Apply the double-sided tape to the Apex Light’s base. [SEE FIGURES G – I]
G
H
I
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
13
vii ADHERE LIGHT TO PREPPED SURFACE
Feed your light’s wiring through the 11/32″ hole. Peel away the double-sided tape cover, and stick the Apex Light to the prepped surface. [SEE FIGURES J – L]
J
K
L
viii THREAD IN SCREW
Thread your M6 x 1.0 x 10mm Socket Allen Screw with an M6 Flat Washer through the backside of the panel into the light’s base using a 4MM ALLEN WRENCH. [SEE FIGURES M & N] NOTE: If a longer screw is required, you have two options: 1. Give us a call or email, and we will express mail you a screw of the length you need. 2. Go to your local hardware store and purchase a M6 x 1.0 x (your desired length).
M
N
APEX LIGHT
11/32″ DRILLED HOLE
¼” DRILLED HOLE
DOUBLE-SIDED TAPE PREPPED FLAT PANEL
M6 FLAT WASHER M6 X 1.0 X 10MM ALLEN SCREW
JUMP TO STEPS 8-11 TO FINISH INSTALL
14
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
CONTINUATION STEPS 8-11
8 PLUG IN THE APEX LIGHT
Plug your Apex Light into the extension harness. [SEE FIGURES 8A & 8B] NOTE: Remember to heat shrink all your connection points as seen in step 2.
8A
8B
9 REPEAT STEPS 1 TO 8
Repeat step 1 through 8 on the right side of the RZR to install your other Apex Light.
10 LET THE ADHESIVE CURE
Let adhesive tape cure for 24 hours before riding.
11 SECURE WIRING
Once you have both of your Apex Lights mounted, go through and secure all the wiring using the zip ties provided. NOTE: Secure wiring away from hot or moving components. NOTE: Remember to heat shrink all your connection points as seen in step 2.
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
15
WHY RAVEK
Stock UTVs don’t come with enough storage, lighting, comfort, and protection. That’s why we started RAVEK.
We live to design, manufacture, and test innovative SxS upgrades that elevate the riding experience. Here’s what you can expect from us: · Durable products built to last (100% lifetime guarantee) · UTV upgrades thoughtfully designed & tested by riders · Outstanding installation support (videos & USA customer service) · Constant flow of epic riding content (check out our social media)
We’re confident your RAVEK product will earn its place on your machine. Please call or e-mail us if we can help.
– Harry & Ricky (Brothers & Owners)
MESSAGE FROM THE DESIGNER
Has anyone ever noticed how there are far fewer light options for the rear of these vehicles than the front? The contours of the Apex Lights in red just pop to me. Not only are you adding the safety of more rearward facing taillights, but they also inevitably make anything look badass, am I right?
16
RAVEK POLARIS RZR PRO R 2022+ PLUG & PLAY APEX LIGHTS (REAR RED)
Documents / Resources
 |
RAVEK 2022 Polaris RZR Pro R Apex Running Lights [pdf] Instruction Manual 2022 Polaris RZR Pro R Apex Running Lights, 2022, Polaris RZR Pro R Apex Running Lights, Apex Running Lights, Running Lights |
