Contents
hide
Rapidline Halo Static Single Sided Fixed Height Workstation Frame Instruction Manual
Specifications
- Frame Type: Static Single Sided Fixed Height Workstation
- Frame Material: Steel
- Frame Color: Black
- Table Feet: 2 pieces
- Column: 2 pieces (1 right, 1 left)
- Bolts: M6x12 (5 pieces), M6x10 (3 pieces)
- Screws: ST4x20 (22 pieces), M6x12 (4 pieces), M5x6 (8 pieces)
- Tools Included: Allen Wrench 4mm (1 piece), Allen Wrench 5mm (1 piece), Cable Tie (5 pieces)
Component parts
| No. | Component Name | Pcs | No. | Component Name | Pcs |
|---|---|---|---|---|---|
| 1 | Table feet | 2 | 9 | Centre bracket | 1 |
| 2 | Column (right) | 1 | 10 | Center rails | 2 |
| 3 | Bolt: M6x12 | 5 | 11 | Top frame-2 | 1 |
| 4 | Screw: ST4x20 | 22 | 12 | Column (left) | 1 |
| 5 | Side brackets | 2 | 13 | Allen Wrench (4mm) | 1 |
| 6 | Rubber pad | 14 | 14 | Allen Wrench (5mm) | 1 |
| 7 | Top frame-1 | 1 | 15 | Cable Tie | 5 |
| 8 | Bolt: M6x10 | 3 |
Assembly Instructions
- Step 1: Loosen the pre-installed bolts and adjust the length of the top frame to match the size of the table top.
- Step 2: Insert the Column to the top frame, fix lifting column with 4pcs screws M6x12.
- Step 3: Place the table feet on the Column and rotate it to align, then tighten the pre-installed bolt.
- Step 4: Place the side bracket on the top frame and tighten the bolts.
- Step 5: Mount the tabletop and fix it with 14 pcs screws ST4x20. Fix the centre bracket with 2 pcs screws M6x10. Tighten the pre-installed bolts on the top frame.
Cable Tray Installation
- Step 1: Fix the cable tray(B2-SSCT) to the cable tray arms(HP-SSARM) with 8 pcs M6x10 screws.
- Step 2: Install the U brackets to the desk frame with 4 pcs M8x10 screws. Mount the cable tray to the desk frame and fix it with 6 pcs M6x10 screws.
Screen Panel Installation
- Step 1: Insert the tapped plates to the screen panel (plates can be found in B2-SBRAC carton).
- Step 2: Install the screen brackets (B2-SBRAC) to the Shush30 Extrusion with 8 pcs M5x6 screws.
- Step 3: Fix the screen brackets (B2-SBRAC) to the desk frame with 10 pcs M6x10 screws.
EPS (900mm H Eco Panel) Screen Panel Installation
- Step 1: Install the screen brackets(B2-SBRAC) on the cable tray arm(HP-SSARM) with 10 PCS M6x10 Screws. The brackets direction as photos display.
- Step 2: Place the EPS panel on the screen brackets. Using a 6mm drill bit (not included), drill out holes in Eco Panel Screen in line with back-to-back screen bracket holes. Place 8 x Double Ended Bolts M5*32mm – 6mm through The screen bracket (B2-SBRAC) holes and the holes you have created in the Eco Panel Screen. Tighten double-ended bolt with Allen key.
FAQ’s
Are additional tools required for assembly?
No, all necessary tools are included in the package.
Can the workstation frame be adjusted for different heights?
The workstation frame is fixed height and cannot be adjusted.
Documents / Resources
 |
Rapidline Halo Static Single Sided Fixed Height Workstation Frame [pdf] Instruction Manual Halo Static Single Sided Fixed Height Workstation Frame, Halo Static Single Sided Fixed Height Workstation Frame, Single Sided Fixed Height Workstation Frame, Fixed Height Workstation Frame, Workstation Frame, Frame |