មាតិកា
លាក់
Rapidline Halo Static Single Sided Fixed Height Workstation សៀវភៅណែនាំណែនាំអំពីស៊ុម
លក្ខណៈបច្ចេកទេស
- Frame Type: Static Single Sided Fixed Height Workstation
- សម្ភារៈស៊ុម: ដែក
- Frame Color: Black
- Table Feet: 2 pieces
- Column: 2 pieces (1 right, 1 left)
- Bolts: M6x12 (5 pieces), M6x10 (3 pieces)
- Screws: ST4x20 (22 pieces), M6x12 (4 pieces), M5x6 (8 pieces)
- Tools Included: Allen Wrench 4mm (1 piece), Allen Wrench 5mm (1 piece), Cable Tie (5 pieces)
ផ្នែកសមាសធាតុ
| ទេ | ឈ្មោះសមាសធាតុ | កុំព្យូទ័រ | ទេ | ឈ្មោះសមាសធាតុ | កុំព្យូទ័រ |
|---|---|---|---|---|---|
| 1 | ជើងតុ | 2 | 9 | តង្កៀបកណ្តាល | 1 |
| 2 | Column (right) | 1 | 10 | ផ្លូវរថភ្លើងកណ្តាល | 2 |
| 3 | ប៊ូឡុង៖ M6x12 | 5 | 11 | ស៊ុមកំពូល - 2 | 1 |
| 4 | វីសៈ ST4x20 | 22 | 12 | Column (left) | 1 |
| 5 | តង្កៀបចំហៀង | 2 | 13 | Allen Wrench (៦ ម។ ម។ ) | 1 |
| 6 | បន្ទះកៅស៊ូ | 14 | 14 | Allen Wrench (៦ ម។ ម។ ) | 1 |
| 7 | ស៊ុមកំពូល - 1 | 1 | 15 | ខ្សែចង | 5 |
| 8 | ប៊ូឡុង៖ M6x10 | 3 |
សេចក្តីណែនាំអំពីការជួបប្រជុំគ្នា។
- ជំហានទី 1៖ Loosen the pre-installed bolts and adjust the length of the top frame to match the size of the table top.
- ជំហានទី 2៖ Insert the Column to the top frame, fix lifting column with 4pcs screws M6x12.
- ជំហានទី 3៖ Place the table feet on the Column and rotate it to align, then tighten the pre-installed bolt.
- ជំហានទី 4៖ ដាក់តង្កៀបចំហៀងនៅលើស៊ុមខាងលើហើយរឹតបន្តឹងប៊ូឡុង។
- ជំហានទី 5៖ Mount the tabletop and fix it with 14 pcs screws ST4x20. Fix the centre bracket with 2 pcs screws M6x10. Tighten the pre-installed bolts on the top frame.
ការដំឡើងថាសខ្សែកាប
- ជំហានទី 1៖ Fix the cable tray(B2-SSCT) to the cable tray arms(HP-SSARM) with 8 pcs M6x10 screws.
- ជំហានទី 2៖ Install the U brackets to the desk frame with 4 pcs M8x10 screws. Mount the cable tray to the desk frame and fix it with 6 pcs M6x10 screws.
ការដំឡើងបន្ទះអេក្រង់
- ជំហានទី 1៖ Insert the tapped plates to the screen panel (plates can be found in B2-SBRAC carton).
- ជំហានទី 2៖ Install the screen brackets (B2-SBRAC) to the Shush30 Extrusion with 8 pcs M5x6 screws.
- ជំហានទី 3៖ Fix the screen brackets (B2-SBRAC) to the desk frame with 10 pcs M6x10 screws.
EPS (900mm H Eco Panel) Screen Panel Installation
- ជំហានទី 1៖ Install the screen brackets(B2-SBRAC) on the cable tray arm(HP-SSARM) with 10 PCS M6x10 Screws. The brackets direction as photos display.
- ជំហានទី 2៖ Place the EPS panel on the screen brackets. Using a 6mm drill bit (not included), drill out holes in Eco Panel Screen in line with back-to-back screen bracket holes. Place 8 x Double Ended Bolts M5*32mm – 6mm through The screen bracket (B2-SBRAC) holes and the holes you have created in the Eco Panel Screen. Tighten double-ended bolt with Allen key.
សំណួរគេសួរញឹកញាប់
តើត្រូវការឧបករណ៍បន្ថែមសម្រាប់ការផ្គុំទេ?
ទេ ឧបករណ៍ចាំបាច់ទាំងអស់ត្រូវបានរួមបញ្ចូលនៅក្នុងកញ្ចប់។
Can the workstation frame be adjusted for different heights?
The workstation frame is fixed height and cannot be adjusted.
ឯកសារ/ធនធាន
 |
Rapidline Halo Static Single Sided Fixed Height Workstation Frame [pdf] សៀវភៅណែនាំ Halo Static Single Sided Fixed Height Workstation Frame, Halo Static Single Sided Fixed Height Workstation Frame, Single Sided Fixed Height Workstation Frame, Fixed Height Workstation Frame, Workstation Frame, Frame |