QUIN D420D Label Printer User Manual

QUIN D420D Label Printer

PRO TIPS

• Each time you change the label, please run the automatic label identification.
• Press the feed button on the printer to skip a blank label.
• Double click the feed button to print a test page.
• Avoid poor quality labels as they can damage the printer.
• Regularly clean the print head.
• If the paper is jammed and the red light is flashing slowly, run the automatic label identification.
• Insert Label Printer into the same USB port on your computer every time. This will avoid creating duplicate copies of the printer in your operating system.

FAQ

Q: Bluetooth won’t connect (using a phone as an example)

1. Standard troubleshooting steps:
   • Update the Labe life app to the latest version.
   • Restart the printer and the app.
   • Keep your phone within 10 meters of the printer, and ensure no other device is connected to it..
   • Test with another phone.
2. Phone detects the printer in Bluetooth settings, but the app doesn’t:
   • Unpair the printer in your phone’s Bluetooth settings →
     Restart the printer Search again in the app.
3. Neither the phone nor the app can find the printer:
   • Reset the printer:
     Turn it off→ Hold down the Feed button→ While holding it, turn the
     printer on → Release the button when the red light flashes →
     Wait for the blue light to stay on.
   • Restart your phone and try again.

Q: Printing stops and the red light flashes
The printer requires paper calibration.
Please turn the printer off and on, then hold the Feed button for 3 seconds to re-calibrate.

Q: Blank Print

The label paper may not be properly installed, or it is not thermal label paper.

Please:

1. Place the printing side facing up.
2. Use thermal paper.

Q: Incomplete Print

The label size setting may not match the paper size.

Please:

1. Set the label size in the app to match the actual label dimensions
   (e.g. 4×6 in/4×8 in) and reprint.
2. Download the Labe life App for custom editing.

Note: For more help, scan the QR code on the printer or visit the official website for tutorials.

LED STATUS LIGHT

Light	Printer Status
Solid blue	Standby and Ready
Blue flashing	Pause printing
Solid red	Cover is not closed
Red flashing	Label jams or label detection error
Purple flashing	Print head overheating
Solid purple	Printing

FEED BUTTON

CANCEL BUTTON

Function	Cancel the print job
Operation	During printing, press once to cancel the remaining print job.

SAFETY NOTICES

• The print head may be very hot after printing labels. Do not touch the print head.
• Do not bend the power cord excessively or place objects on the cord.
• Do not use the printer if you find any irregularities as these could result in fire or electric shock.
• Keep the printer out of reach of children.
• Use only approved accessories and do not try to disassemble, repair the unit by yourself.
• Keep the printer away from water and other objects that could penetrate the components.
• Please unplug the printer when it is not in use for a long time.

ISED Warning statement:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

ISED RF exposure statement:

This equipment complies with ISED Radiation exposure limit set forth for uncontrolled environment.

This equipment should be installed and operated with a minimum distance of 20cm between the product and your body.

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.

FCC RF exposure statement:

The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum 20cm distance between the radiator and your body.