د پانډا ذراتو پیچ کول د یوروریک ټریګر ماډلولیشن
مشخصات
- مخکې راټول شوي برېښنايي اجزا
- نازک لوړ ټیک الیکترونیکونه
- Includes male pin headers, metal spacers, mini PCB, and jack connectors
- د الیکټروسټاټیک خارجیدو (ESD) محافظت
- ۲۳ روښانه شوي پش بټنونه
ستونزمنه درجه
- د خپل نوي ماډل د راټولولو لپاره، په راتلونکو څو پاڼو کې ورکړل شوي ګامونه تعقیب کړئ. پداسې حال کې چې ټول بریښنایی اجزا مخکې له مخکې راټول شوي وي، تاسو به د هارډویر اجزا نصب او خوندي کولو ته اړتیا ولرئ.
- دا مهمه ده چې تصدیق شي چې ټولې میخانیکي برخې په سمه توګه تنظیم شوي او د سولډر کولو دمخه په سمه توګه ځای پر ځای شوي دي. ډاډ ترلاسه کړئ چې د هرې برخې سمت دوه ځله وګورئ ترڅو ډاډ ترلاسه کړئ چې هرڅه په سمه توګه نصب شوي دي.
- هر ګام په ترتیب سره تعقیب کړئ، او اجزا په احتیاط سره اداره کړئ، ځکه چې دا نازک لوړ ټیک برقیات دي.
A Note on Electrostatic Discharge (ESD)
Electrostatic discharge (ESD) هغه وخت پیښیږي کله چې جامد بریښنا رامینځته شي او خارج شي ، لکه یو کوچنی شاک چې تاسو یې د فلزي دروازې د لمس کولو پرمهال احساس کوئ. ESD کولی شي حساس بریښنایی اجزاو ته زیان ورسوي. د مجلس په جریان کې ستاسو د ماډل سرکټري ساتلو لپاره:
- د سرکټ بورډ اداره کولو دمخه د فلزي سطحې یا ځمکني څیز په لمس کولو سره خپل ځان مینځئ.
FOLLOW THESE STEPS FOR BUILDING THIS KIT
- د غونډې پروسې پیل کولو لپاره برخې چمتو کړئ.
- Locate the two metal spacers, 2x4mm, 1 mini PCB for the jack connectors and 2 male pin headers:
- one with 5 pins (1×5) and one with 6 pins (1×6)
- one with 5 pins (1×5) and one with 6 pins (1×6)
- Place and screw the spacers on the PCB as shown in the image.
- Insert the 1×5 and 1×6 male pin headers the mini jack PCB. Ensure the thicker (wider) side of the pins is inserted into the mini PCB holes. This ensures a proper fit and electrical connection.
- Insert the exposed ends of the two pin headers into the holes on the control PCB. Align both PCBs, use the 2 metal spacers to screw them together. Only solder the pin headers on the mini PCB side. Do not solder the pins on the control PCB.
- Separate the mini PCB from the CTRL PCB. Insert all the audio jacks into their positions on the mini PCB. Take special note of the ground pin holes; the circled jack ground pins share the same hole.
- Ensure all jacks are fully seated and aligned and proceed to solder them.
- Using a pair of pliers, carefully snap off the side section of the PCBs. Apply gentle but firm pressure, avoid twisting the board to prevent damaging.
- Carefully align and attach the PCBs by fitting it onto the female headers. Once the boards are properly aligned and seated, solder the header pins on the control PCB side.
- Locate all 23 illuminated push buttons. Pay close attention to polarity: on the bottom of each button, you’ll see+ and – symbols. Align the + pin on each button with the + marking on the PCB.
- Insert all 23 illuminated push buttons & metal spacers into their designated positions on the control PCB. Pay close attention to the polarity of the buttons. Incorrect orientation be very difficult to fix after soldering.
- Carefully insert the mini jack PCB back into the control PCB. Screw both PCBs together using the metal spacers. Do not solder the pin headers at this stage
- Carefully place the front panel onto the assembled PCBs. Secure the panel by tightening 2 jack nuts on opposite corners to hold it in place.
- Use a pointed tool with a rubber tip to avoid scratching the button caps and gently align each button with its hole in the panel, starting with the top row of 4 buttons and working your way down.
- Once a button is properly aligned, use your finger to lightly press it from behind the PCB so it clicks into place and sits flush against the panel. Do not press too hard; excess force can dislodge the button.
- Once the last button is aligned, the front panel should sit correctly on the metal spacers. Screw the front panel to the PCB using the remaining screws. Gently press each button to ensure they are fully seated.
- Carefully inspect the alignment of the buttons. From behind the PCB, look carefully for any empty holes with no pins inserted. Correcting soldering mistakes at this point will be extremely difficult. Once confirmed, proceed to solder.
- Carefully connect the control PCB to the main PCB by inserting the male pin headers into the female headers.
- Double-check the alignment: make sure that each pin lines up correctly with its corresponding socket. Congratulations, you are done!
- Double-check the alignment: make sure that each pin lines up correctly with its corresponding socket. Congratulations, you are done!
FAQ
پوښتنه: زه څنګه د اسمبلۍ په جریان کې د ماډل سرکټري ساتنه وکړم؟
A: Ground yourself before handling the circuit board by touching a metal surface or a grounded object to prevent Electrostatic Discharge (ESD).
پوښتنه: که چیرې یوه برخه په سمه توګه تنظیم شوې نه وي نو زه باید څه وکړم؟
A: Double-check the orientation of each component before soldering to ensure proper alignment. Re-align as needed before proceeding with soldering.
اسناد / سرچینې
 |
د پانډا ذراتو پیچ کول د یوروریک ټریګر ماډلولیشن [pdf] د نصبولو لارښود ذرې د یوروریک ټریګر ماډلولیشن، د یوروریک ټریګر ماډلولیشن، د ټریګر ماډلولیشن، ماډلولیشن |