Brainchild

ਬ੍ਰੇਨਚਾਈਲਡ IA10 ਸੂਚਕ ਅਤੇ ਅਲਾਰਮ ਯੂਨਿਟ ਉਪਭੋਗਤਾ ਗਾਈਡ

ਬ੍ਰੇਨਚਾਈਲਡ IA10 ਸੂਚਕ ਅਤੇ ਅਲਾਰਮ ਯੂਨਿਟ

 

IA10 ਸੂਚਕ ਅਤੇ ਅਲਾਰਮ ਯੂਨਿਟ
ਮਾਡਲ: IA10 ਵਰਜਨ QS0IA101A EN

 

1 ਓਵਰVIEW ਅਤੇ ਦਿੱਖ

FIG 1 Front Panel and Function

FIG 2 Front Panel and Function

 

FIG 3 Front Panel and Function

 

2. ਡਿਸਪਲੇਅ ਅਤੇ ਕੁੰਜੀਆਂ

FIG 4 DISPLAY AND KEYS

 

3 ਮੀਨੂ ਫਲੋ ਚਾਰਟ

ਮੀਨੂ ਨੂੰ 5 ਸਮੂਹਾਂ ਵਿੱਚ ਵੰਡਿਆ ਗਿਆ ਹੈ। ਉਹ ਹੇਠ ਲਿਖੇ ਅਨੁਸਾਰ ਹਨ:

FIG 5 MENU FLOW CHART

 

1) ਪੀਵੀ ਅਤੇ ਸੈੱਟਪੁਆਇੰਟ (ਪੀਵੀ1/ਪੀਵੀ2)
2) Manual Mode Menu (MANU)
3) Setup Menu (SET)
4) Calibration Mode Menu (CALI)

 

FIG 6 MENU FLOW CHART

 

ਨੋਟ:
The flow chart shows a complete list of all parameters. For actual application, the number of available parameters will vary depending on the setup and will be less than that shown in the flow chart.

 

4. ਪੈਰਾਮੀਟਰ ਵਰਣਨ

ਅੰਜੀਰ 7 ਪੈਰਾਮੇਟਰ ਵੇਰਵੇ

ਅੰਜੀਰ 8 ਪੈਰਾਮੇਟਰ ਵੇਰਵੇ

ਅੰਜੀਰ 9 ਪੈਰਾਮੇਟਰ ਵੇਰਵੇ

ਅੰਜੀਰ 10 ਪੈਰਾਮੇਟਰ ਵੇਰਵੇ

ਅੰਜੀਰ 11 ਪੈਰਾਮੇਟਰ ਵੇਰਵੇ

ਅੰਜੀਰ 12 ਪੈਰਾਮੇਟਰ ਵੇਰਵੇ

ਅੰਜੀਰ 13 ਪੈਰਾਮੇਟਰ ਵੇਰਵੇ

 

ਅੰਜੀਰ 14 ਪੈਰਾਮੇਟਰ ਵੇਰਵੇ

ਅੰਜੀਰ 15 ਪੈਰਾਮੇਟਰ ਵੇਰਵੇ

ਅੰਜੀਰ 16 ਪੈਰਾਮੇਟਰ ਵੇਰਵੇ

 

5. ਸੰਚਾਰ ਪਤਾ ਪੂਰੀ ਸਾਰਣੀ v1.2

FIG 17 Communication Address Full Table v1.2

FIG 18 Communication Address Full Table v1.2

 

6. ਪ੍ਰੋਗਰਾਮਿੰਗ

ਸਿਗਨਲ ਇਨਪੁਟ
INPT: Select the sensor type or signal type for signal input
Range: (Thermocouple) J_tC, K_tC, T_tC, E_tC, B_tC, R_tC, S_tC, N_tC, L_tC, U_tC, P_tC, C_tC, d_tC(RTD) PT.DN, PT.JS, (Linear) 4-20, 0-20, 0-5V, 1-5V, 0-10V, 0-1V, 0-50mV

ਪੁਨਰ ਪ੍ਰਸਾਰ
The signal conditioner will output (retransmit) PV on its output terminals of output1, output2 and output3. ANL1 and ANH1 are adjusted to specify the low scale and high scale values of output1 retransmission. Similarly, ANL2, ANL3, ANH2 and ANH3 parameters are adjusted for output2 and output3.

Zero and Span adjustment
The signal conditioner has the option to adjust the zero and span of the outputs to meet the required accuracy. The user can adjust the parameters otZ1, otZ2 and otZ3 to adjust the zero value of the output1, output2 and output3 respectively. The user can adjust the parameters otS1, otS2 and otS3 to adjust the span value of the output1, output2 and output3 respectively. The allowable range for zero and span adjustment is from -1.000 to 1.000.

FIG 19 Zero and Span adjustment

 

7. ਗਲਤੀ ਕੋਡ

ਚਿੱਤਰ 20 ਗਲਤੀ ਕੋਡ

 

8. ਵਾਇਰਿੰਗ ਡਾਇਗਰਾਮ

ਚਿੱਤਰ 21 ਵਾਇਰਿੰਗ ਡਾਇਗਰਾਮ

ਟਰਮੀਨਲ ਕਨੈਕਸ਼ਨ

 

ਚਿੱਤਰ 22 ਵਾਇਰਿੰਗ ਡਾਇਗਰਾਮ

For assistance contact Tech Support: service@brainchild.com.tw; 886-2-2786-1299; http:// www.brainchildtw.com
**This specification is subject to possible change without prior notice.
Copyright © 2025, All Right Reserved

 

ਇਸ ਮੈਨੂਅਲ ਬਾਰੇ ਹੋਰ ਪੜ੍ਹੋ ਅਤੇ PDF ਡਾਊਨਲੋਡ ਕਰੋ:

ਦਸਤਾਵੇਜ਼ / ਸਰੋਤ

ਬ੍ਰੇਨਚਾਈਲਡ IA10 ਸੂਚਕ ਅਤੇ ਅਲਾਰਮ ਯੂਨਿਟ [pdf] ਯੂਜ਼ਰ ਗਾਈਡ
QS0IA101A, EN, IA10 ਸੂਚਕ ਅਤੇ ਅਲਾਰਮ ਯੂਨਿਟ, IA10, ਸੂਚਕ ਅਤੇ ਅਲਾਰਮ ਯੂਨਿਟ, ਅਲਾਰਮ ਯੂਨਿਟ, ਯੂਨਿਟ

ਹਵਾਲੇ

ਇੱਕ ਟਿੱਪਣੀ ਛੱਡੋ

ਤੁਹਾਡਾ ਈਮੇਲ ਪਤਾ ਪ੍ਰਕਾਸ਼ਿਤ ਨਹੀਂ ਕੀਤਾ ਜਾਵੇਗਾ। ਲੋੜੀਂਦੇ ਖੇਤਰਾਂ ਨੂੰ ਚਿੰਨ੍ਹਿਤ ਕੀਤਾ ਗਿਆ ਹੈ *