OVVO V-0930 Connection System User Guide

Releasable Specifications

V-0930 Releasable

V-0930RH

V-0930RC

V-0930PH

1. Plunge
2. Travel
3. Out
   

   

Depth Tolerances:
9.5mm, +/- 0.5mm

Travel (Centre to Centre): 20.6mm
Out to Out: 30mm
CNC speeds vary with different materials. Maximum cutter rotation: 18,000

How it works

Recommended Minimum Board Depth

Recommended minimum board depth or thickness values for the V-0930 will change depending on both the substrate material used as well as the joint angle.

Minimum recommended measurements shown below are categorized according to two distinct groups of board material which share broadly similar connector retention properties.

HPL, Composite, Solid Surface, Hardwoods, Birch Plywood
	A	B
Fig 1	12mm	12mm
Fig 2	12mm	12mm
Fig 3	12mm	12mm
Fig 4	14mm	14mm
Fig 5	12mm	19mm
Fig 6	12mm	12mm
Fig 7	12mm	12mm
Fig 8	12mm	12mm
Fig 9	12mm	12mm
Fig 10	12mm	12mm

Particle/Chipboard, Softwoods, MDF
	A	B
Fig 1	15mm	15mm
Fig 2	12mm	12mm
Fig 3	16mm	12mm
Fig 4	15mm	15mm
Fig 5	15mm	19mm
Fig 6	15mm	12mm
Fig 7	15mm	15mm
Fig 8	15mm	15mm
Fig 9	15mm	15mm
Fig 10	15mm	15mm

These are guidelines only and OVVO® recommends trial connections be made before going into full production

Shear & Tensile

	18mm Chipboard		18mm MDF		18mm Plywood		12mm Plywood		12mm HPL
	Permanent	Releasable	Permanent	Releasable	Permanent	Releasable	Permanent	Releasable	Permanent	Releasable
	65kg	52.5kg	67.5kg	42.5kg	140kg	82.5kg	75kg	57.5kg	–	–
	150kg	130kg	180kg	130kg	475kg	325kg	175kg	110kg	–	–
	40kg	40kg		–	–	–	–	–	–	–
	85kg	85kg	–	–	–	–	–	–	–	–
	50kg	30kg	50kg	35kg	–	–	85kg	45kg	100kg	50kg
	105kg	70kg	137.5kg	90kg	–	–	170kg	105kg	230kg	140kg

Releasable Instructions

http://ovvotech.com/help

Milling

1. Plunge
2. Travel
3. Out

Depth Tolerances:
9.5mm, +/- 0.5mm

Travel Centre to Centre: 20.6mm
Rotation Speed: CNC speeds vary with different materials. Maximum cutter rotation: 18,000.
Recommended Spacing

1. 35mm to 80mm
2. : 100mm to 250mm
   

Housing

Assembly

Simply push or slide to connect

Release

How it works

Simply push or slide to connect

Permanent Instructions

Milling

1. Plunge
2.  Travel
3.  Out
   

Depth Tolerances:
9.5mm, +/- 0.5mm

Travel Centre to Centre: 20.6mm
Rotation Speed: CNC speeds vary with different materials. Maximum cutter rotation: 18,000.

Housing

Assembly – Simply push into place to connect

Important! Set Depth Correctly

IMPORTANT! MAKE A TEST

RECOMMENDED DEPTH TOLERANCES
V-0930	9.5mm, +/- 0.5mm

Set the depth tolerance to 9.5mm and adjust +/- 0.5mm if required

Less than 9mm will create an open joint

Greater than 10mm connector wing can not lock

Depth Setting Guide

1. Make a long cut with your tooling. Approximately 200mm long and 9.5mm depth
   
   
2. Cut in half
   
3. Insert Connection Set and check depth.
   

 

Documents / Resources

OVVO V-0930 Connection System [pdf] User Guide V-0930 Connection System

References

• User Manual