UNI-T UT330T USB Data Logger Instructions

UT330T USB Data Logger

Zofotokozera:

  • Model: UT330T/UT330TH/UT330THC
  • Kufotokozera: P / N: 110401112104X
  • Type: USB Datalogger
  • Batri: 3.0V CR2032

Malangizo Ogwiritsira Ntchito Zogulitsa:

Zambiri Zachitetezo:

1. Check if the logger is damaged before use.

2. Replace the battery when the logger displays a low battery
chizindikiro.

3. Stop using the logger if it is found to be abnormal and
contact your seller.

4. Do not use the logger near explosive gas, volatile gas,
corrosive gas, vapor, and powder.

5. Do not charge the battery; replace with a 3.0V CR2032
batire.

6. Install the battery according to its polarity and remove if
osagwiritsidwa ntchito kwa nthawi yayitali.

Kapangidwe kazinthu:

1. Chivundikiro cha USB

2. Indicator (Green light: logging, red light: alarm)

3. Onetsani zenera

4. Stop/switch humidity and temperature (UT330TH/UT330THC)

5. Start/select

6. Wogwirizira

7. Air vent (UT330TH/UT330THC)

8. Battery Cover Opened Rib

Zowonetsa:

1. Yambani

2. Mtengo wapamwamba

3. Imani

4. Minimum value

5. Kuyika chizindikiro

6. Circulatory

7. Mean kinetic temperature

8. Number of sets

9. Kutentha

10. Batire yotsika

11. Chinyezi unit

12. Temperature & humidity display area

13. Time display area

14. Set a fixed time/delay

15. Alarm due to abnormal logging

16. Palibe alamu

17. Lower value of alarm

18. Upper value of alarm

Malangizo Okhazikitsira:

  1. USB Communication:
  2. – Download the instruction and PC software from the attached
    file.

    – Install the software by following the provided steps.

    – Insert the logger into the USB port of a PC; the logger’s main
    interface will display USB.

    – Open the software on the PC to set parameters and analyze
    deta.

  3. Kukonzekera kwa Parameter:
  • Kufotokozera: Users can add descriptions (less
    than 50 words) that will show in the generated PDF.
  • UTC/Time Zone: Set according to local time
    zone and obtain real-time PC time.
  • Nthawi ya Chipangizo: Update device time by
    synchronizing with PC time.
  • Mode: Select Single/Accumulate alarm
    mode.
  • Poyambira: Set alarm thresholds for
    kutentha ndi chinyezi.
  • Kuchedwa: Determine the alarm state delay time
    (0s to 10h).
  • Kujambulira: Choose Normal/Circulatory
    mode.
  • Sampchinenero: Masekondi 10 mpaka 24
    maola.
  • Sampling Delay: Mphindi 0 mpaka 240.
  • Yambani/Imitsani: Configure logging start and stop
    zosankha.
  • Write/Read/Close: Perform operations with
    parameters and logger data.

Setting Interface of the PC Software

Mafunso Ofunsidwa Kawirikawiri (FAQ):

Q: What should I do if the logger displays a low battery
chizindikiro?

A: Replace the battery with a new 3.0V CR2032 battery.

Q: How can I set the alarm thresholds for temperature and
chinyezi?

A: Use the software to configure the desired threshold values in
the parameter settings.

Q: Can I charge the battery of the logger?

A: No, do not charge the battery; replace it with a new CR2032
batire ikafunika.

Q: How do I know if the logger is logging data?

A: The green light indicator on the logger signifies that it is
in logging mode.

"``

P/N: 110401112104X

UT330T/UT330TH/UT330THC

USB Datalogger

Mawu Oyamba

USB datalogger (Panopa imatchedwa "logger") ndiyomwe imagwiritsa ntchito mphamvu zochepa, kutentha kwambiri komanso chinyezi. Ili ndi mawonekedwe olondola kwambiri, kusungirako kwakukulu, kusungirako magalimoto, kutumiza kwa data ya USB, kuwonetsa nthawi ndi kutumiza kunja kwa PDF. Ikhoza kukwaniritsa zofunikira za miyeso yosiyanasiyana ndi kujambula kwa nthawi yaitali ndi kutentha kwa chinyezi, ndipo ingagwiritsidwe ntchito pokonza chakudya, kusuntha kwaunyolo wozizira, kusungirako katundu ndi madera ena. UT330T idapangidwa ndi IP65 fumbi / chitetezo chamadzi. UT330THC ikhoza kulumikizidwa ku foni yamakono ya Android kapena kompyuta kudzera pa mawonekedwe a Type-C kuti aunike ndi kutumiza deta mu smartphone APP kapena pulogalamu ya PC.

Zida

Logger(with holder)…………………1 piece User manual………………………..1 piece Battery………………………………1 piece Screw………………………………..2 pieces

Zambiri zachitetezo

Check if the logger is damaged before use. Replace the battery when the logger displays ” “.

If the logger is found abnormal, please stop using and contact your seller. Do not use the logger near explosive gas, volatile gas, corrosive gas, vapor and powder.

Do not charge the battery. 3.0V CR2032 battery is recommended.

Install the battery according to its polarity. Take out the battery if the logger is not used for a long time.

Kapangidwe (Chithunzi 1)

Ayi.

Kufotokozera

1 USB cover

2 Indicator (Green light: logging, red light: alarm)

3 Kuwonetsa skrini

4 Stop/switch humidity and temperature(UT330TH/UT330THC)

5 Start/select

6 chofukizira

7 Air vent (UT330TH/UT330THC)

8 Battery Cover Opened Rib

Chiwonetsero (chithunzi 2)

Chithunzi 1

Ayi.

Kufotokozera

Ayi.

Kufotokozera

1 Yambani

10 Batire yotsika

2 Maximum value

11 Humidity unit

Imani

12 Temperature & humidity display area

4 Minimum value

13 Time display area

5 Kuyika chizindikiro

14 Set a fixed time/delay

6 Circulatory

15 Alarm due to abnormal logging

7 Mean kinetic temperature 16 No alarm

8 Number of sets

17 Lower value of alarm

9 Kutentha kwapakati

18 Upper value of alarm

Chithunzi 2

Kukhazikitsa

Kuyankhulana kwa USB

Koperani malangizo ndi PC mapulogalamu malinga ndi Ufumuyo file, then, install the software step by step. Insert the logger into USB port of PC, the main interface of logger will display “USB”. After the computer identifies the USB, open the software to set parameters and analyze the data. (Figure 3).

Tsegulani pulogalamu yapakompyuta kuti musakatule ndikusanthula deta. Ponena za momwe mungagwiritsire ntchito pulogalamuyo, ogwiritsa ntchito amatha kudina njira yothandizira pa mawonekedwe opangira kuti apeze "mapulogalamu apulogalamu".

Kukonzekera kwa parameter

Model Unit Language ID SN

The computer identifies the logger model automatically. °C or °F. The generated report language can be set to English or Chinese. Users can set the ID, the range is 0~255. Factory number.

Kufotokozera

Ogwiritsa akhoza kuwonjezera mafotokozedwe. Kufotokozera kudzawonetsedwa mu PDF yopangidwa ndipo kuyenera kukhala mawu osakwana 50.

UTC/Time zone PC time

The product uses the UTC time zone, which can be set according to the local time zone. Obtain PC time in real time.

Chipangizo nthawi

Pezani nthawi yomwe chipangizocho chilumikizidwa. Chongani "Sinthani" ndi kumadula "Lembani", logger adzakhala synchronize ndi PC nthawi.

Mode

Ogwiritsa ntchito amatha kusankha Single/Accumulate alarm mode.

Poyambira

Ogwiritsa akhoza kukhazikitsa alamu. Kutentha kochepa (kutsika kwa chinyezi) kuyenera kukhala kochepa kusiyana ndi kutentha kwapamwamba (chinyezi chachikulu).

Delay Temperature and humidity Adjusting Recording mode Sampling interval Sampling delay Start with Stop with key Write Read Close

Nthawi yochedwa yomwe imagwiritsidwa ntchito kudziwa momwe ma alarm (0s mpaka 10h)
Liniya kutentha ndi kusintha chinyezi -6.0°C(RH%)~6.0°C(RH%)
Normal/Circulatory 10 seconds to 24 hours. Start logging after the delay time. 0 to 240 minutes. Press the button to start, start immediately through the software, start at a fixed time. Choose if press the button to stop.prevent recording stop resulting from misoperation. Write parameters to the logger. Read logger parameters into the computer software. Close the interface.

Figure 3 (Setting Interface of the PC Software)
Zochita
Starting the logger There are three starting modes: 1.Press the button to start the logger 2.Start logging through the software

3.Start logging at preset fixed time
Mode 1: Long press the start button for 3 seconds in main interface to start logging. This start mode supports start delay, if delay time is set, the logger will start logging after a delayed time. Mode 2: Start logging through the software: On PC software, when parameter setting is completed, the logger will start logging after user unplugs the logger from the computer. Mode 3: Start the logger at preset fixed time: On PC software, when parameter setting is completed, the logger will start logging at preset time after user unplugs the logger from the computer. Mode 1 now is disabled.
Chenjezo: chonde sinthani batire ngati chizindikiro champhamvu chayaka.

Osadula mitengo

Kudula mitengo

Kuyimitsa wodula mitengo

Delay logging Logging at fixed time

There are two stop modes: 1.Press the button to stop 2.Stop logging through the software
Mode 1: In main interface, long press stop button for 3 seconds to stop the logger, If “Stop with key” is not checked in the parameter interface, this function cannot be used. Mode 2: After connecting the logger to the computer, click the stop icon on the main interface of the computer to stop logging.

Kujambulira mode

Normal: The logger automatically stops recording when the maximum number of groups is recorded. Circulatory: When the maximum number of groups is recorded, the latest records will replace the earliest records in turn. will show on the screen if this function is enabled.

Chiyankhulo cha Ntchito 1
UT330TH/UT330THC:Batani lalifupi loyimitsa kuti musinthe pakati pa kutentha ndi chinyezi pamawonekedwe akulu. Pamawonekedwe akulu, dinani pang'onopang'ono batani loyambira kuti mudutse mtengo woyezera, Max, Min, kutentha kwa kinetic, mtengo wapamwamba wa alamu, mtengo wotsika wa alamu, kutentha kwapano, kutentha kosankha (kanikizani mabatani a Start ndi Stop nthawi yomweyo. nthawi yosintha pakati pa mayunitsi), ndi mtengo woyezera. Ogwiritsa amatha kukanikiza batani loyimitsa pang'ono nthawi iliyonse kuti abwerere ku mawonekedwe akulu. Ngati palibe batani lopanikizidwa kwa masekondi 10, wodulayo adzalowa munjira yopulumutsa mphamvu.

Kuyika chizindikiro
Chipangizochi chikafika podula mitengo, dinani batani loyambira lalitali kwa masekondi atatu kuti mulembe zomwe zilipo kuti mudzazigwiritse ntchito m'tsogolo, chizindikiro cha chizindikiro ndi mtengo wapano udzawala katatu, chiwerengero chonse cha mtengo ndi 3.

Function Interface 2 In the main interface, press the start button and stop button together for 3 seconds to enter the Function Interface 2, short press start button to view: Y/M/D, ID ya chipangizo, manambala ochuluka a magulu osungira otsala, manambala amagulu olembera.
Alarm State When the logger is operating,
Alarm disabled: Green LED flashes every 15 seconds and main interface displays . Alarm enabled: Red LED flashes every 15 seconds and main interface displays ×. No LED lights when the logger is in stopping state. Note: The red LED will also flash when the low voltage alarm appears. Users should save the data in time andreplace the battery.
Viewdeta
Ogwiritsa angathe view deta yomwe ili yoyimitsidwa kapena yogwira ntchito.
View deta yomwe ili mu stop state: Lumikizani logger ku PC, ngati LED ikuwunikira panthawiyi, lipoti la PDF likupangidwa, musatulutse logger panthawiyi. Lipoti la PDF litapangidwa, ogwiritsa ntchito amatha kudina PDF file ku view ndi kutumiza deta kuchokera pakompyuta.
View deta yomwe ikugwira ntchito: Lumikizani logger ku PC, wodula mitengoyo apanga lipoti la PDF pazambiri zonse zam'mbuyomu, nthawi yomweyo, wodulayo apitilizabe kudula mitengo ndipo amatha kupanga lipoti la PDF ndi data yatsopano nthawi ina. .
Alarm setting and result Single: The temperature (humidity) reaches or exceeds the set threshold. If the continuous alarm time is not less than the delay time, the alarm will be generated. If the reading returns to normal within the delay time, no alarm will occu.r If the delay time is 0s, an alarm will be generated immediately. Accumulate: The temperature (humidity) reaches or exceeds the set threshold. If the accumulated alarm time is not less than the delay time, the alarm will be generated.

Kufotokozera

Kutentha Chinyezi

Ntchito Range
-30.0 20.1 -20.0 40.0 40.1 70.0
0 99.9% RH

UT330T Accuracy ±0.8 ±0.4 ±0.8
/

UT330TH Accuracy
± 0.4
± 2.5% RH

UT330THC Accuracy
± 0.4
± 2.5% RH

Protection degree Resolution Logging capacity Logging interval Unit/alarm setting
Start mode Logging delay
Device ID Alarm delay

IP65

/

/

Kutentha: 0.1 ° C; Chinyezi: 0.1% RH

64000 seti

10 ku 24h

Chigawo chokhazikika ndi °C. Mitundu ya ma alamu imaphatikizapo alamu imodzi komanso yosonkhanitsa, mtundu wokhazikika ndi alamu imodzi. Mtundu wa alamu ungasinthidwe kudzera pa PC yofewa.

Dinani batani kuti muyambitse logger kapena kuyambitsa logger kudzera pa pulogalamuyo (Nthawi yomweyo/kuchedwa/ panthawi yoikika).
0min 240min, imakhala yosasintha pa 0 ndipo imatha kusinthidwa kudzera pa pulogalamu ya PC.

Itha kukhazikitsidwa mu pulogalamu ya PC ndi smartphone APP

0 255, imasinthidwa kukhala 0 ndipo imatha kusinthidwa kudzera pa pulogalamu ya PC.

0s 10h, imasintha pa 0 ndipo imatha kusinthidwa kudzera pa pulogalamu ya PC.

Screen off time Battery type
Kutumiza kwa data
Working time Working temperature & humidity Storage temperature

10s

Mtengo wa CR2032

View ndi kutumiza deta mu pulogalamu ya PC

View ndi kutumiza deta mu pulogalamu ya PC ndi smartphone APP

140 days at an test interval of 15min (temperature 25)

-30°C ~ 70°C, 99%, non-condensable

-50°C ~70°C

Muyezo wa EMC: EN61326-1 2013.

Kusamalira
Battery replacement (Figure 4) Replace the battery with the following steps when the logger displays ” “.
Rotate the battery cover counter-clockwise. Install CR2032 battery and waterproof rubber ring(UT330TH) Install the cover in arrow direction and rotate it clockwise.

Kuyeretsa chodula mitengo

Pukuta chodulacho ndi nsalu yofewa kapena siponji yoviikidwa ndi madzi pang'ono, zotsukira, madzi a sopo.

Osayeretsa logger ndi madzi mwachindunji kuti musawononge gulu lozungulira.

Tsitsani

Chithunzi 4

Tsitsani pulogalamu ya PC molingana ndi kalozera wantchitoyo

Tsitsani pulogalamu ya PC kuchokera ku boma website of UNI-T product center :http://www.uni-trend.com.cn

Ikani

Dinani kawiri Setup.exe kuti muyike pulogalamuyo

Kuyika kwa UT330THC Android Smartphone APP
1. Preparation Please install the UT330THC APP on the smartphone first.
2. Installation 2.1 Search “UT330THC” in Play Store. 2.2 Search “UT330THC” and download on UNI-T’s official webtsamba:
https://meters.uni-trend.com.cn/download?name=62 2.3 Scan the QR code on the right. (Note: APP versions may be updated without prior notice.) 3. Connection
Lumikizani cholumikizira cha Type-C cha UT330THC ku mawonekedwe opangira ma smartphone, kenako tsegulani APP.

Zolemba / Zothandizira

UNI-T UT330T USB Data Logger [pdf] Malangizo
UT330T, UT330T USB Data Logger, USB Data Logger, Data Logger

Maumboni

Siyani ndemanga

Imelo yanu sisindikizidwa. Minda yofunikira yalembedwa *