UNI-T UT330T USB Data Logger Ntuziaka

UT330T USB Data Logger

“

Nkọwapụta:

• Model: UT330T/UT330TH/UT330THC
• P/N: 110401112104X
• Type: USB Datalogger
• Batrị: 3.0V CR2032

Ntuziaka ojiji:

Ozi nchekwa:

1. Check if the logger is damaged before use.

2. Replace the battery when the logger displays a low battery
egosi.

3. Stop using the logger if it is found to be abnormal and
contact your seller.

4. Do not use the logger near explosive gas, volatile gas,
corrosive gas, vapor, and powder.

5. Do not charge the battery; replace with a 3.0V CR2032
batrị.

6. Install the battery according to its polarity and remove if
adịghị eji ya ruo ogologo oge.

Nhazi ngwaahịa:

1. USB mkpuchi

2. Indicator (Green light: logging, red light: alarm)

3. Ngosipụta ihuenyo

4. Stop/switch humidity and temperature (UT330TH/UT330THC)

5. Start/select

6. Njide

7. Air vent (UT330TH/UT330THC)

8. Battery Cover Opened Rib

Ihe ngosi:

1. Malite

2. Ọnụ ahịa kachasị

3. Kwụsị

4. Minimum value

5. Ịka akara

6. Circulatory

7. Mean kinetic temperature

8. Number of sets

9. Ngalaba okpomọkụ

10. Batrị dị ala

11. Igwe iru mmiri

12. Temperature & humidity display area

13. Time display area

14. Set a fixed time/delay

15. Alarm due to abnormal logging

16. Enweghị mkpu

17. Lower value of alarm

18. Upper value of alarm

Ntuziaka ntọala:

1. USB Communication:

– Download the instruction and PC software from the attached
file.

– Install the software by following the provided steps.

– Insert the logger into the USB port of a PC; the logger’s main
interface will display USB.

– Open the software on the PC to set parameters and analyze
data.

2. Nhazi nhazi:

• Nkọwa: Users can add descriptions (less
  than 50 words) that will show in the generated PDF.
• UTC/Time Zone: Set according to local time
  zone and obtain real-time PC time.
• Oge ngwaọrụ: Update device time by
  synchronizing with PC time.
• Ụdị: Select Single/Accumulate alarm
  ọnọdụ.
• Ọnụ ụzọ: Set alarm thresholds for
  okpomọkụ na iru mmiri.
• igbu oge: Determine the alarm state delay time
  (0s to 10h).
• Ụdị ndekọ: Choose Normal/Circulatory
  ọnọdụ.
• SampOgologo oge: 10 sekọnd ruo 24
  awa.
• Sampling Delay: Nkeji 0 ruo 240.
• Malite/Kwụsị: Configure logging start and stop
  nhọrọ.
• Write/Read/Close: Perform operations with
  parameters and logger data.

Ajụjụ A na-ajụkarị (FAQ):

Q: What should I do if the logger displays a low battery
egosi?

A: Replace the battery with a new 3.0V CR2032 battery.

Q: How can I set the alarm thresholds for temperature and
iru mmiri?

A: Use the software to configure the desired threshold values in
the parameter settings.

Q: Can I charge the battery of the logger?

A: No, do not charge the battery; replace it with a new CR2032
batrị mgbe achọrọ.

Q: How do I know if the logger is logging data?

A: The green light indicator on the logger signifies that it is
in logging mode.

"'

P/N:110401112104X

UT330T/UT330TH/UT330THC

USB Datalogger

Okwu mmalite

USB datalogger (nke a na-akpọkwa ya “logger”) bụ ike oriri dị ala, ezigbo okpomọkụ na ngwaọrụ iru mmiri. Ọ nwere njirimara nke izi ezi dị elu, ikike nchekwa buru ibu, nchekwa akpaaka, nnyefe data USB, ngosipụta oge na mbupụ PDF. Ọ nwere ike izute chọrọ nke dị iche iche nha na ogologo oge okpomọkụ na iru mmiri ndekọ, na ike ji mee ihe na nri nhazi, oyi yinye njem, nkwakọba ihe na ndị ọzọ ubi. UT330T e mere na IP65 uzuzu / mmiri nchebe. Enwere ike ijikọ UT330THC na ekwentị gam akporo ma ọ bụ kọmpụta site na interface Type-C iji nyochaa na mbupụ data na ama APP ma ọ bụ ngwanrọ PC.

Ngwa ngwa

Logger(with holder)…………………1 piece User manual………………………..1 piece Battery………………………………1 piece Screw………………………………..2 pieces

Ozi nchekwa

Check if the logger is damaged before use. Replace the battery when the logger displays ” “.

If the logger is found abnormal, please stop using and contact your seller. Do not use the logger near explosive gas, volatile gas, corrosive gas, vapor and powder.

Do not charge the battery. 3.0V CR2032 battery is recommended.

Install the battery according to its polarity. Take out the battery if the logger is not used for a long time.

Nhazi (Foto 1)

Mba.

Nkọwa

1 USB cover

2 Indicator (Green light: logging, red light: alarm)

3 Ngosipụta ihuenyo

4 Stop/switch humidity and temperature(UT330TH/UT330THC)

5 Start/select

6 njide

7 Air vent (UT330TH/UT330THC)

8 Battery Cover Opened Rib

Ngosipụta (Foto 2)

Onyonyo 1

Mba.

Nkọwa

Mba.

Nkọwa

1 Malite

10 Batrị dị ala

2 Maximum value

11 Humidity unit

3 Kwụsị

12 Temperature & humidity display area

4 Minimum value

13 Time display area

5 Akara

14 Set a fixed time/delay

6 Circulatory

15 Alarm due to abnormal logging

7 Mean kinetic temperature 16 No alarm

8 Number of sets

17 Lower value of alarm

9 Okpomọkụ nkeji

18 Upper value of alarm

Onyonyo 2

Ịtọ ntọala

Nkwukọrịta USB

Budata ntuziaka na ngwa PC dị ka agbakwunyere file, then, install the software step by step. Insert the logger into USB port of PC, the main interface of logger will display “USB”. After the computer identifies the USB, open the software to set parameters and analyze the data. (Figure 3).

Mepee ngwanrọ kọmputa ka ịchọọ na nyochaa data. Banyere otu esi eji ngwanro, ndị ọrụ nwere ike pịa nhọrọ enyemaka na interface ọrụ iji chọta “akwụkwọ ntuziaka”.

Nhazi oke

Model Unit Language ID SN

The computer identifies the logger model automatically. °C or °F. The generated report language can be set to English or Chinese. Users can set the ID, the range is 0~255. Factory number.

Nkọwa

Ndị ọrụ nwere ike ịgbakwunye nkọwa. Nkọwa ga-egosi na PDF emepụtara ma kwesịrị ịbụ ihe na-erughị okwu 50.

UTC/Time zone PC time

The product uses the UTC time zone, which can be set according to the local time zone. Obtain PC time in real time.

Oge ngwaọrụ

Nweta oge ejikọrọ ngwaọrụ. Lelee "Mmelite" wee pịa "Dee", onye na-edebanye aha ga-emekọrịta na oge PC.

Ụdị

Ndị ọrụ nwere ike họrọ otu ọnọdụ mkpu.

Ọnụ ụzọ

Ndị ọrụ nwere ike ịtọ oke oti mkpu. Okpomọkụ dị ala (obere iru mmiri) ga-adị obere karịa oke okpomọkụ (oke iru mmiri).

Delay Temperature and humidity Adjusting Recording mode Sampling interval Sampling delay Start with Stop with key Write Read Close

Oge igbu oge ejiri iji chọpụta steeti mkpu (0s ruo 10h)
Mgbanwe okpomọkụ na iru mmiri linear -6.0°C(RH%)~6.0°C(RH%)
Normal/Circulatory 10 seconds to 24 hours. Start logging after the delay time. 0 to 240 minutes. Press the button to start, start immediately through the software, start at a fixed time. Choose if press the button to stop.prevent recording stop resulting from misoperation. Write parameters to the logger. Read logger parameters into the computer software. Close the interface.

Figure 3 (Setting Interface of the PC Software)
Ọrụ
Starting the logger There are three starting modes: 1.Press the button to start the logger 2.Start logging through the software

3.Start logging at preset fixed time
Mode 1: Long press the start button for 3 seconds in main interface to start logging. This start mode supports start delay, if delay time is set, the logger will start logging after a delayed time. Mode 2: Start logging through the software: On PC software, when parameter setting is completed, the logger will start logging after user unplugs the logger from the computer. Mode 3: Start the logger at preset fixed time: On PC software, when parameter setting is completed, the logger will start logging at preset time after user unplugs the logger from the computer. Mode 1 now is disabled.
Ịdọ aka ná ntị: biko dochie batrị ma ọ bụrụ na egosi ike dị ala dị.

Anaghị egbu osisi

Ịbanye

Ịkwụsị osisi osisi

Delay logging Logging at fixed time

There are two stop modes: 1.Press the button to stop 2.Stop logging through the software
Mode 1: In main interface, long press stop button for 3 seconds to stop the logger, If “Stop with key” is not checked in the parameter interface, this function cannot be used. Mode 2: After connecting the logger to the computer, click the stop icon on the main interface of the computer to stop logging.

Ụdị ndekọ

Normal: The logger automatically stops recording when the maximum number of groups is recorded. Circulatory: When the maximum number of groups is recorded, the latest records will replace the earliest records in turn. will show on the screen if this function is enabled.

Interface ọrụ 1
UT330TH/UT330THC: Obere bọtịnụ nkwụsị ka ịgbanwee n'etiti okpomọkụ na iru mmiri na isi interface. Na isi interface, obere pịa bọtịnụ Malite ka ịbanye na uru a tụrụ atụ, Max, Min, pụtara kinetic okpomọkụ, elu mkpu uru, ala mkpu uru unit ugbu a okpomọkụ unit, nhọrọ okpomọkụ unit (ogologo pịa Malite na Kwụsị bọtịnụ n'otu oge ahụ. oge iji gbanwee n'etiti nkeji), yana uru tụrụ. Ndị ọrụ nwere ike pịnye bọtịnụ nkwụsị n'oge ọ bụla iji laghachi na isi interface. Ọ bụrụ na enweghị bọtịnụ ọ bụla a pịara maka sekọnd 10, onye na-edebanye aha ga-abanye na ọnọdụ nchekwa ike.

Ịka akara
Mgbe ngwaọrụ ahụ nọ na ndekọ ndekọ, ogologo pịa bọtịnụ mmalite maka sekọnd 3 ka ị mara data dị ugbu a maka ntụnye aka n'ọdịnihu, akara akara na uru dị ugbu a ga-agbanye ọkụ ugboro 3, ngụkọta ọnụ ahịa akara bụ 10.

Function Interface 2 In the main interface, press the start button and stop button together for 3 seconds to enter the Function Interface 2, short press start button to view: Y/M/D, NJ ngwaọrụ, ọnụọgụ kachasị nke otu nchekwa fọdụrụnụ, ọnụọgụ nke otu akara.
Alarm State When the logger is operating,
Alarm disabled: Green LED flashes every 15 seconds and main interface displays . Alarm enabled: Red LED flashes every 15 seconds and main interface displays ×. No LED lights when the logger is in stopping state. Note: The red LED will also flash when the low voltage alarm appears. Users should save the data in time andreplace the battery.
Viewna data
Ndị ọrụ nwere ike view data na nkwụsị ma ọ bụ ọnọdụ arụ ọrụ.
View data dị na steeti nkwụsị: Jikọọ logger na PC, ọ bụrụ na ọkụ ọkụ na-egbuke egbuke n'oge a, a na-emepụta akụkọ PDF, ewepụla logger n'oge a. Mgbe emechara akụkọ PDF, ndị ọrụ nwere ike pịa PDF file ka view na mbupụ data site na ngwanrọ kọmputa.
View data na-arụ ọrụ na steeti: Jikọọ logger na PC, onye na-agba ọsọ ga-ewepụta akụkọ PDF maka data niile gara aga, n'otu oge ahụ, onye na-abanye na-aga n'ihu na-abanye data na ọ nwere ike ịmepụta akụkọ PDF na data ọhụrụ n'oge ọzọ. .
Alarm setting and result Single: The temperature (humidity) reaches or exceeds the set threshold. If the continuous alarm time is not less than the delay time, the alarm will be generated. If the reading returns to normal within the delay time, no alarm will occu.r If the delay time is 0s, an alarm will be generated immediately. Accumulate: The temperature (humidity) reaches or exceeds the set threshold. If the accumulated alarm time is not less than the delay time, the alarm will be generated.

Nkọwapụta

Okpomọkụ iru mmiri

Oke ọrụ
-30.0 20.1 -20.0 40.0 40.1 70.0
0% RH

UT330T Accuracy ±0.8 ±0.4 ±0.8
/

UT330TH Accuracy
±0.4
± 2.5% RH

UT330THC Accuracy
±0.4
± 2.5% RH

Protection degree Resolution Logging capacity Logging interval Unit/alarm setting
Start mode Logging delay
Device ID Alarm delay

IP65

/

/

Okpomọkụ: 0.1°C; iru mmiri: 0.1% RH

64000 setịpụ

10s 24h

Ngalaba ndabara bụ Celsius C. Ụdị mkpu gụnyere otu mkpu na akwakọba, ụdị ndabara bụ otu mkpu. Enwere ike ịgbanwe ụdị mkpu site na PC dị nro.

Pịa bọtịnụ ka ibido logger ma ọ bụ malite logger site na ngwanrọ (ozugbo / igbu oge / na oge a kapịrị ọnụ).
0min 240min, ọ dabara na 0 ma enwere ike ịgbanwe ya site na ngwa PC.

Enwere ike ịtọ ya na ngwanrọ PC na smartphone APP

0 255, ọ na-adabara na 0 ma enwere ike ịgbanwe ya site na ngwa PC.

0s 10h, ọ na-adabara na 0 ma nwee ike gbanwee site na ngwanrọ PC.

Screen off time Battery type
Mbupu data
Working time Working temperature & humidity Storage temperature

10s

CR2032

View na mbupụ data na PC software

View na mbupụ data na PC software na smartphone APP

140 days at an test interval of 15min (temperature 25)

-30°C ~ 70°C, 99%, non-condensable

-50°C ~ 70°C

EMC ọkọlọtọ: EN61326-1 2013.

Nlekọta
Battery replacement (Figure 4) Replace the battery with the following steps when the logger displays ” “.
Rotate the battery cover counter-clockwise. Install CR2032 battery and waterproof rubber ring(UT330TH) Install the cover in arrow direction and rotate it clockwise.

Na-ehicha osisi osisi

Jiri akwa dị nro ma ọ bụ sponge tinye obere mmiri, ncha, mmiri ncha hichaa osisi ahụ.

Ejila mmiri hichaa osisi ahụ ozugbo ka ị ghara imebi bọọdụ sekit.

Budata

Onyonyo 4

Budata ngwanrọ PC dịka ntuziaka ọrụ agbakwunyere si dị

Budata ngwanrọ PC site na gọọmentị website of UNI-T product center :http://www.uni-trend.com.cn

Wụnye

Pịa Setup.exe ugboro abụọ ka ịwụnye ngwanrọ

Nwụnye nke UT330THC gam akporo ama APP
1. Preparation Please install the UT330THC APP on the smartphone first.
2. Installation 2.1 Search “UT330THC” in Play Store. 2.2 Search “UT330THC” and download on UNI-T’s official websaịtị:
https://meters.uni-trend.com.cn/download?name=62 2.3 Scan the QR code on the right. (Note: APP versions may be updated without prior notice.) 3. Connection
Jikọọ UT330THC's Type-C njikọ na ekwentị chaja interface, wee mepee APP.

Akwụkwọ / akụrụngwa

UNI-T UT330T USB Data Logger [pdf] Ntuziaka UT330T, UT330T USB Data Logger, USB Data Logger, Data Logger

Ntụaka

• Akwụkwọ ntuziaka onye ọrụ