RENESAS E2 Emulator Chip Debugging Emulator

Zofotokozera:

• Dzina lazogulitsa: E2 Emulator, E2 Emulator Lite
• Chikalata chowonjezera: Buku la Wogwiritsa (Zolemba pa Kulumikizana kwa Zida za RISC-V MCU)
• Zida Zothandizira: R9A02G021
• Kukonzanso: Rev.1.00 Mar 2024

Malangizo Ogwiritsira Ntchito Zogulitsa

Chodzikanira ndi Zambiri Zalamulo:
Musanagwiritse ntchito E2 Emulator kapena E2 Emulator Lite, chonde bwereraniview Zambiri zamalamulo zoperekedwa ndi Renesas Electronics Corporation.
Ndikofunikira kutsatira malamulo ndi malamulo onse ogwiritsiridwa ntchito.

Kulumikizana kwa zida za RISC-V MCU:
Onani chikalata chowonjezera kuti mupeze malangizo enieni olumikizira zida za R9A02G021 zothandizidwa ndi emulator.

Kusintha ndi Kugwiritsa Ntchito Zinthu:
Osasintha, kusintha, kukopera, kapena kusintha mainjiniya gawo lililonse lazinthu za Renesas Electronics. Onetsetsani kuti zikutsatira zofunikira zonse zamalayisensi ndi malamulo oyendetsera katundu, kutumiza kunja, ndi kugawa katundu.

Zambiri zamalumikizidwe:
Ngati muli ndi mafunso okhudzana ndi malonda kapena kagwiritsidwe ntchito kake, chonde lemberani ofesi yogulitsa ya Renesas Electronics kuti ikuthandizeni.

FAQ

Q: Kodi ndingagwiritse ntchito E2 Emulator ndi zipangizo zina osati R9A02G021?
A: E2 Emulator idapangidwa kuti izithandizira zida za R9A02G021. Kuti mugwirizane ndi zida zina, chonde onani zomwe zaperekedwa ndi Renesas Electronics Corporation.

Q: Ndiyenera kuchita chiyani ndikafuna kupeza ziphaso zamaukadaulo a chipani chachitatu?
A: Ndi udindo wanu kudziwa ndi kulandira ziphaso zilizonse zofunika kuchokera kwa anthu ena kuti mugwiritse ntchito movomerezeka zinthu za Renesas Electronics. Onetsetsani kuti zikutsatira maufulu onse aukadaulo ndi zofunikira zamalamulo.

Q: Kodi ndingathe kupanganso kapena kubwereza buku la ogwiritsa ntchito?
A: Bukuli siliyenera kusindikizidwanso, kupangidwanso, kapena kubwereza popanda chilolezo cholembedwa kuchokera ku Renesas Electronics Corporation.

Zonse zomwe zili muzinthuzi, kuphatikizapo malonda ndi malonda, zimayimira zambiri zamalonda panthawi yofalitsidwa ndipo zikhoza kusintha ndi Renesas Electronics Corporation. popanda chidziwitso. Chonde review Zambiri zaposachedwa za Renesas Electronics Corporation. kudzera munjira zosiyanasiyana, kuphatikiza Renesas Electronics Corporation. webtsamba (http://www.renesas.com).

Zindikirani 

1. Mafotokozedwe a mabwalo, mapulogalamu ndi zidziwitso zina zokhudzana ndi chikalatachi zaperekedwa kuti ziwonetsetse magwiridwe antchito azinthu zama semiconductor ndi kugwiritsa ntchito kale.amples. Muli ndi udindo wonse pakuphatikizidwa kapena kugwiritsa ntchito zina zilizonse zamabwalo, mapulogalamu, ndi chidziwitso pamapangidwe azinthu kapena makina anu. Renesas Electronics imakana chiwongola dzanja chilichonse pakuwonongeka ndi kuwonongeka kulikonse komwe mungakumane nako kapena anthu ena chifukwa chogwiritsa ntchito mabwalo, mapulogalamu, kapena zambiri.
2. A Renesas Electronics akutsutsa mwatsatanetsatane zitsimikizo zilizonse zotsutsana ndi zomwe zikuphwanya kapena zonena zina zilizonse zokhudzana ndi ma patent, kukopera, kapena ufulu wina waluntha wa anthu ena, kapena chifukwa chogwiritsa ntchito zinthu za Renesas Electronics kapena zambiri zaukadaulo zomwe zafotokozedwa m'chikalatachi, kuphatikiza koma osati, kuchuluka kwazinthu, zojambula, ma chart, mapulogalamu, ma aligorivimu, ndi ntchito examples.
3. Palibe chilolezo, chofotokozera, chonenedwa kapena mwanjira ina, chomwe chimaperekedwa pansi pa zovomerezeka zilizonse, zokopera kapena ufulu wina waukadaulo wa Renesas Electronics kapena ena.
4. Mudzakhala ndi udindo wowona zilolezo zomwe zimafunidwa kuchokera kwa anthu ena, ndikupeza ziphaso zololeza kutumiza, kutumiza kunja, kupanga, kugulitsa, kugwiritsa ntchito, kugawa kapena kutaya zinthu zilizonse kuphatikiza zinthu za Renesas Electronics, ngati zingafunike.
5. Simudzasintha, kusintha, kukopera, kapena kusintha mainjiniya chilichonse cha Renesas Electronics, kaya chonse kapena pang'ono. Renesas Electronics imachotsa ngongole iliyonse pakuwonongeka kulikonse kapena kuwonongeka komwe mungakumane nako kapena anthu ena chifukwa chakusintha, kusinthidwa, kukopera kapena kubweza ukadaulo.
6. Zogulitsa za Renesas Electronics zimagawidwa molingana ndi magawo awiri awa: "Standard" ndi "High Quality". Zomwe akufunidwa pamtundu uliwonse wa Renesas Electronics zimatengera mtundu wazinthu zomwe zapangidwa, monga zasonyezedwera pansipa.
   • “Standard”: Makompyuta; zida zamaofesi; zida zoyankhulirana; zida zoyesera ndi zoyezera; zida zomvera ndi zowonera; zida zamagetsi zapanyumba; zida zamakina; zida zamagetsi zamagetsi; maloboti mafakitale; ndi zina.
   • "High Quality": Zida zoyendera (magalimoto, masitima apamtunda, zombo, etc.); kuwongolera magalimoto (magetsi apamsewu); zida zoyankhulirana zazikulu; machitidwe ofunikira azachuma; zida zowongolera chitetezo; ndi zina.
     Pokhapokha ngati zatchulidwa kuti ndi zodalirika kwambiri kapena zopangira nkhanza mu pepala la data la Renesas Electronics kapena chikalata china cha Renesas Electronics, Renesas Electronics sichinapangidwe kapena kuloledwa kuti chigwiritsidwe ntchito pazinthu kapena machitidwe omwe angawononge moyo wamunthu kapena kuvulazidwa kwa thupi (zida zopangira moyo wothandizira moyo kapena machitidwe; zoikamo opaleshoni; ndi zina zotero), kapena zingayambitse kuwonongeka kwakukulu kwa katundu (dongosolo lamlengalenga; zobwerezabwereza pansi pa nyanja; machitidwe olamulira mphamvu za nyukiliya; machitidwe oyendetsa ndege; makina opangira makina akuluakulu; zida zankhondo; etc.). Renesas Electronics imakana ngongole iliyonse pakuwonongeka kapena kuwonongeka kulikonse komwe mungakumane nako kapena wina aliyense chifukwa chogwiritsa ntchito chinthu chilichonse cha Renesas Electronics chomwe sichikugwirizana ndi pepala lililonse la Renesas Electronics, buku la ogwiritsa ntchito kapena chikalata china cha Renesas Electronics.
7. Palibe mankhwala a semiconductor omwe ali otetezeka. Mosasamala kanthu zachitetezo chilichonse kapena mawonekedwe omwe atha kukhazikitsidwa mu Renesas Electronics hardware kapena mapulogalamu apakompyuta, Renesas Electronics sadzakhala ndi mlandu uliwonse chifukwa cha chiopsezo kapena kuphwanya chitetezo, kuphatikiza koma osangokhala ndi mwayi uliwonse wosaloledwa kapena kugwiritsa ntchito chinthu cha Renesas Electronics. kapena dongosolo lomwe limagwiritsa ntchito mankhwala a Renesas Electronics. RENESAS ELECTRONICS SIKUTHANDIZA KAPENA KUTSIMIKIZIRA KUTI AMAKONZEZA ZINTHU ZAMA ELECTRONICS, KAPENA ZINTHU ZINA ZOMWE ZINACHITIKA POGWIRITSA NTCHITO ZOTSATIRA ZA ELECTRONICS ZA RENESAS SIZIDZACHITIKA KAPENA KUCHOKERA KU ZIVUNDU, ZOWUZA, MAVIRASI, KUWONONGA ZINTHU, KUCHITIKA ZINTHU, KUZIGWIRITSA NTCHITO, KUZIGWIRITSA NTCHITO, KUZIGWIRITSA NTCHITO. ). RENESAS ELECTRONICS IMASINTHA UDINDO ULIWONSE NDI ONSE KAPENA NTCHITO ZOCHOKERA KUCHOKERA KAPENA ZOKHUDZANA NDI NKHANI ZILI ZONSE. Kuwonjezela apo, MUKUGWIRITSA NTCHITO YOLOLOLEDWA NDI MALAMULO WOGWIRITSA NTCHITO, RENESAS ELECTRONICS AMADZIWA ZINTHU ZONSE NDI ZINSINSI ZONSE, KUSINTHA KAPENA ZOCHITIKA, PAMODZI NDI CHIKHALIDWE CHINO NDI ZINTHU ZILI ZOKHUDZA KAPENA ZOGWIRITSA NTCHITO, OSATI ZOKHUDZA ZOKHUDZA ZOKHUDZA ZOKHUDZA ZOKHUDZA ZOTHANDIZA. CHOLINGA ENA.
8. Mukamagwiritsa ntchito zinthu za Renesas Electronics, tchulani zidziwitso zaposachedwa kwambiri (mapepala, zolemba za ogwiritsa ntchito, zolemba zamagwiritsidwe ntchito, "Zolemba Zonse Zokhudza Kugwira ndi Kugwiritsa Ntchito Zida Zogwiritsa Ntchito Semiconductor" mu bukhu lodalirika, ndi zina zotero), ndikuwonetsetsa kuti zogwiritsiridwa ntchito zili mkati mwa migawo. yofotokozedwa ndi Renesas Electronics potengera ma ratings apamwamba, magetsi ogwiritsira ntchito voltage, mawonekedwe a kutentha, kuyika, ndi zina zotero. Renesas Electronics imatsutsa zolakwa zilizonse, kulephera kapena ngozi yomwe imabwera chifukwa chogwiritsa ntchito zinthu za Renesas Electronics kunja kwa mindandanda yotereyi.
9. Ngakhale Renesas Electronics imayesetsa kupititsa patsogolo kudalirika komanso kudalirika kwa zinthu za Renesas Electronics, zinthu za semiconductor zimakhala ndi mawonekedwe apadera, monga kulephera pamlingo wina komanso kulephera kwazinthu zina. Pokhapokha atasankhidwa kukhala chinthu chodalirika kwambiri kapena chopangira madera ovuta mu pepala la data la Renesas Electronics kapena chikalata china cha Renesas Electronics, zinthu za Renesas Electronics sizingagwirizane ndi kapangidwe kake ka radiation. Muli ndi udindo wokhazikitsa chitetezo kuti muteteze kuvulala, kuvulala kapena kuwonongeka chifukwa cha moto, komanso/kapena ngozi kwa anthu ngati zinthu za Renesas Electronics zalephereka kapena zitasokonekera, monga kapangidwe ka chitetezo cha hardware ndi mapulogalamu, kuphatikizapo koma osawerengeka ku redundancy, kuwongolera moto ndi kupewa kusagwira ntchito bwino, chithandizo choyenera cha ukalamba kapena njira zina zilizonse zoyenera. Chifukwa kuwunika kwa mapulogalamu a microcomputer okha ndizovuta kwambiri komanso kosatheka, muli ndi udindo wowunika chitetezo chazinthu zomaliza kapena makina opangidwa ndi inu.
10. Chonde lemberani ofesi yogulitsa ya Renesas Electronics kuti mumve zambiri zazachilengedwe monga kuyanjana kwachilengedwe kwa chinthu chilichonse cha Renesas Electronics. Muli ndi udindo wofufuza mosamala komanso mokwanira malamulo ndi malamulo okhudza kuphatikizika kapena kugwiritsiridwa ntchito kwa zinthu zolamulidwa, kuphatikizapo popanda malire, EU RoHS Directive, ndi kugwiritsa ntchito zinthu za Renesas Electronics motsatira malamulo ndi malangizowa. Renesas Electronics imachotsa udindo uliwonse pakuwonongeka kapena kutayika komwe kumachitika chifukwa chakusamvera kwanu malamulo ndi malamulo omwe akugwira ntchito.
11. Zogulitsa ndi matekinoloje a Renesas Electronics sizidzagwiritsidwa ntchito kapena kuphatikizidwa muzinthu zilizonse zomwe kupanga, kugwiritsa ntchito, kapena kugulitsa ndikoletsedwa pansi pa malamulo kapena malamulo anyumba kapena akunja. Mudzatsatira malamulo ndi malamulo aliwonse oyendetsera katundu omwe atulutsidwa ndi kutsogozedwa ndi maboma a mayiko aliwonse omwe ali ndi mphamvu pa maphwando kapena zochitika.
12. Ndi udindo wa wogula kapena wogawa zinthu za Renesas Electronics, kapena wina aliyense amene amagawa, kutaya, kapena kugulitsa kapena kusamutsa malonda kwa munthu wina, kuti adziwitse gulu lachitatu pasadakhale zomwe zili mkati ndi zomwe zafotokozedwa. mu chikalata ichi.
13. Chikalatachi sichidzasindikizidwanso, kupangidwanso kapena kutsatiridwa mwanjira iliyonse, yonse kapena mbali zake, popanda chilolezo cholembedwa cha Renesas Electronics.
14. Chonde lemberani ofesi yogulitsa ya Renesas Electronics ngati muli ndi mafunso okhudzana ndi zomwe zili mu chikalatachi kapena zinthu za Renesas Electronics.

(Chidziwitso1) "Renesas Electronics" monga momwe agwiritsidwira ntchito m'chikalatachi amatanthauza Renesas Electronics Corporation ndipo imaphatikizaponso mabungwe ake omwe amayendetsedwa mwachindunji kapena mwanjira ina.

(Chidziwitso2) "Renesas Electronics product(s)" amatanthauza chinthu chilichonse chopangidwa kapena chopangidwa ndi kapena cha Renesas Electronics.

Kusamala Kwambiri Pakusamalira Microprocessing Unit ndi Microcontrollers

Unit Products

Zolemba zotsatirazi zikugwira ntchito kuzinthu zonse za Microprocessing unit ndi Microcontroller unit zochokera ku Renesas. Kuti mumve zambiri za kagwiritsidwe ntchito kazinthu zomwe zalembedwa m'chikalatachi, onani magawo ofunikira a chikalatacho komanso zosintha zilizonse zaukadaulo zomwe zaperekedwa.

1. Kusamala motsutsana ndi Electrostatic Discharge (ESD)
   Mphamvu yamagetsi yamphamvu, ikalumikizidwa ndi chipangizo cha CMOS, imatha kuwononga chipata cha oxide ndipo pamapeto pake imasokoneza magwiridwe antchito a chipangizocho. Njira ziyenera kuchitidwa kuti muyimitse kupanga magetsi osasunthika momwe ndingathere, ndikuchotsa mwachangu zikachitika. Kuwongolera chilengedwe kuyenera kukhala kokwanira. Mukawuma, muyenera kugwiritsa ntchito humidifier. Izi ndizoyenera kupewa kugwiritsa ntchito ma insulators omwe amatha kupanga magetsi osasunthika mosavuta. Zipangizo za semiconductor ziyenera kusungidwa ndikunyamulidwa mu chidebe chotsutsana ndi malo amodzi, chikwama chotchinga chokhazikika kapena zinthu zoyendetsera. Zida zonse zoyesera ndi kuyeza kuphatikiza mabenchi ogwirira ntchito ndi pansi ziyenera kukhazikitsidwa. Wogwira ntchitoyo ayeneranso kumangidwa pansi pogwiritsa ntchito lamba pamanja. Zida za semiconductor siziyenera kugwidwa ndi manja opanda kanthu. Kusamala kofananako kuyenera kuchitidwa pama board osindikizidwa okhala ndi zida zokwezedwa za semiconductor.
2. Kukonza pa kuyatsa
   Mkhalidwe wa mankhwalawo sudziwika panthawi yomwe mphamvu imaperekedwa. Maiko a mabwalo amkati mu LSI ndi osadziwika ndipo maiko a zolembera ndi ma pini sakudziwika panthawi yomwe mphamvu imaperekedwa. Muzinthu zomalizidwa kumene chizindikiro chobwezeretsanso chimagwiritsidwa ntchito ku pini yokonzanso kunja, maiko a pini samatsimikiziridwa kuyambira nthawi yomwe mphamvu imaperekedwa mpaka kukonzanso kutsirizidwa. Momwemonso, zigawo za zikhomo muzinthu zomwe zimakonzedwanso ndi pa-chip-power-on reset ntchito sizikutsimikiziridwa kuyambira nthawi yomwe mphamvu imaperekedwa mpaka mphamvu ikufika pamlingo womwe kukonzanso kumatchulidwa.
3. Kulowetsa kwa chizindikiro panthawi yozimitsa magetsi
   Osalowetsa ma siginecha kapena kukoka mphamvu ya I/O pomwe chipangizocho chazimitsidwa. Jakisoni wapano womwe umabwera chifukwa cha kulowetsa kwa siginecha yotere kapena mphamvu yokoka ya I/O imatha kupangitsa kuti isagwire bwino ntchito ndipo mphamvu yamagetsi yomwe imadutsa pa chipangizocho panthawiyi ingayambitse kuwonongeka kwa zinthu zamkati. Tsatirani chitsogozo cha siginecha yolowera panthawi yozimitsa monga momwe zafotokozedwera muzolemba zanu.
4. Kugwira zikhomo zosagwiritsidwa ntchito
   Gwirani zikhomo zosagwiritsidwa ntchito molingana ndi malangizo omwe aperekedwa pogwira zikhomo zosagwiritsidwa ntchito m'bukuli. Zikhomo zolowera zazinthu za CMOS nthawi zambiri zimakhala m'malo ovuta kwambiri. Pogwira ntchito ndi pini yosagwiritsidwa ntchito pamalo otseguka, phokoso lowonjezera la electromagnetic limapangidwira pafupi ndi LSI, kuwombera komwe kumagwirizanako kumayenda mkati, ndipo kusokonezeka kumachitika chifukwa cha kuzindikira kwabodza kwa pini ngati chizindikiro cholowetsa. kukhala zotheka.
5. Zizindikiro za wotchi
   Mukayika kukonzanso, ingotulutsani mzere wokhazikitsanso chizindikiro cha wotchiyo chikakhazikika. Mukasintha chizindikiro cha wotchi panthawi ya pulogalamu, dikirani mpaka chizindikiro cha wotchiyo chikhazikike. Pamene chizindikiro cha wotchi chimapangidwa ndi resonator yakunja kapena kuchokera ku oscillator yakunja panthawi yokonzanso, onetsetsani kuti mzere wokonzanso umangotulutsidwa pambuyo pa kukhazikika kwathunthu kwa chizindikiro cha wotchi. Kuonjezera apo, mukamasinthira ku chizindikiro cha wotchi chomwe chimapangidwa ndi resonator yakunja kapena ndi oscillator yakunja pamene pulogalamu ikuchitika, dikirani mpaka chizindikiro cha wotchiyo chikhale chokhazikika.
6. Voltage application waveform pa pini yolowera
   Kusokonekera kwa ma waveform chifukwa cha phokoso lolowera kapena mafunde owoneka bwino angayambitse kusagwira ntchito. Ngati kulowetsa kwa chipangizo cha CMOS kumakhala pakati pa VIL (Max.) ndi VIH (Min.) chifukwa cha phokoso, chifukwaampndi, chipangizo mwina wonongeka. Samalani kuti muteteze phokoso loyankhulana kuti lilowe mu chipangizochi pamene mulingo wolowera wakhazikika, komanso mu nthawi ya kusintha pamene mlingo wolowera umadutsa pakati pa VIL (Max.) ndi VIH (Min.).
7. Kuletsa kupeza ma adilesi osungidwa
   Kufikira kumaadiresi osungidwa ndikoletsedwa. Ma adilesi osungidwa amaperekedwa kuti awonjezere ntchito zamtsogolo. Osapeza ma adilesi awa chifukwa kugwira ntchito moyenera kwa LSI sikutsimikizika.
8. Kusiyana kwa mankhwala
   Musanasinthe kuchokera ku chinthu china kupita ku china, mwachitsanzoample kwa chinthu chokhala ndi gawo lina la nambala, tsimikizirani kuti kusintha sikungabweretse mavuto. Makhalidwe a microprocessing unit kapena microcontroller unit katundu m'gulu lomwelo koma kukhala ndi gawo losiyana nambala akhoza kusiyana malinga ndi kukula kwa kukumbukira mkati, mapangidwe apangidwe, ndi zinthu zina, zomwe zingakhudze mitundu yosiyanasiyana yamagetsi, monga makhalidwe, m'mphepete mwa ntchito, chitetezo ku phokoso, ndi kuchuluka kwa phokoso lotulutsa. Mukasintha kukhala chinthu chokhala ndi nambala yosiyana, yesani kuyesa kuwunika kwadongosolo la chinthu chomwe mwapatsidwa.

Terminology
Mawu ena apadera omwe agwiritsidwa ntchito m'buku la ogwiritsa ntchito afotokozedwa pansipa.

Host makina
Izi zikutanthauza munthu kompyuta ntchito kulamulira emulator.

Dongosolo la ogwiritsa ntchito
Izi zikutanthawuza kuti wogwiritsa ntchito akugwiritsa ntchito MCU yomwe iyenera kusinthidwa.

Pulogalamu ya ogwiritsa ntchito
Izi zikutanthauza kuti pulogalamuyo iyenera kusinthidwa.

Pulogalamu yamapulogalamu
M'chikalatachi, izi zikuwonetsa Renesas Flash Programmer yomwe ingagwiritsidwe ntchito ndi E2 kapena E2 Lite.

Emulator
Mu chikalata ichi, izi zikutanthauza E2 kapena E2 Lite.

Zathaview

Zathaview E2 Emulator ndi E2 Emulator Lite
M'chikalatachi, tikufotokoza 'E2 Emulator' ngati 'E2' ndi 'E2 Emulator Lite' ngati 'E2 Lite'. The E2 ndi E2 Lite ndi pa-chip debugging emulators kwa Renesas ' main MCUs.

E2 Lite ndi zida zachitukuko zotsika mtengo kwambiri zomwe zimapereka ntchito zowongolera. E2 imayendetsa kutsitsa kothamanga kwambiri mpaka kuwirikiza kawiri kuchuluka kwa E2 Lite. Kuphatikiza apo, E2 imatha kupereka mphamvu zomwe zimasinthika kuchokera ku 1.8 V mpaka 5.0 V pamipata ya 0.1-V. Monga chida chachitukuko, E2 imalola kukonza zolakwika kwambiri kuposa E2 Lite. E2 ndi E2 Lite imathanso kugwira ntchito ngati Flash Programmer.

Kukonzekera kwa E2/E2 Lite Manual

Buku la E2/E2 Lite lili ndi izi.

• Buku la E2 Emulator User
• Buku la E2 Emulator Lite
• E2 Emulator, E2 Emulator Lite Zowonjezera Document for User's Manual

Onetsetsani kuti mwawerenga buku la wogwiritsa ntchito musanagwiritse ntchito E2 kapena E2 Lite.

1. E2 emulator wosuta buku
   Buku la wogwiritsa ntchito emulator E2 lili ndi izi:
   • Zithunzi za E2
   • E2 hardware specifications
   • Kulumikizana kwa E2 ndi makina ochitira ndi makina ogwiritsira ntchito
2. Buku la ogwiritsa la E2 Emulator Lite
   Buku la ogwiritsa la E2 Emulator Lite lili ndi izi:
   • Zithunzi za E2 Lite
   • Mafotokozedwe a hardware a E2 Lite
   • Kulumikizana ndi E2 Lite ndi makina ogwiritsira ntchito ndi makina ogwiritsira ntchito
3.  E2 Emulator, E2 Emulator Lite Zowonjezera Zolemba za Buku la Wogwiritsa (Zolemba pa Kulumikizana kwa Zida za RISC-V MCU) (chikalatachi)
   E2 Emulator, E2 Emulator Lite Zowonjezera Zolemba Zolemba Zogwiritsa Ntchito (Zolemba pa Kulumikizana kwa RISC-V MCU Devices) amafotokoza zambiri zofunika pakupanga kwa hardware monga kulumikizana kale.amples ndi mawonekedwe ozungulira.
4. Renesas Flash Programmer Flash memory programming software Buku Logwiritsa Ntchito
   Renesas Flash Programmer Flash memory programming software User's Manual imalongosola ndondomeko ya pulogalamuyo ndi njira yogwirira ntchito ya Renesas Flash Programmer.
   • Pakusintha kosintha kwa E2 kapena E2 Lite emulator debugger, onani njira yothandizira pa studio ya e2.

Kukonzekera
Pezani malo ophatikizika otukuka (IDE) ndi mapulogalamu ena ofunikira kuchokera pamalumikizidwe otsatirawa URL ndi kuwayika iwo pa makina khamu.
https://www.renesas.com/development-tools

Zida Zothandizira

Gulu 1.1 Mndandanda wa Zida Zothandizira

Chida Chothandizira	E2		E2 Lite
	cJTAG Ine/F	SCI	cJTAG Ine/F	SCI
R9A02G021	DBG	PRG	DBG	PRG

DBG: Itha kugwiritsidwa ntchito pakuwongolera, PRG: Itha kugwiritsidwa ntchito pakupanga mapulogalamu

Kupanga Makina Ogwiritsa Ntchito

Kulumikiza Emulator ndi User System
Kulumikiza emulator, cholumikizira kwa wosuta dongosolo mawonekedwe chingwe ayenera wokwera pa dongosolo wosuta.
Popanga makina ogwiritsira ntchito, werengani gawo ili la bukhuli ndi Buku la Wogwiritsa: Zida za MCU zoperekedwa.

Kuyika Cholumikizira pa User System
Table 2.1 ndi Table 2.2 mndandanda analimbikitsa zolumikizira ndi wosuta dongosolo mawonekedwe zingwe kwa emulator, motero.

Table 2.1 Zolumikizira Zovomerezeka

Cholumikizira	Type Number	Wopanga	Zofotokozera
20-pin (1.27-mm pitch pitch) cholumikizira	FTSH-110-01-L-DV-K	Samtec	20-pin surface-mount technology (SMT) yowongoka
20-pin (1.27-mm pitch pitch) cholumikizira	FTSH-110-01-L-DV-007-K (Cholumikizira popanda pini 7)	Samtec	20-pin surface-mount technology (SMT) yowongoka
10-pin (1.27-mm pitch pitch) cholumikizira	FTSH-105-01-L-DV-K	Samtec	10-pini SMT mtundu wowongoka
10-pin (1.27-mm pitch pitch) cholumikizira	FTSH-105-01-L-DV* (popanda chizindikiro chofananira ndi malo a cholumikizira; chophimba chophimba)	Samtec	10-pini SMT mtundu wowongoka
10-pin (1.27-mm pitch pitch) cholumikizira	FTSH-105-01-L-DV-007-K (Cholumikizira popanda pini 7)	Samtec	10-pini SMT mtundu wowongoka

Zindikirani: Mukamagwiritsa ntchito cholumikizira popanda cholembera cholembera (mtundu wa keying-shroud), samalani ndi njira yoyika chingwecho.

Table 2.2 User System Interface Cables 

Mtundu wa Chingwe	Type Number	E2	E2 Lite
20-pini mpaka 20-mapini chingwe* (kwa cholumikizira cha mapini 20 (1.27-mm pitch pitch))	RTE0T00020KCAC0000J	Amabwera ndi mankhwala	Zogulitsidwa padera
20-pini mpaka 10-pini chingwe (kwa cholumikizira cha mapini 20 (1.27-mm pitch pitch))	RTE0T00020KCAC1000J	Zogulitsidwa padera	Zogulitsidwa padera

Zindikirani: Chingwe cha pini 20 mpaka 20 chimatha kulumikizidwa ku cholumikizira chopanda mapini 10 (1.27-mm pitch pitch); pochita izi, komabe, yang'anani ntchito za pini ndikusamala za momwe mungayikitsire chingwe.

Only kugwirizana emulator pambuyo kutsimikizira kuti palibe mismatches wa mayikidwe pa wosuta dongosolo doko cholumikizira. Kulumikizana kolakwika kumapangitsa makina opangira, emulator, ndi makina ogwiritsira ntchito kutulutsa utsi kapena kuyaka moto.

Kulumikiza Cable System Interface Cable ku 20-Pin Connector Chithunzi 2.1 chikuwonetsa momwe mungalumikizire chingwe cholumikizira makina ogwiritsira ntchito ku cholumikizira cha 20-pin.

CHENJEZO
Zolemba pa kuyika ndi kuchotsa cholumikizira:

Pamene kulumikiza kapena kusagwirizana wosuta-dongosolo mawonekedwe chingwe ndi emulator kapena dongosolo wosuta, gwirani cholumikizira chivundikirocho kumapeto kwa chingwe. Kukoka chingwe chokha kumawononga waya.
Komanso, dziwani kuti chingwe cholumikizira makina ogwiritsira ntchito chili ndi njira yomwe chiyenera kuyikidwamo. Ngati chingwecho chikugwirizanitsidwa molakwika, chikhoza kuwonongeka.

Lembani Ntchito za Cholumikizira pa Makina Ogwiritsa Ntchito

1. 20-Pini ndi 10-Pini Cholumikizira
   Chithunzi 2-2 chikuwonetsa zolumikizira za 20-pin ndi 10-pin (1.27-mm pitch).

Table 2.3 wonetsani ntchito zamapini za cJTAG ma interfaces, motero.

Table 2.3 Pin Ntchito za cJTAG Chiyanjano cholumikizira

Pin Ayi.	Chizindikiro	Mayendedwe*1	Zindikirani
1	Chithunzi cha VCC	–	Magetsi
2	Mtengo wa TMSC	Ine/O	Za cJTAG
3	GND	–
4	Mtengo wa TCCK	Zolowetsa	Za cJTAG
5	GND	–
6	TxD0 (P302)	Zotulutsa	Za SCI
7	NC	–
8	RxD0 (P303)	Zolowetsa	Za SCI
9	Zotsatira UCON	–	Lumikizani chizindikiro ichi pansi pa makina ogwiritsa ntchito. Izo ntchito kutsimikizira kugwirizana pakati emulator ndi wosuta dongosolo.
10	RES	Ine/O	Kukhazikitsanso dongosolo la ogwiritsa ntchito
11*2	NC	–
12*2	NC	–
13*2	NC	–
14*2	NC	–
15*2	GND	–
16*2	NC	–
17*2	GND	–
18*2	NC	–
19*2	GND	–
20*2	NC	–

MFUNDO

1. Lowetsani kapena kutulutsa kuchokera ku makina ogwiritsa ntchito.
   "Lowetsa" amatanthauza athandizira kuchokera emulator kuti wosuta dongosolo ndi "linanena bungwe" amatanthauza linanena bungwe wosuta dongosolo kwa emulator.
2. Ngati cholumikizira cha pini 10 chayikidwa pamakina ogwiritsira ntchito, zikhomo 11 mpaka 20 sizigwiritsidwa ntchito.

Dera lovomerezeka pakati pa Cholumikizira ndi MCU
Gawoli likuwonetsa mabwalo ovomerezeka olumikizirana pakati pa cholumikizira ndi MCU. Kuti mudziwe zambiri za kasamalidwe ka ma siginoloji, onani gawo 2.5, Zolemba pa Kulumikizana.

cJTAG Chiyanjano cholumikizira
Chithunzi 2.3 chikuwonetsa dera lolimbikitsidwa kuti lilumikizidwe kudzera mu cJ yokhayoTAG malumikizidwe.

ZINDIKIRANI
Mafotokozedwe amatha kusiyana ndi cholinga cha MCU. Tsimikizirani tsatanetsatane wa mapini omwe amagwiritsidwa ntchito popanga pulogalamu ya flash mu bukhu la wogwiritsa ntchito la MCU yoperekedwa.

Zolemba pa Kulumikizana
Njira zama waya pakati pa cholumikizira ndi MCU ziyenera kukhala zazifupi momwe zingathere (mkati mwa 50 mm ndikulimbikitsidwa). Osalumikiza mizere yolumikizira pakati pa cholumikizira ndi MCU ku mizere ina yama siginecha pa bolodi.
Pakuti kusamalira zikhomo pamene emulator si ntchito, tchulani Buku la Wogwiritsa: Hardware kwa MCU anapatsidwa.

RES Pin
The emulator amagwiritsa RES pini.
Ngati makina ogwiritsira ntchito akuphatikiza dera lokhazikitsira malingaliro a ogwiritsa ntchito, chizindikiro chotuluka kuchokera kugawo lokhazikitsiranso chiyenera kulumikizidwa ndi pini ya RES ya cholumikizira kudzera pa buffer-otolera yotseguka monga momwe tawonetsera pansipa. Ngati palibe dera lokhazikitsiranso, pini ya RES kuchokera ku cholumikizira iyenera kulumikizidwa mwachindunji ndi pini ya RES ya MCU.

Voltage pa mzere wa RES ayenera kukwaniritsa mawonekedwe amagetsi a chipangizocho ndikukwera osapitirira 9 ms.

MD Pin
Kuti mupitilize kupanga pulogalamu ya serial pogwiritsa ntchito pulogalamu yowunikira, yambitsani MCU mu UART (SAU) boot mode.

Ikani ma switch kuti musinthe mlingo wa MD pin pa makina ogwiritsira ntchito monga momwe akufunira (onani Chithunzi 2-5).
Pamene mudzakhala ntchito MD pini kusankha UART (SAU) jombo mode, ikani MD pini pa mlingo otsika.
Pamene mudzakhala mukugwiritsa ntchito MD pin kuti musankhe single-chip mode kuti mugwiritse ntchito kapena kusokoneza pulogalamu ya osuta, ikani pin MD pamlingo wapamwamba.

Zotsutsa zokoka zimayikidwa pazikhomo za MD za ma MCU ambiri. Onani Buku la Wogwiritsa Ntchito: Zida za MCU zomwe zapatsidwa kuti zitsimikizire ngati choletsa chokokera chayikidwa pa MD pini ya MCU.

GND
Zikhomo za cholumikizira cholembedwa kuti "GND" ziyenera kukhala pamtunda wofanana ndi pini ya VSS ya MCU.

Chithunzi cha VCC
Lumikizani VCC ya cholumikizira ku VCC (magetsi) a makina ogwiritsa ntchito.
Ntchito emulator mkati mphamvu kotunga voltage wa 1.8 V kuti 5.5 V ndi mkati ntchito voltagmndandanda wa MCU ndi cJTAG.

Mphamvu ikaperekedwa kwa wogwiritsa ntchito kuchokera kwina kusiyapo emulator, E2/E2 Lite imagwiritsa ntchito mphamvu zotulutsa zomaliza ndi zoyambira zoyambira za emulator.

• E2: 3.3 V: pafupifupi 20 mA, 5.0 V: pafupifupi 40 mA
• E2 Lite: 3.3 V: pafupifupi 20 mA, 5.0 V: pafupifupi 40 mA

E2/E2 Lite imatha kupereka mphamvu ku njira yosavuta yowunikira.

• E2: Itha kupereka mphamvu ya 1.8 V mpaka 5.0 V, mpaka 200 mA.
• E2 Lite: Itha kupereka mphamvu ya 3.3 V, mpaka 200 mA.

Mukamagwiritsa ntchito magetsi a E2 kapena E2 Lite, onani voltage zomwe zikuperekedwa kwa ogwiritsa ntchito chifukwa izi zimatengera chilengedwe.

Mphamvu yamagetsi yochokera ku E2/E2 Lite imadalira mtundu wamagetsi a USB a makina ochitirako, ndipo motero, kulondola sikutsimikizika. Polemba pulogalamu yomwe imafuna kudalirika, musagwiritse ntchito magetsi a E2 / E2 Lite. Gwiritsani ntchito mphamvu yokhazikika, yosiyana kwa wogwiritsa ntchito. Monga mapulogalamu polemba pulogalamu pakupanga zinthu zambiri, gwiritsani ntchito Renesas Flash Programmer.

Kuti mudziwe zambiri za pulogalamu ya pulogalamuyo, onani zotsatirazi:
Renesas Flash Programmer: https://www.renesas.com/RFP

MCU ikasinthidwa kukhala mphamvu yotsika, dera lowongolera mkati likupitilizabe. Izi zimapangitsa kuti MCU ijambule magetsi ochulukirapo kuposa momwe zalembedwera mu mawonekedwe a DC a MCU yomwe mukufuna.

CHENJEZO

Chenjezo pakuyatsa/Kuzimitsa Mphamvu:
Popereka mphamvu, onetsetsani kuti palibe akabudula pakati pa Vcc ndi GND. Ingolumikizani E2 / E2 Lite mutatsimikizira kuti palibe cholakwika cholumikizira pa cholumikizira doko la ogwiritsa ntchito. Kulumikizana kolakwika kumapangitsa makina osungira, E2/E2 Lite, ndi makina ogwiritsira ntchito kutulutsa utsi kapena kuyaka moto.

RxD9 ndi TxD9 Pins (Flash Programming kudzera pa SCI)
Memory flash ikakonzedwa kudzera pa SCI, mapini a RxD9 ndi TxD9 ayenera kulumikizidwa ndi emulator. Kwa ma MCU omwe ma RxD9 ndi TxD9 atha kugawidwa pamapini angapo, onani

Zolemba: Zida za MCU zoperekedwa kuti zitsimikizire kuti ndi zipi zomwe zimagwiritsidwa ntchito poyambira.

Madera Amkati a Emulator

1. Mayendedwe Amkati a E2
   Chithunzi 2-6 ndi Chithunzi 2-7 motsatana chikuwonetsa mabwalo amkati akusintha kwazinthu C ndi D za E2. Zilembo zomwe zili kumapeto kwa seriyo No. zolembedwa pagawo lalikulu la E2 zikuwonetsa kukonzanso kwazinthu.

Chithunzi 2-6 Magawo Amkati a E2 (Rev. C)

Zindikirani:
Ngati cholumikizira cha pini 10 chayikidwa pamakina ogwiritsira ntchito, zikhomo 11 mpaka 20 sizigwiritsidwa ntchito.

Chithunzi 2-7 Madera Amkati a E2 (Rev. D)

ZINDIKIRANI
Ngati cholumikizira cha pini 10 chayikidwa pamakina ogwiritsira ntchito, zikhomo 11 mpaka 20 sizigwiritsidwa ntchito.

Mayendedwe Amkati a E2 Lite
Chithunzi 2-8 chikuwonetsa mabwalo amkati a E2 Lite.

Zolemba pa Kugwiritsa Ntchito

Kuyatsa/Kuzimitsa Mphamvu
Sinthani mphamvu ya emulator ndi dongosolo wosuta kutsatira ndondomeko pansipa.

Pamene Kupereka Mphamvu Kwapadera Kugwiritsidwa Ntchito Kwa Wogwiritsa Ntchito

1. Onetsetsani kuti mphamvu yazimitsa.
   Onetsetsani kuti makina ogwiritsira ntchito atsekedwa.
2. Lumikizani makina ogwiritsa ntchito.
   Lumikizani emulator ndi wosuta dongosolo ndi wosuta-dongosolo mawonekedwe chingwe.
3. Lumikizani makina olandila ndikuyatsa emulator.
   Lumikizani emulator ndi makina olandila ndi chingwe cha USB. E2/E2 Lite imayatsidwa polumikiza chingwe cha USB.
4. Kukhazikitsa emulator debugger kapena mapulogalamu mapulogalamu.
   Kukhazikitsa emulator debugger kapena mapulogalamu mapulogalamu.
5. Yatsani makina ogwiritsa ntchito.
   Yatsani makina ogwiritsa ntchito.
6. Lumikizani debugger ya emulator kapena pulogalamu yamapulogalamu ku emulator.
   Kulumikizana kungasiyane kutengera mapulogalamu.

1. Chotsani emulator kuchokera ku emulator debugger kapena pulogalamu yamapulogalamu.
   Kulumikizika kungasiyane kutengera mapulogalamu.
2. Zimitsani makina ogwiritsa ntchito.
   Zimitsani makina ogwiritsa ntchito.
3. Tsekani emulator debugger kapena mapulogalamu mapulogalamu.
   Tsekani emulator debugger kapena mapulogalamu mapulogalamu.
4. Zimitsani emulator ndikudula emulator.
   Chotsani chingwe cha mawonekedwe a USB kuchokera ku emulator. E2/E2 Lite imazimitsidwa podula chingwe cha mawonekedwe a USB.
5. Chotsani makina ogwiritsa ntchito.
   Chotsani chingwe cholumikizira mawonekedwe a ogwiritsa ntchito.

CHENJEZO
Zolemba pa User System Power Supply:

Pamene mphamvu ya makina ogwiritsira ntchito ikugwiritsidwa ntchito, musazimitse makina ogwiritsira ntchito kapena kuchotsa chingwe cha USB.
Dongosolo la ogwiritsa ntchito litha kuonongeka chifukwa cha kutayikira kwapano.

Pamene Mphamvu imaperekedwa kwa Wogwiritsa System kuchokera ku Emulator

1. Lumikizani makina ogwiritsa ntchito.
   Lumikizani emulator ndi wosuta dongosolo ndi wosuta-dongosolo mawonekedwe chingwe.
2. Lumikizani makina olandila ndikuyatsa emulator.
   Lumikizani emulator ndi makina ogwiritsira ntchito ndi chingwe cha USB cholumikizira, kenako yatsani emulator.
3. Yambitsani debugger ya emulator.
   Kukhazikitsa debugger emulator ndi kusankha kolowera magetsi kwa wosuta dongosolo.
   Pansi pa [Mphamvu] pa [Zikhazikiko Zolumikizira], sankhani [Inde] ya [Power Target From The Emulator (MAX 200mA)]. Onani gawo 3.3, Zolemba pa Kugwiritsa Ntchito Emulator Debugger, momwe mungatsegule zenera la [Debug Configurations].
4. Lumikizani debugger ya emulator kapena pulogalamu yamapulogalamu ku emulator.
   Kulumikizana kungasiyane kutengera mapulogalamu.

1. Chotsani emulator kuchokera ku emulator debugger kapena pulogalamu yamapulogalamu. Kulumikizika kungasiyane kutengera mapulogalamu.
2. Tsekani emulator debugger kapena mapulogalamu mapulogalamu.
   Tsekani emulator debugger kapena mapulogalamu mapulogalamu.
3. Zimitsani emulator ndikudula emulator.
   Chotsani chingwe cha mawonekedwe a USB kuchokera ku emulator, kenako zimitsani emulator.
4. Chotsani makina ogwiritsa ntchito.
   Chotsani chingwe cholumikizira mawonekedwe a ogwiritsa ntchito.

Ntchito Yopereka Mphamvu ya E2/E2 Lite
E2/E2 Lite imatha kupereka mphamvu ku njira yosavuta yowunikira.

• E2: Itha kupereka mphamvu ya 1.8 V mpaka 5.0 V, mpaka 200 mA.
• E2 Lite: Itha kupereka mphamvu ya 3.3 V, mpaka 200 mA.

Mukamagwiritsa ntchito magetsi a E2 kapena E2 Lite, onani voltage zomwe zikuperekedwa kwa ogwiritsa ntchito chifukwa izi zimatengera chilengedwe.

Zolemba pakugwiritsa ntchito Emulator Debugger
Gawoli likufotokoza momwe mungakhazikitsire zenera la [Debug Configurations] la studio ya e2. Kuti mutsegule zenera la [Debug Configurations], dinani [Run] → [Debug Configurations…] kapena muvi wolozera pansi pafupi ndi icon→ [Zosintha Zosintha…].

Zolemba pa Kulumikiza Emulator Debugger

1. Bwezerani dziko
   Pa kulumikiza debugger emulator, ndi emulator amakhalabe otsika mlingo linanena bungwe pa RES # pini wa MCU ndi kuika MCU mu mode OCD.
2. Njira yoyambira
   Pamene emulator debugger chikugwirizana, gwirani zikhomo pa dongosolo wosuta kuti mode oyambitsa wa MCU ndi single-chip mode.
   Mu single-chip mode, MD pini ili pamlingo wapamwamba. Kulumikizana kolondola kwa emulator debugger sikutheka mu SCI boot mode.
3. Kuthetsa vuto pambuyo polembanso nambala ya ID
   Ngati nambala ya ID (kaundula ya OSIS) yalembedwanso, lowetsani ID yatsopano.
   Apa, nambala ya ID yoti mulowetse ikutanthauza mtengo woti mulowe mu [ID Code (Bytes)] pansi pa [Lumikizani] patsamba la [Zikhazikiko Zolumikizira].
4. Kulowetsa lamulo la ALeRASE la nambala ya ID (Kwa ena osati banja la RA8)
   Ngati lamulo la ALeRASE (FFFFFFFFFFFFFFFFFF45534152654C41) lalowetsedwa mu [ID Code (Bytes)] pansi pa [Connection] pa [Connection Settings] tsamba la [Connection Settings], code flash memory, data flash memory ndi zoikirapo zosankha zidzafufutika pamene emulator debugger ikugwirizana.
   Kuti mumve zambiri pakulowa lamulo la ALeRASE, onani Zokonda Zolumikizira za E2/E2 Lite (RA) munjira yothandizira pa studio ya e2.
   Pamikhalidwe yomwe lamulo la ALeRASE limagwiritsidwa ntchito, tchulani Buku la Wogwiritsa: Hardware ya MCU yopatsidwa. Ngati lamulo la ALeRASE lalowetsedwa ndiye kuti emulator debugger imalumikizidwa pomwe lamulo silikugwiritsidwa ntchito pa MCU, uthenga wolakwika "Walephera kufufuta kukumbukira kwa flash ndi ID pakuchotsa kukumbukira konse." ikuwonetsedwa ndipo njira yolumikizira imayimitsidwa.
5. Kuthamanga kwa kulumikizana
   Kuthamanga kwa kugwirizana kwa emulator ku bolodi chandamale kumatchulidwa mkati mwazotsatira zapamwamba-malire.
   • cJTAG (E2): 8250 kHz
   • cJTAG (E2 Lite): 1000 kHz yokhazikika

[Auto] ikasankhidwa, liwiro lalikulu lolumikizidwa lidzakhazikitsidwa yokha.

Zolemba pa Ntchito Yowongolera Zomwe Zimakhudza Kukonzanso kwa Flash Memory

"Ntchito yowonongeka yomwe imaphatikizapo kukonzanso kukumbukira kwa flash" imatanthawuza ntchito zotsatirazi za emulator debugger.

• Kutsitsa deta ku flash memory
• Kugwiritsa ntchito pulogalamu yopumira mu flash memory
  • Kukhazikitsa ndi kuletsa breakpoints
  • Kukhazikitsa kapena kukhazikitsa mapulogalamu kuchokera pa breakpoint
  • Pogwiritsa ntchito ntchito ya "Run to Line" kuchokera kumalo komwe kupuma kunakhazikitsidwa
    1. Pulogalamu ya reprogramming flash memory
       Popeza emulator debugger imathandizira kukonza zolakwika zomwe zimaphatikizapo kukonzanso kukumbukira kwa flash, emulator imalemba pulojekiti yokonzanso kukumbukira kwa flash ku pa-chip SRAM ndikuchita pulogalamuyo kuti ikonzenso kukumbukira kwa flash. Pambuyo pokonzanso flash memory, debugger ya emulator imabwezeretsa pa-chip SRAM pamalo ake oyamba.
    2. Kopita kugawika kwa pulogalamu reprogramming flash memory
       Mwachikhazikitso, pulogalamu yokonzanso kukumbukira kwa flash imaperekedwa ku malo a 4-Kbyte kuchokera ku adiresi yomwe dera la SRAM0 limayambira (kapena adiresi yomwe dera la SRAMHS limayambira pazida zomwe sizikuphatikizapo dera la SRAM0). Ngati malo omwe agawidwe akusankhidwiratu sakupezeka chifukwa cha zochunira zachitetezo kapena kusamutsa kwa DMAC/DTC*, lowetsani adilesi yoyambira ya malo omwe alipo mu pa-chip RAM m'mayunitsi a 1000h byte motsutsana ndi [Adilesi Yoyambira Yantchito ya RAM] pansi pa [Kung'anima] pa [Debug Tool Zikhazikiko] tsamba la tabu la emulator debugger.
       Zindikirani: DMAC kapena DTC ipitiliza kugwira ntchito ngakhale panthawi yopuma. Samalani kuti kochokera kapena kopita ku DMAC kapena DTC sikuli mkati mwa ma adilesi a RAM yomwe ikugwira ntchito komwe pulogalamuyo idzagawidwe.
    3. Imasokoneza ndikukhazikitsanso pakuchita pulogalamu ya reprogramming flash memory
       Zosokoneza zina osati zosokoneza zomwe sizingasokonezeke ziyenera kubisika pamene pulogalamu yokonzanso flash memory ikuchitidwa. Komanso, kuti pulogalamu ya reprogramming flash memory ikwaniritsidwe bwino, mbendera zonse zosokoneza zomwe zakhazikitsidwa zisanachitike pulogalamuyo zimachotsedwa.
       Ngati kusokoneza kosasunthika kukuchitika, emulator ikupitiriza kuyendetsa pulogalamu yokonzanso kukumbukira kukumbukira. Ngati kukonzanso kumachitika pomwe pulogalamu yokonzanso flash memory ikuchitidwa, emulator imawonetsa uthenga wolakwika ndikusiya kukonza. Popeza kutero kungawononge zomwe zili mu flash memory, musagwiritse ntchito reset pomwe pulogalamuyo ikugwira ntchito.
    4. Zoyenera kutsitsa deta ku flash memory kukhalapo
       MCU ikakwaniritsa zonse zotsatirazi, kutsitsa kwa data ku flash memory kumatha kupitilira.
       • Code flash memory ya MCU ili mu kuwerenga.
       • Mafupipafupi a wotchi yadongosolo (ICLK) ya MCU ndi 1 MHz kapena kupitilira apo.
       • MCU ili mumayendedwe othamanga kwambiri kapena othamanga kwambiri.
         Zindikirani: Kwa [Koloko] patsamba la [Zikhazikiko Zolumikizira] la chosinthira emulator, [Inde] ikasankhidwa [Inde] yasankhidwira [Chilolezo cha Wotchi yosintha polemba pa-chip Flash Memory], zinthu (b) ndi (c) zitha kuchotsedwa.
         Ngati deta idatsitsidwa kuti ikumbukire kukumbukira pomwe chikhalidwe chilichonse sichikukhutitsidwa, emulator imawonetsa uthenga wolakwika ndikusiya kukonza. Zikatero, yambitsaninso kutsitsa kwa data kuti mukumbukire CPU ikasinthidwa kapena kulumikizanso chosinthira emulator pambuyo poyambiranso.viewkuyika zoikamo zake.
    5. Kufikira zenera ntchito
       Mukamagwiritsa ntchito zenera lofikira la MCU, ingokonzanso kukumbukira kwa flash m'dera lomwe lafotokozedwa kuti mufike.
    6. Ntchito yoteteza Flash Read
       Ntchito yoteteza kung'anima yowerengera siyenera kuyatsidwa panthawi yakusintha. Kutenga kuchokera kumadera omwe akhazikitsidwa kuti atetezedwe ku flash ndikotheka koma kuwerenga sikuli. Ngati kuwerengedwa kuchokera kumalo otere kuyesedwa, mfundo zowerengedwa zonse zidzakhala 0x00. Ngati pulogalamuyo ipitilira kapena kutha kwa pulogalamuyo kukhazikitsidwa m'malo osankhidwa kuti atetezedwe kung'anima pakuwongolera, chipika chonse chomwe chimaphatikizapo gawolo chikhoza kukhazikitsidwa kukhala 0x00. Makamaka, ngati malo a ID (OSIS) amatetezedwa ndi chitetezo chowerengera, kupanga mapulogalamu kapena kukhazikitsa pulogalamu yopumira kumapangitsa kuti malo a ID (OSIS) akhazikitsidwe ku 0x00 ndikuwongolera chipangizocho kukhala chosatheka.
    7. Zoyenera kugwiritsa ntchito mapulogalamu amasweka mu flash memory
       Pamene MCU amakwaniritsa zinthu zotsatirazi, pulogalamu yopuma ntchito kwa kung'anima kukumbukira ndikoyambitsidwa.
       • Code flash memory ya MCU ili mu kuwerenga.
       • Mafupipafupi a wotchi yadongosolo (ICLK) ya MCU ndi 1 MHz kapena kupitilira apo.
       • MCU ili mumayendedwe othamanga kwambiri kapena othamanga kwambiri.
       • Kwa [Kusweka] pa [Zikhazikiko Zachida Chothandizira], [Inde] yasankhidwira [Gwiritsani Ntchito Zowonongeka Za Flash].
         Zindikirani: Kwa [Koloko] patsamba la [Zikhazikiko Zolumikizira] la chosinthira emulator, [Inde] ikasankhidwa [Inde] yasankhidwira [Chilolezo cha Wotchi yosintha polemba pa-chip Flash Memory], zinthu (b) ndi (c) zitha kuchotsedwa.
         Ngati ntchito yopuma ya pulogalamuyo ikugwiritsidwa ntchito ndi chikhalidwe chilichonse chosakhutitsidwa, emulator ikuwonetsa uthenga wolakwika. Zikatero, gwiritsani ntchito chopumira cha Hardware kapena tsimikizirani kuti zinthu (a) mpaka (d) pamwambapa zakhutitsidwa.
    8. Flash memory I/O register
       Pambuyo pa ntchito yowonongeka yomwe imaphatikizapo kukonzanso kukumbukira kwa flash, mtengo wa flash memory I / O registry imalembedwanso ndi emulator debugger.

Zindikirani pa Kugwiritsa Ntchito Zowonongeka Zapulogalamu mu On-Chip SRAM

1. Kulembanso kwa ma breakpoints a mapulogalamu ndi mapulogalamu a ogwiritsa ntchito
   Ngati pulogalamu yosokoneza pulogalamu yalembedwa ndi pulogalamu ya ogwiritsa ntchito, pulogalamuyo siyiyimitsa ngakhale itadutsa pa adilesi. Zikatero, khazikitsani pulogalamuyo pambuyo poti chandamale pa-chip SRAM italembedwanso ndi pulogalamuyi.

Zolemba pa Kugwiritsa Ntchito Mapulogalamu Ophwanya Mapulogalamu (Zofala ku On-Chip SRAM ndi Flash Memory)

1. Kuwerenga adilesi yomwe pulogalamu yosokoneza yakhazikitsidwa
   Osawerenga adilesi yomwe pulogalamu ya ogwiritsa ntchito yakhazikitsa pulogalamu yosokoneza. Kuchita zimenezi kungachititse kuti pulogalamuyo igwire ntchito m’njira yosiyana ndi mmene imakhalira nthawi zonse.
2. Viewkukumbukira mu [Memory] view
   Mukamagwiritsa ntchito pulogalamu ya ogwiritsa ntchito, ngati zokumbukira zingapo zomwe zidakhazikitsidwa zikuwonetsedwa mu [Memory] view wa emulator debugger, mtengo (code ebreak malangizo) zomwe zikuwonetsedwa ndizosiyana ndi zomwe zili mu data yeniyeni ya pulogalamu.
3. Kuchotsa mapulogalamu breakpoints pamene emulator debugger ayenera kuchotsedwa
   Pamene emulator debugger iyenera kuchotsedwa, chotsani mapulaneti onse a mapulogalamu omwe akhazikitsidwa.
   Panthawiyi, yambitsaninso CPU popeza wochotsa emulator amatsimikiza kukonzanso kukumbukira kwa flash.

Zindikirani pa Zolemba za Peripheral I/O Zosungidwa ndi Wochotsa Debugger

1. Zolembera za I/O zokhala ndi wochotsa
   The emulator debugger occupies zotsatirazi zotumphukira I/O kaundula pa debugging. Osasintha zikhalidwe zamakaundulawa, popeza kupitiliza kusokoneza sikungatheke mutatero.
   • Debug stop control registry (DBGSTOPCR)
   • Registry control OCD control Registry (SYOCDCR)

Zolemba pa Low-Power Modes

1. Kuthetsa vuto pamapulogalamu oyimirira kapena kutsitsimula
   Mu pulogalamu standby kapena mode snooze, emulator debugger alibe mwayi basi dongosolo la MCU. Pomwe pulogalamu ya ogwiritsa ntchito ikuchitidwa kapena pakusintha kwa MCU, kukhazikitsa ndi viewkukumbukira kapena zolembera za I/O zozungulira ndikukhazikitsa ndikusintha malo opumira sikutheka.
2. Kuyimitsa pulogalamu mokakamiza pamapulogalamu oyimirira kapena kutsitsimula
   Pulogalamu ikayimitsidwa mokakamiza pakuyimilira kwa pulogalamu kapena kutsitsimula, pitilizani kuchita izi. Opaleshoniyi imatsogolera kumasulidwa ku pulogalamu yoyimilira kapena kuyimilira.
   • Kugwiritsa [Kuyimitsa ] wa emulator debugger kuyimitsa MCU pa malangizo lotsatira pambuyo malangizo WFI zimene zinachititsa kuti mode kusintha. Pamene [Imitsani ] iyenera kugwiritsidwa ntchito, pa [Kulumikizana] pa tsamba la [Zokonda Kulumikizana] patsamba lachosinthira emulator, sankhani [Inde] pa [Kugwiritsa Ntchito Mphamvu Zochepa].

Zojambulidwa Zamakono panthawi ya Debugging
Popeza madera debugging mkati MCU nthawi zonse yogwira pa kugwirizana kwa emulator debugger, ndi MCU imakoka panopa kuposa dongosolo weniweni wosuta. Samalani pa mfundo iyi poyesa kuyeza zomwe zajambulidwa mu makina ogwiritsira ntchito.

Ma MCU omwe amagwiritsidwa ntchito pochotsa zolakwika
Pambuyo debugging ndi emulator, ngati MCU si olumikizidwa kwa emulator ndi kuthamanga paokha, ntchito zolondola sizingatsimikizike. Kuti mugwiritse ntchito MCU palokha, gwiritsani ntchito pulogalamu yokonza mapulogalamu kuti mukonzenso MCU.
MCUs olumikizidwa kwa emulator ndi ntchito debugging amaikidwa pansi pa nkhawa ndi mobwerezabwereza mapulogalamu kukumbukira kung'anima pa kutsanzira. Osagwiritsa ntchito ma MCU omwe adagwiritsidwa ntchito pochotsa zolakwika pakuchulukitsa kwa ogwiritsa ntchito.

Kuwunika Komaliza kwa Pulogalamu Yogwiritsa Ntchito
Musanalowe mu gawo la kupanga misa, onetsetsani kuti mukuwunika komaliza pulogalamu yomwe yalembedwa ku ROM yowunikira ndi pulogalamu yamapulogalamu, popanda emulator yolumikizidwa.

Mbiri Yobwereza

E2 Emulator, E2 Emulator Lite
Chikalata chowonjezera cha Buku Logwiritsa Ntchito
(Zolemba pa Kulumikizana kwa RISC-V MCU Devices)

Rev.	Tsiku	Kufotokozera
		Tsamba	Chidule
1.00	Marichi.25.2024	¾	Kope Loyamba latulutsidwa.

E2 Emulator, E2 Emulator Lite
Chikalata chowonjezera cha Buku Logwiritsa Ntchito
(Zolemba pa Kulumikizana kwa RISC-V MCU Devices)
Tsiku Lofalitsidwa: Rev.1.00 Mar.25.2024
Lofalitsidwa ndi: Renesas Electronics Corporation

Zolemba / Zothandizira

RENESAS E2 Emulator Chip Debugging Emulator [pdf] Buku Logwiritsa Ntchito E2 Emulator Chip Debugging Emulator, E2 Emulator, Chip Debugging Emulator, Debugging Emulator, Emulator

Maumboni

• Buku Logwiritsa Ntchito