EPEVER VS6048AU 60A Solar Charger Controller User Manual

1. Overview

Bedankt voor het selecteren van de ViewStar AU series common positive solar charge controller. The VS-AU controller is a PWM charge controller with built-in LCD display that adopts the most advanced digital technique. The multiple load control modes enable it to be widely used in solar home systems, traffic signals, solar street lights, solar garden lamps, enz.

Raadpleeg voor een uitgebreide handleiding de officiële gebruikershandleiding in PDF-formaat: EPEVER VS-AU Series User Manual (PDF)

2. Producteigenschappen

• Adopt high quality components of ST, IR and Infineon, ensuring product lifespan.
• Terminals have UL and VDE certification, making the product safer and more reliable.
• Controller can work continuously at full load within the environment temperature range from -25°C to 55°C.
• 3-Stage intelligent PWM-opladen: Bulk, Boost/Equalize, Float.
• Ondersteuning van 3 oplaadopties: Sealed, Gel en Flooded.
• LCD display design, dynamically displaying device's operating data and working condition.
• Double USB design, providing power supply charge for electronic equipment (5VDC/2.4A total).
• Gebruiksvriendelijke knopinstellingen voor comfortabele en gemakkelijke bediening.
• Meerdere modi voor lastregeling.
• Energiestatistiekfunctie.
• Accutemperatuurcompensatiefunctie.
• Uitgebreide elektronische bescherming.

Image: Detailed features and technical specifications of the VS-AU series solar charge controller.

3. Setup (Wiring)

Connect components to the charge controller in the sequence shown in the diagram below, paying close attention to the "+" and "-" terminals. Do not insert the fuse or turn on the breaker during installation. When disconnecting the system, the order will be reversed.

NOTE: Always connect the battery first to allow the controller to recognize the system voltage. The battery fuse should be installed as close to the battery as possible, with a suggested distance within 150mm.

NOTE: The VS-AU series is a positive ground controller. Any positive connection of solar, load or battery can be earth grounded as required.

NOTE: Please connect the inverter or other load that has a large start current to the battery rather than to the controller, if the inverter or other load is necessary.

Image: Connection Diagram for Solar Charger Controller

Afbeelding: Example Installation Setups

4. Bediening

Image: Solar Charger Controller with Labeled Components

4.1 Knop Functie

4.2 LCD-scherm

The LCD dynamically displays the device's operating data and working conditions. Below is a description of the icons and their status:

NOTE: When no operation, the interface will automatically cycle, but the follow two interfaces will not be displayed: Load Type and Battery Type.

NOTE: Accumulative power zero clearing: Under PV power interface, press SET button and hold for 5 seconds until the value blinks, then press SET button again to clear the value.

NOTE: Setting temperature unit: Under battery temperature interface, press SET button and hold for 5 seconds to switch.

4.3 Load Mode Setting

To set the load mode: Under the load mode setting interface, press the SET button and hold for 5 seconds until the number starts flashing. Then press the MENU button to set the parameter, and press the SET button to confirm.

NOTE: Please set Light ON/OFF, Test mode and Manual mode via Timer1. Timer2 will be disabled and display "2 n".

4.4 Batterijtype

To set the battery type: Under the Battery Voltage interface, press the SET button and hold for 5 seconds to enter the battery type setting interface. After choosing the battery type by pressing the MENU button, wait for 5 seconds or press the SET button again to modify successfully.

OPMERKING: Raadpleeg de batterij voltage parameters table in the Technical Specifications section for different battery types.

5. Bescherming

6. Probleemoplossing

7. Technische specificaties

※Parameters are for 12V system at 25°C; values are doubled for 24V system, tripled for 36V system, and quadrupled for 48V system.

8. Warranty and Support (Disclaimer)

Deze garantie is niet van toepassing onder de volgende voorwaarden:

1. Schade door oneigenlijk gebruik of gebruik in een ongeschikte omgeving.
2. PV of laadstroom, voltage of vermogen dat de nominale waarde van de controller overschrijdt.
3. The controller's working temperature exceeds the limit working environment temperature.
4. Gebruiker demontage of poging tot reparatie van de controller zonder toestemming.
5. De controller is beschadigd door natuurelementen, bijvoorbeeld bliksem.
6. De controller is beschadigd tijdens transport en verzending.

9. Gebruikerstips

No specific user tips or common issues were provided in the available data. Always ensure proper wiring sequence (battery first) and verify system voltage-instellingen voor optimale prestaties.