INSTALLATION GUIDE
MODEL: V5-NTG46-PNP
Compatible with Mercedes Benz vehicles with COMAND Online NTG4.5 navigation and Audio20 NTG45 system with 4pin HSD LVDS connector
Product features
- Interactive lane lines
- Own on-screen display and setup
- 2 trigger outputs (+12V max. 1A), separately adjustable switching events (CAN, ACC, rear-view camera, reverse gear)
- Rear-view camera input
- Front camera input
- Automatic switching to rear-view camera input on engagement of reverse gear from all operation modes
- Manual switching to rear-view camera
- Manual return from rear-view and front camera (cancellation of automatic switching)
- Compatible with all factory video accessories (e.g. rear-view camera, DVD-changer, TV-tuner)
- USB update-port for software-updates by consumer
- Plug&Play installation
Legal Information
By law, watching moving pictures while driving is prohibited, the driver must not be distracted. We do not accept any liability for material damage or personal injury resulting, directly or indirectly, from installation or operation of this product. This product should only be used while standing or to display fixed menus or rear-view-camera video when the vehicle is moving, for example the MP3 menu for DVD upgrades.
Changes/updates of the vehicle’s software can cause malfunctions of the interface. We offer free software-updates for our interfaces for one year after purchase. To receive a free update, the interface must be sent in at own cost. Labor cost for and other expenses involved with the software-updates will not be refunded.
1. Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources.
1.1. Delivery contents
1.2. Check compatibility of vehicle and accessories
Requirements
- Vehicle: Mercedes Benz with 6”/ 7“ monitor and 4pin HSD LVDS connector
- Device: COMAND Online NTG4.5, Audio20 NTG4.5
1.3. Setting the DIP switches of the interface-box V5C-M613
DIP 1 on the back of the interface-box V5C-M613 is used to set the monitor type.
| Device | DIP 1 | DIP 2 | DIP 3 |
| COMAND Online NTG4.5 | ON | OFF | OFF |
| Audio20 NTG4.5 – Version 1 | OFF | OFF | OFF |
| Audio20 NTG4.5 – Version 2 | OFF | ON | OFF |
After each change of the DIP switch settings you have to execute a power reset of the interface interface-box!
1.4. LED‘s of the interface-box V5C-M613
2. Connection schema
3. Installation
Switch off ignition and disconnect the vehicle’s battery! The interface needs a permanent 12V source. If according to factory rules disconnecting the battery is to be avoided, it is usually sufficient to put the vehicle is sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a resistor lead.
If power source is not taken directly from the battery, the connection has to be checked for being start-up proven and permanent.
Prior to wire and device installation we suggest to connect and test correct function of all after-market and factory infotainment equipment!
The interface is installed on the backside of the head unit.
3.1. Connecting interface-box and harnesses
- Remove the female Quadlock connector of the vehicle harness from the rear of the navigation computer.
- Remove optical leads from the female Quadlock connector of the vehicle harness and insert them into the female Quadlock connector of harness TV-NTG2 at the same position.
- Remove the 12pin Quadlock plug inserts from the female Quadlock connector of the vehicle harness and insert them into the female Quadlock connector of harness TV-NTG2 at the same position
- Connect female Quadlock connector of vehicle harness to the male Quadlock connector of harness TV-NTG2.
- Connect female Quadlock connector of harness TV-NTG2 to the male Quadlock connector of the navigation computer.
- Connect female 8 pin molex connector of the harness TV-NTG2 to the male 8 pin molex connector of the harness V5C-UNI01.
- Connect female 12pin AMP connector of the harness V5C-UNI01 to the front site of the V5C-M613 interface box.
3.2. LVDS connection
- Connect the female 4pin HSD LVDS connector of the LVDS cable CAB-HSD-DD075-O to the male 4pin HSD LVDS connector (LVDS-IN) on the rear of the interface-box V5C-M613.
- Remove the grey female 4pin HSD LVDS connector of the vehicle harness at the back of the head unit and connect it to the male 4pin HSD LVDS of the CAB-HSD-MG060-OZ LVDS cable.
- Connect the female 4pin HSD LVDS connector of the LVDS cable CAB-HSD-MG060-OZ to the male 4pin HSD LVDS connector (LVDS-OUT) on the rear of the interface-box V5C-M613.
- Connect the female 4pin HSD LVDS connector of the LVDS cable CAB-HSD-DD075-O to the grey male 4pin HSD LVDS connector on the rear of the head unit.
3.2.1. After-market front camera
3.2.1.1. Connection to the after-market front camera
1. Connect the video RCA of the after-market front camera to the female RCA connector “FRONT CAM” of the interface box V5C-M613.
2. The pink wire of harness V5C-UNI01 can be used for +12V electric power supply (max. 1A) of the after-market front camera. Configure in the OSDmenu “OPTION”, menu item “POWER OUT 2” the designated electric power supply (see chapter “Configurable switching outputs”).
3.2.1.2. Settings for connecting an after-market front camera
You have to configure some settings in the OSD-menus INPUTS and MISC if you want to connect an after-market front camera (Operation of the OSD: see chapter “OSD-Operation”).
Note: You can deactivate the enabled parking process by pressing the “right arrow” button on steering wheel. After deactivation you can’t enable the parking process again until the vehicle is diving faster than 30km/h or the ignition is switched off.
3.2.2. Rear-view camera
3.2.2.1. Connection to the after-market rear-view camera
- Connect the video RCA of the after-market rear-view camera to the female RCA connector “REAR CAM” of the interface box V5C-M613.
- The green wire of harness TV-NTG2 can be used for +12V electric power supply (max. 1A) of the aftermarket rear-view camera. Configure in the OSDmenu “OPTION”, menu item “POWER OUT 2” the designated electric power supply (see chapter “Configurable switching outputs”).
3.2.2.2. Settings for connecting an after-market rear-view camera
You have to configure some settings in the OSD-menus INPUT and OPTION if you want to connect an after-market rear-view camera (Operation of the OSD: see chapter “OSDOperation”).
Note: You can deactivate the enabled parking process by pressing the “right arrow” button on steering wheel. After deactivation you can’t enable the parking process again until the vehicle is diving faster than 30km/h or the ignition is switched off.
3.2.2.3. Settings for OEM rear-view camera
| OSD-menu | Menu item | Setting | Explication |
| INPUT | RVC | OEM | If a factory rear-view camera is existing! The interface turns off, if reverse gear isenabled and it displays factory rear-view camera |
| OPTION | PARK LOGIC | Rgear Only | Enabled while parking process |
3.2.3. Configurable trigger outputs
1. You can configure the both +12V trigger outputs separately. The pink wire is POWER OUT 1 and the green wire is POWER OUT 2.
Note: You can configure the both trigger outputs in the OSD-menu OPTION separately (Operation of the OSD: see chapter “OSD-Operation”).
3.3. Interactive lane lines
You have to configure some settings in the OSD-menu OPTION if you want to activate interactive lane lines (Operation of the OSD: see chapter “OSD-Operation”).
3.4. Picture settings
You can change the picture settings in the OSD-menu IMAGE (activation only from interface video level possible).
- Brightness
- Contrast
- Saturation
- Hue
- Sharpness
Note: The picture settings will be retained for each video-source separately.
4. Operation
4.1. OSD – On-screen display
You can change the basic configurations of the interface in the OSD (on screen display).
4.1.1. OSD – Operation
You can control the OSD by steering wheel buttons. Set the “radio level” in instrument cluster before you start the OSD control.
4.1.2. OSD – Additional setting options
The following settings in the OSD-menus OPTION and OSD can be configured over and above the described settings in this manual (Operation of the OSD: see chapter “OSD-Operation”):
4.2. Selecting the interface as current AV-source
Long press “left arrow” button to choose the interface as current video source.
Short press ”hang-up” button switch the video sources (cameras). Each short press will switch to the next enabled input. If all inputs are enabled the order is:
FRONT CAM à REAR CAM à …
Inputs which are not enabled are skipped.
5. Specifications
- Operation voltage 10.5 – 14.8V DC
- Stand-by power drain <0,1mA
- Operation power drain 190mA
- Power consumption 2,6W
- Temperature range -20°C to +80°C
- Weight (box only) 285g
- Measurements (box only) B x H x T 141 x 30 x 105 mm
6. Connections (interface-box)
7. Technical Support
CAS GmbH
manufacturer/distribution
In den Fuchslöchern 3
D-67240 Bobenheim-Roxheim
email support@casgermany.com
Legal disclaimer: Mentioned company and trademarks, as well as product names/codes are registered
trademarks ® of their corresponding legal owners.
FAQ
Q: Can I use this product while driving?
A: By law, watching moving pictures while driving is prohibited.
This product should only be used when standing still or displaying fixed menus or rear-view-camera video.
Q: How do I update the software of the interface?
A: We offer free software updates for one year after purchase.
To receive an update, you need to send in the interface at your own cost.
Documents / Resources
 |
NavLinkz V5-NTG46-PNP v.Logic Intelligent Solution Interface [pdf] Installation Guide V5-NTG46-PNP, V5-NTG46-PNP v.Logic Intelligent Solution Interface, V5-NTG46-PNP, v.Logic Intelligent Solution Interface, Intelligent Solution Interface, Solution Interface, Interface |
