FTI-CDP1 Vehicle Coverage and Preparation Notes

“

Product Specifications:

• Make: DL-CH8 RAM
• Model: 2500 TIP Start (Gas)
• Year: 2018
• Install Type: Type 2
• CAN: CJB

Product Usage Instructions:

Installation:

Before installing, confirm application, flash module, and update
the controller firmware with BLADE-AL(DL)-CH8 firmware for covered
vehicles.

Type 2 vehicles should use the included CAN extension cable to
source CAN data from either the green CAN junction block or from
the BCM.

Lighting:

Type B parking lights use the 10-pin connector. Secure any
unused 6-pin connector for safety.

Ignition:

Common ignition provisions are listed in the BLADE diagram.
Ignition can also be sourced from the vehicle BCM.

FAQ:

LED Programming Error Codes:

• 1x: CAN Error, check CAN wiring and
  voltages
• 2x: Key code not learned, confirm unlock sent,
  check CAN
• 3x: No immobilizer data, check immo data
  connection
• 4x: No IGN, check IGN connection
• 5x: VIN not found, check CAN connections
• 6x: No immobilizer data, check immo data
  connection
• 7x: Not the same key, use only one key for
  programming
• 8x: No immobilizer data, check immo data
  connection
• 9x: No immobilizer data
• 10x: Klon error, redo Klon

Module Programming Procedure – With Klon:

1. Close driver door.
2. Turn key to OFF position.
3. Re-open driver door to wake up data bus.
4. Press UNLOCK on OEM remote. If no OEM remote, press module
   programming button.
5. Wait for LED to flash BLUE once [1x].
6. Turn key to ON position.
7. Wait for LED to turn solid RED.
8. Turn key to OFF position.
9. Remove key.
10. Insert key into ignition and turn to ON position.
11. Wait for LED to flash BLUE again.
12. WARNING: Disconnect power last. Disconnect RS
    from the vehicle.

“`

FTI-CDP1 – Vehicle Coverage and Preparation Notes

Make
DL-CH8 RAM

Model 2500 TIP Start (Gas)

Year 2018

Install Type 2

CAN CJB

Lights
Park / Auto
Type B

IGN BCM

Hood I/O Changes

BCM

Green White/Blue

Firmware: Covered vehicles use either BLADE-AL(DL)-CH8, confirm application, flash module, and update the controller firmware before installing.
Install: Type 2 vehicles use the included CAN extension cable to source CAN data from the green CAN junction block (left side of the dash) or from the BCM (pin#25, CANH, brown, pin #26, CANL, yellow).
Lighting: Type B parking lights use the 10-pin connector, secure unused 6-pin connector for safety.
Ignition: Common ignition provisions are listed in the BLADE diagram, ignition is also available at the vehicle BCM (connector C5/E, pin #27, pink/white).

FTI-CDP1 – Installation and Configuration Notes A Required CAN connections. B Not required. C Hood pin connection (if required). D Ignition jumper, NO CONNECTION required. E Ignition connection.

IIIIIIIIIIIIIIIIIIIIIIEIIIRIIIIIIIIIIIIIIIIIIIIIIIIIIIII

D LAN

2001

O

O

Z

K E R E D
st. E

IIIIIIIII

S

ID

D
KO O
rG

fo AD E
R R

E ‘T T AN NC

CE AND

WHO

O H W
WANNA

LEARN

TO

IIIIIIIII

BLADE FEATURE COVERAGE

CM7000/7200 Cut loop for A/T
CM7X00
CM-900S/900AS
CM900AS/900S Jumper

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII D
O OTHER STUFF GOOD TOO
IMMOBILIZER DATA PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM DOOR STATUS RAP SHUTDOWN BRAKE STATUS E-BRAKE STATUS TACH OUTPUT GLOW PLUG STATUS SECURE TAKEOVER PARKING LIGHTS
CM -900

FTI-CDP1 – DL-CH8 – Type 2 2018 RAM 2500 TIP Start (Gas)

BLADE

PWR

pink/black

HOOD

D
C

green pink
A

B
B

3 4 1

Firstech Techfeedtree
2

OBD-II connector 1
1
16

TIP Start Cylinder

ACC RUN S

2

TART

OF F

Type B

Headlight switch
3
AUTO

*Not required

BCM 4

RAP SHUTDOWN

5
Green Junction Block

HL

C5 – Ignition

Driver side dash

A

or

48

39 27 26 25

brown

10

1

E

yellow

pink/white

C
INSTALL AFTERMARKET PART IF REQUIRED

LED Programming Error Codes
Module LED flashing RED during programming
1x – CAN Error, check CAN wiring and voltages 2x – Key code not learned, confirm unlock sent, check CAN 3x – No immobilizer data, check immo data connection 4x – No IGN, check IGN connection 5x – VIN not found, check CAN connections 6x – No immobilizer data, check immo data connection 7x – Not the same key, use only one key for programming 8x – No immobilizer data, check immo data connection 9x – No immobilizer data 10x – Klon error, redo Klon

INSTALL GUIDE

Patent No. US 8,856,780 CA 2759622

ALL IN ONE
DODGE/RAM

COM-BLADE-AL(DL)-CH8-EN

Doc. No.: ##65995## 20191004

MODULE PROGRAMMING PROCEDURE – WITH KLON

1

Close driver door.

11

OFF

Turn key to OFF position.

2
3 4 5 6 7 8 9 10

Re-open driver door to wake up data bus.
Press UNLOCK on OEM remote. If the vehicle is not equipped with an OEM remote, press the module programming button.
Wait, LED will flash BLUE once [1x].
Turn key to ON position.
ON
Wait, LED will turn solid RED.

OFF

Turn key to OFF position.

Remove key.

Insert key into ignition.

Turn key to ON position. ON
Wait, LED will flash BLUE.

12 13

WARNING: Disconnect power last. Disconnect RS from vehicle.
Connect RS to computer and proceed with extended programming.

14

WARNING: Do not press RS programming button. Connect power first. Connect RS to vehicle.

15 16 17

Turn key to ON position.
ON
Wait, LED will turn solid BLUE for 2 seconds.

OFF

Turn key to OFF position.

18 19

START

Turn key to START position.

OFF

Turn key to OFF position.

20

Module Programming Procedure completed.

WWW.IDATALINK.COM

Automotive Data Solutions Inc. © 2020

INSTALL GUIDE

Patent No. US 8,856,780 CA 2759622

ALL IN ONE
DODGE/RAM

COM-BLADE-AL(DL)-CH8-EN

Doc. No.: ##65995## 20191004

WARNING: READ BEFORE RNEOMTOICTEE STARTING THE VEHICLE

IMPORTANT
I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction.

TAKE OVER PROCEDURE – TO THE VEHICLE OWNER

NOTE

2

I All vehicle doors must be closed and locked prior to remote start sequence.

TIME RESTRICTI N COMING UP !

1

Press UNLOCK on after-market

remote.

3

TIME RESTRICTI N
Within 45 SECONDSfrom previous step:
Open vehicle door. Enter vehicle. Close vehicle door. Insert key into ignition. Turn key to ON position. Press and release BRAKE pedal.
Take over procedure completed.

!

Failure to follow procedure within time restriction will result in vehicle engine shutdown.

WWW.IDATALINK.COM

Automotive Data Solutions Inc. © 2020

Documents / Resources

	myFirstech FTI-CDP1 Vehicle Coverage and Preparation Notes [pdf] Installation Guide DL-CH8 RAM 2500 Tip Start Gas_18, FTI-CDP1 Vehicle Coverage and Preparation Notes, FTI-CDP1, Vehicle Coverage and Preparation Notes, Coverage and Preparation Notes, Preparation Notes, Notes
	myFirstech FTI-CDP1 Vehicle Coverage and Preparation Notes [pdf] Installation Guide DL-CH7, CM7000-7200, CM-900S-900AS, CM-900, FTI-CDP1 Vehicle Coverage and Preparation Notes, FTI-CDP1, Vehicle Coverage and Preparation Notes, Coverage and Preparation Notes, Preparation Notes, Notes
	myFirstech FTI-CDP1 Vehicle Coverage and Preparation Notes [pdf] Installation Guide DL-CH7, CM7000-7200, CM-900S-900AS, CM-900, FTI-CDP1 Vehicle Coverage and Preparation Notes, FTI-CDP1, Vehicle Coverage and Preparation Notes, Coverage and Preparation Notes, Preparation Notes, Notes
	myFirstech FTI-CDP1 Vehicle Coverage and Preparation Notes [pdf] Installation Guide DL-CH7, CM7000-7200, CM-900S-900AS, CM-900, FTI-CDP1 Vehicle Coverage and Preparation Notes, FTI-CDP1, Vehicle Coverage and Preparation Notes, Coverage and Preparation Notes, Preparation Notes, Notes
	myFirstech FTI-CDP1 Vehicle Coverage and Preparation Notes [pdf] Installation Guide DL-CH7, CM7000-7200, CM-900S-900AS, CM-900, FTI-CDP1 Vehicle Coverage and Preparation Notes, FTI-CDP1, Vehicle Coverage and Preparation Notes, Coverage and Preparation Notes, Preparation Notes, Notes
	myFirstech FTI-CDP1 Vehicle Coverage and Preparation Notes [pdf] Installation Guide DL-CH7 RAM 1500 PTS, FTI-CDP1 Vehicle Coverage and Preparation Notes, FTI-CDP1, Vehicle Coverage and Preparation Notes, Coverage and Preparation Notes, Preparation Notes, Notes
	myFirstech FTI-CDP1 Vehicle Coverage and Preparation Notes [pdf] Installation Guide DL-CH7 RAM 2500 PTS 18, FTI-CDP1 Vehicle Coverage and Preparation Notes, FTI-CDP1, Vehicle Coverage and Preparation Notes, Coverage and Preparation Notes, Preparation Notes, Notes
	myFirstech FTI-CDP1 Vehicle Coverage and Preparation Notes [pdf] Installation Guide DL-CH7 RAM 3500 PTS, FTI-CDP1 Vehicle Coverage and Preparation Notes, FTI-CDP1, Vehicle Coverage and Preparation Notes, Coverage and Preparation Notes, Preparation Notes, Notes
	myFirstech FTI-CDP1 Vehicle Coverage and Preparation Notes [pdf] Installation Guide FTI-CDP1 Vehicle Coverage and Preparation Notes, FTI-CDP1, Vehicle Coverage and Preparation Notes, Coverage and Preparation Notes, Preparation Notes, Notes
	myFirstech FTI-CDP1 Vehicle Coverage and Preparation Notes [pdf] Installation Guide DL-CH7 RAM 3500 PTS Diesel 18, FTI-CDP1 Vehicle Coverage and Preparation Notes, FTI-CDP1, Vehicle Coverage and Preparation Notes, Coverage and Preparation Notes, Preparation Notes, Notes

References

• User Manual