iDatalink - Home
Installation Guide for myFirstech models including: FTI-CDP1 Vehicle Coverage and Preparation Notes, FTI-CDP1, Vehicle Coverage and Preparation Notes, Coverage and Preparation Notes, Preparation Notes, Notes
FTI-CDP1 | MyFirstech Install
File Info : application/pdf, 4 Pages, 500.10KB
DocumentDocumentFTI-CDP1: Vehicle Coverage and Preparation Notes Make DL-CH7 RAM Model 3500 PTS Diesel Year Install 2013-17 Type 1 CAN Lights OBD-II Park / Auto Type B IGN BCM Hood I/O Changes BCM Green White/Blue Firmware: Covered vehicles use BLADE-AL(DL)-CH7, confirm application, flash module, and update the controller firmware before installing. CAN: Type 1 vehicles use CAN connections in harness at OBD-II, the included CAN extension is not required for this install type. Lighting: Type B parking lights use the 10-pin connector, please ensure that the unused 6-pin connector is properly secured for safety. Ignition: Common ignition provisions are listed in the BLADE diagram, ignition is also available at the vehicle BCM (connector C5/E, pink/white, pin #27), FTI-CDP1 - Installation and Configuration Notes A Required CAN connections. B Not Required. C Hood pin connection (if required). D Ignition jumper, NO CONNECTION required. E Ignition connection. IIIIIIIIIIIIIIIIIIIIIIEIIIRIIIIIIIIIIIIIIIIIIIIIIIIIIIII D LAN 2001 O O Z K E R E D st. E IIIIIIIII S ID D KO O rG fo AD E R R E 'T T AN NC CE AND WHO O H W WANNA LEARN TO IIIIIIIII FEATURE COVERAGE CM7000/7200 Cut loop for A/T CM7X00 CM-900S/900AS CM900AS/900S Jumper IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII D O OTHER STUFF GOOD TOO IMMOBILIZER DATA PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM DOOR STATUS RAP SHUTDOWN BRAKE STATUS E-BRAKE STATUS TACH OUTPUT GLOW PLUG STATUS SECURE TAKEOVER PARKING LIGHTS CM -900 FTI-CDP1 - DL-CH7 - Type 1 2013-17 RAM 3500 PTS Diesel Diesel WTS BLADE PWR pink Set feature option 4-10-4 pink/black *Not required D B B HOOD green pink C A A 3 4 1 Firstech Techfeedtree 2 OBD-II connector 1 1 16 PTS button 2 ENGINE START STOP *Not required Type B Headlight switch 3 AUTO BCM 4 RAP SHUTDOWN C5 - Ignition 48 39 27 26 25 E 10 1 pink/white C INSTALL AFTERMARKET PART IF REQUIRED LED Programming Error Codes Module LED flashing RED during programming 1x - CAN Error, check CAN wiring and voltages 2x - Key code not learned, confirm unlock sent, check CAN 3x - No PTS signal, check button connection 4x - No immobilizer data, check wiring 4x - No immobilizer, confirm only one key in vehicle 5x - No ignition, check wiring 6x - VIN error, check CAN wiring, confirm vehicle application 7x - PTS signal error, check button connection 8x - No PTS signal, check button connection INSTALL GUIDE Patent No. US 8,856,780 CA 2759622 COM-BLADE-AL(DL)-CH7-EN CARTRIDGE INSTALLATION 1 Slide cartridge into unit. Notice button under LED. 2 ALL IN ONE CHRYSLER/DODGE/JEEP/RAM Doc. No.: ##72396## 20201117 Ready for Module Programming Procedure. MODULE PROGRAMMING PROCEDURE - WITH KLON - 1 OF 2 1 Close driver door. 7 Wait, LED will turn solid RED. Re-open driver door to wake up data bus. 8 Push start button once [1x] to x1 OFF position. 2 Press UNLOCK on keyfob 1. 9 Push start button twice [2x] with x2 keyfob 1 to ON position. (No battery) 3 x1 Wait, LED will flash BLUE once [1x]. 10 Wait, if LED flashes BLUE rapidly, proceed to step 11. If LED turns solid RED, repeat steps 8 to 10. 4 Remove valet key from keyfob 1. 11 Push start button once [1x] to x1 OFF position. 12 Disconnect all connectors from remote starter except the power connector. 5 Remove batteries from keyfob 1. 13 Disconnect the power connector. 6 Push start button twice [2x] with x2 keyfob 1 to ON position. (No battery) IMPORTANT: READ NEXT PAGE ! WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020 INSTALL GUIDE Patent No. US 8,856,780 CA 2759622 ALL IN ONE CHRYSLER/DODGE/JEEP/RAM MODULE PROGRAMMING PROCEDURE - WITH KLON - 2 OF 2 14 Remove remote starter from vehicle. 18 Close driver door. 15 Connect remote starter to computer. 19 Re-open driver door to wake up data bus. Push start button twice [2x] with x2 keyfob 1 to ON position. (No battery) 16 17 Proceed with extended programming. Connect remote starter to vehicle. 20 21 22 Wait, LED will turn solid BLUE for 2 seconds. Push start button once [1x] to x1 OFF position. Module Programming Procedure completed. Insert battery in keyfob 1. WARNING: READ BEFORE RNEOMTOICTEE STARTING THE VEHICLE IMPORTANT I All OEM keyfobs must be at least 10 feet away from the vehicle. All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction. TAKE OVER PROCEDURE - TO THE VEHICLE OWNER NOTE 2 I All vehicle doors must be closed and locked prior to remote start sequence. TIME RESTRICTI N COMING UP ! TIME RESTRICTI N Within 45 SECONDSfrom previous step: Open vehicle door. Enter vehicle. Close vehicle door. Press and release BRAKE pedal. 1 Press UNLOCK on after-market remote. 3 Take over procedure completed. ! Failure to follow procedure within time restriction will result in vehicle engine shutdown. WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020