spec5 Nomad Radio Linux ARM ကွန်ပျူတာ

ကျေးဇူးတင်ပါသည်

Thank you for ordering your Spec Five Nomad from Spec Five. Here are the instructions to get you connected to your new device and join the mesh.

သတိပေးချက်- DO NOT POWER ON YOUR SPECFIVE NOMAD UNTIL YOU HAVE CONNECTED THE ANTENNAS.
POWERING THE SPECFIVE NOMAD WITHOUT THE ANTENNAS CONNECTED CAN CAUSE DAMAGE TO THE LORA BOARD.

Antenna ချိတ်ဆက်မှု

If removed for shipping or storage, Install the antennas according to the image below. The Long Antenna is the Lora Antenna and the short antenna is the GPS antenna.

Installing the antennas in the incorrect location will not damage the Lora Board but it will reduce the range and transmission strength of the radio.

အဆိုပါပစ္စည်းအားသွင်း

• Use a USB-C cable to charge the Nomad from a 5 volt power adapter.
• Below the Keyboard is a battery level indicator which will illuminate when the power switch(on the right side of the Nomad) is in the ON(up) position.
  

Starting The Nomad

1. Move the switch on the Right side of the Nomad to up/ON position.
   a. The Battery level indicator below the keyboard will illuminate
   b. The speaker will make a pop/crackle sound as it powers up
   c. The Screen will initially come on a show “no signal”, but as the Raspberry Pi boots the screen will get signal.
2. The Nomad is set from the factory to boot to the home screen without the need to Login. The factory username and password are as follows:

အသုံးပြုသူအမည်- spec5
စကားဝှက်- 123456

Nomad Home Screen

Using The Meshtastic Client

1. ကိုဖွင့်ပါ။ Web browser (Chromium).
   
2. Select the Meshtastic Client from the recently viewed web စာမျက်နှာများ။
   
3. If you get a privacy error in Chromium, click “Advanced” and then click “Proceed to raspberrypi”.
   
4. Connect to a new device in the web ဖောက်သည်
   
5. The IP address for connecting to the Lora Radio will auto-populate as “raspberrypi”, click Connect.
   
6. Now you are connected to the Lora Radio through the Meshtastic Web လိုင်း။
   From here you have all of the functionality of the Phone Apps: Send Messages, join/create channels, change Configuration Settings, change device name/call sign.
   
7. Important configuration settings to check:
   a. Config -> Radio Config -> LORA Set Region to US.
   b. Config -> Radio Config -> Device Set Role to Client.
   c. Config -> Radio Config -> Position Set GPS Mode to Enabled.

မင်းသွားလို့ကောင်းတယ်။

ကီးဘုတ်ချိတ်ဆက်မှု

The Keyboard connects to the Raspberrypi via Bluetooth. The keyboard turns on with the main power switch and comes pre connected to the Pi. If the keyboard is not working it likely is no longer connected over Bluetooth. To reconnect the keyboard:

1. Use a round, blunt object like a paperclip to press the Bluetooth Button on the keyboard. The Blue LED will blink when the Keyboard is in Bluetooth pairing mode.
   
2. On the Menu Bar click on the Bluetooth icon, and select add device.
3. In the Pop up window, a “Bluetooth Keyboard” should be found. Click Pair and wait for the pairing process to successfully complete.
   

ဖောက်သည်ပံ့ပိုးမှု

အခြားအရင်းအမြစ်များ-
ရေဒီယိုဖွဲ့စည်းမှုဆက်တင်များဆိုင်ရာ နောက်ထပ်အချက်အလက်များအတွက်၊ သွားရောက်ကြည့်ရှုပါ။ https://meshtastic.org/docs/configuration/
ကျွန်ုပ်တို့၏ထုတ်ကုန်များအကြောင်း နောက်ထပ်အချက်အလက်များအတွက် ဝင်ရောက်ကြည့်ရှုပါ။ specfive.com

© 2024၊ Spec Five LLC All Right Reserved specfive.com

စာရွက်စာတမ်းများ / အရင်းအမြစ်များ

spec5 Nomad Radio Linux ARM ကွန်ပျူတာ [pdf] အသုံးပြုသူလမ်းညွှန် Nomad Radio Linux ARM Computer, Radio Linux ARM Computer, Linux ARM Computer, ARM Computer

ကိုးကား

• အသုံးပြုသူလက်စွဲ