Kompjuter ARM Linux Nomad Radio spec5

Kompjuter ARM Linux Nomad Radio spec5

Grazzi

Thank you for ordering your Spec Five Nomad from Spec Five. Here are the instructions to get you connected to your new device and join the mesh.

TWISSIJA: DO NOT POWER ON YOUR SPECFIVE NOMAD UNTIL YOU HAVE CONNECTED THE ANTENNAS.
POWERING THE SPECFIVE NOMAD WITHOUT THE ANTENNAS CONNECTED CAN CAUSE DAMAGE TO THE LORA BOARD.

Konnessjoni tal-antenna

If removed for shipping or storage, Install the antennas according to the image below. The Long Antenna is the Lora Antenna and the short antenna is the GPS antenna.

Konnessjoni tal-antenna

Installing the antennas in the incorrect location will not damage the Lora Board but it will reduce the range and transmission strength of the radio.

Iċċarġjar tal-Apparat

  • Use a USB-C cable to charge the Nomad from a 5 volt power adapter.
  • Below the Keyboard is a battery level indicator which will illuminate when the power switch(on the right side of the Nomad) is in the ON(up) position.
    Iċċarġjar tal-Apparat

Starting The Nomad

  1. Move the switch on the Right side of the Nomad to up/ON position.
    a. The Battery level indicator below the keyboard will illuminate
    b. The speaker will make a pop/crackle sound as it powers up
    c. The Screen will initially come on a show “no signal”, but as the Raspberry Pi boots the screen will get signal.
  2. The Nomad is set from the factory to boot to the home screen without the need to Login. The factory username and password are as follows:

Isem tal-utent: spec5
Password: 123456

Starting The Nomad
Nomad Home Screen

Using The Meshtastic Client

  1. Iftaħ il- Web browser (Chromium).
    Using The Meshtastic Client
  2. Select the Meshtastic Client from the recently viewed web paġni.
    Using The Meshtastic Client
  3. If you get a privacy error in Chromium, click “Advanced” and then click “Proceed to raspberrypi”.
    Using The Meshtastic Client
  4. Connect to a new device in the web klijent.
    Using The Meshtastic Client
  5. The IP address for connecting to the Lora Radio will auto-populate as “raspberrypi”, click Connect.
    Using The Meshtastic Client
  6. Now you are connected to the Lora Radio through the Meshtastic Web Klijent.
    From here you have all of the functionality of the Phone Apps: Send Messages, join/create channels, change Configuration Settings, change device name/call sign.
    Using The Meshtastic Client
  7. Important configuration settings to check:
    a. Config -> Radio Config -> LORA Set Region to US.
    b. Config -> Radio Config -> Device Set Role to Client.
    c. Config -> Radio Config -> Position Set GPS Mode to Enabled.

Lest biex Tmur!

Konnessjoni tat-Tastiera

The Keyboard connects to the Raspberrypi via Bluetooth. The keyboard turns on with the main power switch and comes pre connected to the Pi. If the keyboard is not working it likely is no longer connected over Bluetooth. To reconnect the keyboard:

  1. Use a round, blunt object like a paperclip to press the Bluetooth Button on the keyboard. The Blue LED will blink when the Keyboard is in Bluetooth pairing mode.
    Konnessjoni tat-Tastiera
  2. On the Menu Bar click on the Bluetooth icon, and select add device.
  3. In the Pop up window, a “Bluetooth Keyboard” should be found. Click Pair and wait for the pairing process to successfully complete.
    Konnessjoni tat-Tastiera

Appoġġ għall-Klijent

Riżorsi Oħra:
Għal aktar informazzjoni dwar is-settings tal-konfigurazzjoni tar-radju, żur https://meshtastic.org/docs/configuration/
Għal aktar informazzjoni dwar il-prodotti tagħna, żur specfive.com

© 2024, Spec Five LLC Id-Drittijiet kollha Riżervati specfive.com

Logo

Dokumenti / Riżorsi

Kompjuter ARM Linux Nomad Radio spec5 [pdfGwida għall-Utent
Nomad Radio Linux ARM Computer, Radio Linux ARM Computer, Linux ARM Computer, ARM Computer

Referenzi

Ħalli kumment

L-indirizz elettroniku tiegħek mhux se jiġi ppubblikat. L-oqsma meħtieġa huma mmarkati *