Milesight LogoQUICK START GUIDE
Speed Dome and Al Pro Box Plus Network CameraMilesight AI Pro Box Speed Dome Network CameraIP VIDEO SURVEILLANCE

Quick Installation Steps

Speed Dome Network Camera
Step1: Check the wall or ceiling condition. Ensure that there is sufficient strength to avoid flaking. It should be able to bear the weight eight times larger than the camera’s;
Step2: Use the wall or ceiling hanging holder to mark the holes. Drill 4 holes on the wall or ceiling;

Milesight AI Pro Box Speed Dome Network Camera - NetworkStep3: Put the cables through the holder. Match the holder with the screw holes of the camera body and secure them;

Milesight AI Pro Box Speed Dome Network Camera - Network 1Step4: Make sure that the camera body has been correctly installed to and match the holder to the holes on the wall or ceiling, then tighten up the screws.

Milesight AI Pro Box Speed Dome Network Camera - holder

AI Pro Box Plus Network Camera
Step1: Fix the lens and the cable for Iris controlling to the Pro Box Plus, then tighten the screw;Milesight AI Pro Box Speed Dome Network Camera - holder 1

Step2: Connect the cables. Fix the camera on the accessory which has already been installed on the position where the camera is intended to be mounted (Milesight provides Protective Housing(A51) for installation).

Milesight AI Pro Box Speed Dome Network Camera - ConnectNote:
You can press ABF button on the back panel of camera to help focusing.

Hardware Overview

Speed Dome Network Camera

Milesight AI Pro Box Speed Dome Network Camera - Connect 1

AI Pro Box Plus Network Camera

Milesight AI Pro Box Speed Dome Network Camera - Connect 2

How to Connect to Alarm Interface

Milesight AI Pro Box Speed Dome Network Camera - Alarm

PIN1: Alarm Output NC/NO 24V DC 1A
PIN2: Alarm Output NC/NO 24V DC 1A
PIN3: Alarm Input NC/NO ≤ 12V
PIN4: Alarm Input NC/NO ≤ 12V

How to Connect the Water-proof Connector

Milesight AI Pro Box Speed Dome Network Camera - Water

Note:
Please tightly wrapped all cable-out interface with adhesive tape at last to prevent them from water.
Step1: Get the network cable through the screw nut, rubber ring and the screw bolt;
Step2: Insert the rubber ring into the screw bolt;
Step3: Connect the screw nut to the screw bolt;
Step4: Place the O-Ring on the network port connector;
Step5: Connect the RJ45 to the network port connector, tighten the screw bolt and the connector.

Assigning an IP Address by Using Smart Tools

Smart Tools is a software tool which can automatically detect multiple online Milesight network cameras in the LAN, set IP addresses, and manage firmware upgrades. It’s recommended to use when assigning IP addresses for multiple cameras.

Milesight AI Pro Box Speed Dome Network Camera - Tools

The steps to change the IP of cameras are as below:

  1. Start Smart Tools, click the IPC Tools page, then enter the device information, such as IP address, MAC address, Port number, Netmask, and Gateway, then all related Milesight network cameras in the same network that will be shown.
  2. Select a camera or multiple cameras according to the MAC addresses.
  3. Click “Activate” to set the password when using the cameras for the first time (Password must be 8 to 32 characters long, contain at least one number and one letter), and set three security questions (If you forget the password, you can reset the password by answering three security questions correctly).
  4. Type the user name and password you set, change the IP address or other network values, and then click “Modify” button.
  5. By double clicking the selected camera or the browser of interested camera, you can access the camera via web browser directly.
    More usage of Smart Tools, please refer to the “Smart Tools User Manual”.

Assigning an IP Address via Browser

If the network segment of the computer and that of the camera are different, please add some 192.168.5.xx(255.255.255.0) for your PC to get access to your cameras, more details can be found on “Milesight Network Camera Quick Start”.

Accessing from the Web Brower

The camera can be used with the most standard operating systems and browsers.
The recommended browsers are Internet Explorer, Firefox, Chrome, Safari. More information about the plugin installation, please refer to the troubleshooting:
Milesight-Troubleshooting-Plugin Installation on Windows-IPC
Milesight-Troubleshooting-Plugin Installation on MAC
Speed Dome/
AI Pro Box Plus
Thank you for choosing Milesight Product Milesight Technology

Milesight AI Pro Box Speed Dome Network Camera - Qr CodeUser Manual
http://www.milesight.com/DownloadFile/UserManual/IPC/Milesight_Network_Camera_User_Manual_en.pdfMilesight AI Pro Box Speed Dome Network Camera - Qr Code 1http://www.milesight.com/product/MS_SmartTools.asp

Milesight AI Pro Box Speed Dome Network Camera - Icon All Software &files can be downloaded from http://www.milesight.com/support/download.asp

Better Inside, More in Sight
Milesight Technology
www.milesight.com

Documents / Resources

Milesight AI Pro Box Speed Dome Network Camera [pdf] User Guide
AI Pro Box Speed Dome Network Camera, AI Pro, Box Speed Dome Network Camera, Dome Network Camera, Network Camera, Camera

References

Leave a comment

Your email address will not be published. Required fields are marked *