Milesight | 5G, AI, IoT and LoRaWAN®
User Guide for Milesight models including: AI Pro Box Speed Dome Network Camera, AI Pro, Box Speed Dome Network Camera, Dome Network Camera, Network Camera, Camera
16 июн. 2025 г. — More usage of Smart Tools, please refer to the “Smart Tools User Manual”. If ... The recommended browsers are Internet Explorer, Firefox, Chrome, Safari.
File Info : application/pdf, 6 Pages, 14.42MB
DocumentDocumentSpeed Dome and AI Pro Box Plus Network Camera User Manual Smart Tools All Software &files can be downloaded from http://www.milesight.com/support/download.asp IP VIDEO SURVEILLANCE Table of Content 1. Quick Installation Steps.............................................................................................. 2 2. Hardware Overview................................................................................. 5 3. How to Connect to Alarm Interface........................................................................... 6 4. How to Connect the Water-proof Connector.......................................................... 6 5. Assigning an IP Address by Using Smart Tools.................................................... 7 6. Assigning an IP Address via Browser........................................................................ 7 7. Accessing from the Web Brower................................................................................. 7 www.milesight.com 1. Quick Installation Steps Speed Dome Network Camera Step1: Check the wall or ceiling condition. Ensure that there is sufficient strength to avoid flaking. It should be able to bear the weight eight times larger than the camera's; Step2: Use the wall or ceiling hanging holder to mark the holes. Drill 4 holes on the wall or ceiling; Step4: Make sure that the camera body has been correctly installed to and match the holder to the holes on the wall or ceiling, then tighten up the screws. Step3: Put the cables through the holder. Match the holder with the screw holes of the camera body and secure them; AI Pro Box Plus Network Camera Step1: Fix the lens and the cable for Iris controlling to the Pro Box Plus, then tighten the screw; 12 2 www.milesight.com (ABF) (Non-ABF) www.milesight.com 3 13 Step2: Connect the cables. Fix the camera on the accessory which has already been installed on the position where the camera is intended to be mounted (Milesight provides Protective Housing(A51) for installation). 2. Hardware Overview Speed Dome Network Camera (Standard Version) (Wiper Version) Note: You can press ABF button on the back panel of camera to help focusing. 14 www.milesight.com Light Sensor Lens IR LEDs IR LEDs Light Sensor Wiper Lens Rain Gauge Smart Sensor ALARM 3/4 G IN3 G IN4 AUDIO IN G OUT G ALARM 2 A B G IN ALARM 1 A B G IN AC 24V Alarm I/O Alarm I/O RS485 Audio I/O Alarm In*2 Ethernet Port AI Pro Box Plus Network Camera (ABF) Alarm In Alarm Out RS485 Ethernet Port (PoE) Power LED Indicator (Non-ABF) Alarm In Alarm Out RS485 ABF Error LED Indicator Ethernet Port (PoE) Power LED Indicator Error LED Indicator Grounding Power Connector Audio In/Out Reset microSD/SDHC/SDXC Grounding Power Connector Audio In/Out Reset microSD/SDHC/SDXC www.milesight.com 51 3. How to Connect to Alarm Interface Digital output Digital input PIN1 General I/O Terminal Block PIN2 PIN3 PIN4 12V PIN1: Alarm Output NC/NO 24V DC 1A PIN2: Alarm Output NC/NO 24V DC 1A PIN3: Alarm Input NC/NO 12V PIN4: Alarm Input NC/NO 12V 4. How to Connect the Water-proof Connector Network Port Connector LAN Rubber ring Screw bolt Screw nut O-Ring Step1: Get the network cable through the screw nut, rubber ring and the screw bolt; Step2: Insert the rubber ring into the screw bolt; Step3: Connect the screw nut to the screw bolt; Step4: Place the O-Ring on the network port connector; Step5: Connect the RJ45 to the network port connector, tighten the screw bolt and the connector. Note: Please tightly wrapped all cable-out interface with adhesive tape at last to prevent them from water. 16 www.milesight.com 5. Assigning an IP Address by Using Smart Tools Smart Tools is a software tool which can automatically detect multiple online Milesight network cameras in the LAN, set IP addresses, and manage firmware upgrades. It's recommended to use when assigning IP addresses for multiple cameras. The steps to change the IP of cameras are as below: 1) Start Smart Tools, click the IPC Tools page, then enter the device information, such as IP address, MAC address, Port number, Netmask, and Gateway, then all related Milesight network cameras in the same network that will be shown. 2) Select a camera or multiple cameras according to the MAC addresses. 3) Click "Activate" to set the password when using the cameras for the first time (Password must be 8 to 32 characters long, contain at least one number and one letter), and set three security questions (If you forget the password, you can reset the password by answering three security questions correctly). 4) Type the user name and password you set, change the IP address or other network values, and then click "Modify" button. 5) By double clicking the selected camera or the browser of interested camera, you can access the camera via web browser directly. More usage of Smart Tools, please refer to the "Smart Tools User Manual". 6. Assigning an IP Address via Browser If the network segment of the computer and that of the camera are different, please add some 192.168.5.xx(255.255.255.0) for your PC to get access to your cameras, more details can be found on "Milesight Network Camera Quick Start". 7. Accessing from the Web Brower The camera can be used with the most standard operating systems and browsers. The recommended browsers are Internet Explorer, Firefox, Chrome, Safari. More information about the plugin installation, please refer to the troubleshooting: 5.Milesight-Troubleshooting-Plugin Installation on Windows-IPC 6.Milesight-Troubleshooting-Plugin Installation on MAC www.milesight.com 71 Speed Dome/ AI Pro Box Plus Thank you for choosing Milesight Product Milesight Technology 18 www.milesight.com