Mi . Light
Subordinate New Brand
Panel Remote Controller
Model No.: T1 / T2 / T3 / T4 &B1 / B2 / B3 / B4
0223-2
Features
This panel remote controller is designed by a delicate and fashionable tempered glass panel, And we adopt a high precision capacitive touch screen IC. Touch screen is very stable; 2.4GHz high RF wireless control with long-distance controlling, low power consumption, and high-speed transmitting rate. This product has T series and B series, and the difference is the method of power supplying. Both series have 4 kinds: T1/B1 4-zone dimmable panel remote controller; T2/B2 CCT 4-zone panel remote controller; T3/B3 4-zone RGB/RGBW panel remote controller; T4/B4 4-zone RGB+CCT panel remote controller. This product widely work on our smart LED Lighting, LED controller and smart panel controller, etc.
| Panel Remote Controller Name |
Compatible Remote Model |
Compatible Products |
| 4-Zone brightness dimming Panel Remote Controller | FUT091 | Brightness dimming series |
| 4-Zone CCT adjust panel remote controller | FUT091 | CCT adjust series |
| 4-Zone RGB/RGBW panel remote controller | FUT095/FUT096 | RGB / RGBW series |
| 4-Zone RGB+CCT panel remote controller | FUT092 | RGB / RGBW RGB+CCT series |
Parameters
B Series: Powered by 3V(2*AAA Battery)
| Working Voltage: 3V(2*AAA Battery) | Modulation Method: GFSK |
| Transmitting Power: 6dBm | Control Distance: 30m |
| Standby Power: 20uA | Working Temp.: -20-60℃ |
| Transmission Frequency: 2.4GHz | Size: 86*86*19mm |
T Series: Powered by AC90-110V or AC180-240V
| Working Voltage: AC90-110V or AC180-240V | Control Distance: 30m |
| Transmitting Power: 6dBm | Working Temp.: -20-60℃ |
| Transmission Frequency: 2.4GHz | Size: 86*86*31mm |
| Modulation Method: GFSK |
Installation/ Dismantlement
B series Installation/ Dismantlement
T series Installation/ Dismantlement
 |
Install the bottom case into the wall; Above are the standard bottom cases. |
 |
Fix the controller base on the bottom case with screw. |
 |
Clicks into the upper side of glass panel on the controller base, then press the lower side slightly to make it clicks into the controller base. |
 |
Plug into the below bayonet with a screwdriver, and upwarp screwdriver, then you can dismantle the controller. |
Function of keys
Remark: When touching the button, LED indicating lamp will flash once with different sound (Touch slider with no sound).
B1 & T1
4-Zone Panel Remote Contoller ( Brightness )
 |
Touch dimming slider to change the brightness from 1~100%. |
 |
Touch master ON, turn on all linked lights. Long press 5 seconds to turn ON the indicating sound. |
 |
When the light is ON, press “60S Delay OFF”, the light will be OFF Automatically after 60 seconds. |
 |
Touch master OFF, turn off all linked lights. Long press 5 seconds to turn OFF the indicating sound. |
 |
Touch Zone ON, turn on zone-linked lights. |
 |
Touch Zone OFF, turn off zone-linked lights. |
B2 & T2
4-Zone Panel Remote Contoller ( Color Temp. )
 |
Touch the slider to change color temperature. |
|
Touch dimming slider to change the brightness from 1~100%. |
|
Touch master ON, turn on all linked lights. Long press 5 seconds to turn ON the indicating sound. |
|
When the light is ON, press “60S Delay OFF”, the light will be OFF Automatically after 60 seconds. |
|
Touch master OFF, turn off all linked lights. Long press 5 seconds to turn OFF the indicating sound. |
|
Touch Zone ON, turn on zone-linked lights. |
|
Touch Zone OFF, turn off zone-linked lights. |
B3 & T3
4-Zone Panel Remote Contoller ( RGBW )
 |
Touch color slider, choose the color you want. |
 |
Touch dimming slider to change the brightness from 1~100%. |
 |
Touch white button to white light mode. |
 |
Switching modes. |
 |
Slow the speed on present dynamic mode. |
 |
Accelerate the speed on present dynamic mode. |
|
ALL ON: Touch to turn on all linked lights. Long press 5 seconds to turn ON the indicating sound. Zone(1-4) ON: Touch zone ON, turn on zone-linked lights. |
|
ALL OFF: Touch to turn off all linked lights. Long press 5 seconds to turn OFF the indicating sound. Zone(1-4) OFF: Touch zone OFF, turn off zone-linked lights. |
B4 & T4
4-Zone Panel Remote Contoller ( RGB+CCT )
 |
Touch color slider, choose the color you want. |
 |
Under white light mode, adjust color temperature; Under color light mode, change color saturation. |
|
Touch dimming slider to change the brightness from 1~100%. |
|
Touch white button to white light mode. |
|
Switching modes. |
|
Slow the speed on present dynamic mode. |
|
Accelerate the speed on present dynamic mode. |
|
ALL ON: Touch to turn on all linked lights. Long press 5 seconds to turn ON the indicating sound. Zone(1-4) ON: Touch zone ON, turn on zone-linked lights. |
|
ALL OFF: Touch to turn off all linked lights. Long press 5 seconds to turn OFF the indicating sound. Zone(1-4) OFF: Touch zone OFF, turn off zone-linked lights. |
Link / Unlink (B1&T1,B2&T2,B4&T4)
Linking Instructions
- Switch off the light, after 10 seconds switch on again.
- When the light on, short press any zone of “
” 3 times within 3 seconds.
- The light blink 3 times slowly means the linking is done successfully.
If the light not blink slowly, the linking failed, pls switch off the light again, and follow the above steps again.
Unlinking Instructions
- Switch off the light, after 10 seconds switch on again.
- When the light on, short press any zone of 1 times within 3 seconds.
- The light blink 3 times slowly means the linking is done successfully.
If the light not blink slowly, the linking failed, pls switch off the light again, and follow the above steps again.
Link / Unlink (B3&T3)
Linking Instructions
- Switch off the light, after 10 seconds switch on again.
- When the light on, short press any zone of 1 times within 3 seconds.
- The light blink 3 times slowly means the linking is done successfully.
If the light not blink slowly, the linking failed, pls switch off the light again, and follow the above steps again.
Unlinking Instructions
- Switch off the light, after 10 seconds switch on again.
- When the light on, long press ” ” within 3 seconds.
Unlinking must be the same zone with the Linking
- The light blinking 10 times quickly, means the unlinking successfully.
If the light not blink quickly, the unlink failed, pls switch off the light again, and follow the above steps to unlink again.
Attention
- Please check the cable, and make the circut is correct before power on.
- When installation, pls handle with care to avoid the broken of the glass panel.
- Please do not use lighting fixtures around the mental area and high magnetic field, otherwise, it will badly affect the control distance.
Made in China
Documents / Resources
 | Panel Remote Controller |
References
- User Manualmanual.tools
hello, i have provided the entire ceiling with leds and milight leds, now via the app i have 9 different modes that i can use it is possible to change the modes, e.g. the white lights up and down in modes 5, I would like this in blue, but if I set it to blue it just flashes
guten tag , ich habe bom grundsatz her die komplette decke mit leds und milight leds versehen , habe jetzt über die app 9 verschiedene modis , die ich verwenden kann besteht die möglichkeit die modis zu ändern wie z.b leuchtet das weiße in modi 5 auf und ab , dies hätte ich gerne in blau , wenn ich es aber auf blau stelle blinkt es nur
guten tag , ich habe bom grundsatz her die komplette decke mit leds und milight leds versehen , habe jetzt über die app 9 verschiedene modis , die ich verwenden kann besteht die möglichkeit die modis zu ändern wie z.b leuchtet das weiße in modi 5 auf und ab , dies hätte ich gerne in blau , wenn ich es aber auf blau stelle blinkt es nur
How can I customize the colors within the 9 preset dynamic modes, and why does the light flash when I try to set it to blue?
Based on the MiBOXER Panel Remote Controller manual, the 9 dynamic modes are pre-programmed into the LED controller and cannot be individually edited or redefined (e.g., you cannot change the specific colors used in 'Mode 5' from white to blue).
Regarding the flashing issue when you select blue:
If you want a 'breathing' blue effect (up and down) similar to what you saw with white, you must check if one of the other 9 built-in modes already uses blue. You can cycle through these using the Mode button and adjust the speed using the S+ and S- (Speed) buttons.
Read the full Q&A page
Well done, soon I’m desperate for the normal instructions
Thank you for your work
Super gemacht, bin bald verzweifelt an der normalen Anleitung
Vielen Danke für Eure Arbeit
Thank you for your work<e/em>
Super gemacht, bin bald verzweifelt an der normalen Anleitung
Vielen Danke für Eure Arbeit
How do I use and install the MiBOXER Panel Remote Controller?
It is common to find the printed manuals for these controllers a bit complex. Here is a simplified guide to the most critical operations for the MiBOXER Panel Remote Controller (T1/T2/T3/T4 and B1/B2/B3/B4):
1. Linking Your Lights (Pairing)
2. Unlinking Your Lights
3. Installation Tips
4. Sound Settings
If you find the "beep" sound annoying or want to enable it, you can long-press the Master ON or Master OFF button for 5 seconds to toggle the indicating sound on or off.
Read the full Q&A page