100W Single Output Switching Power Supply
PLC-100 series
GTIN CODE
MW Search: https://www.meanwell.com/serviceGTIN.aspx
Features:
- Universal AC input / Full range
- High efficiency up to 88.5%
- Protections: Short circuit / Over current / Over voltage / Over temperature
- Cooling by free air convection
- Built-in active PFC function
- Class 2 power unit
- Pass LPS
- 100% full load burn-in test
- High reliability
- Suitable for LED lighting and moving sign applications
- Compliance to worldwide safety regulations for lighting
- 2 years warranty
SPECIFICATION
| MODEL | PLC-100-12 | PLC-100-15 | PLC-100-20 | PLC-100-24 | PLC-100-27 | PLC-100-36 | PLC-100-48 | ||
| OUTPUT | DC VOLTAGE | 12V | 15V | 20V | 24V | 27V | 36V | 48V | |
| CONSTANT CURRENT REGION Note.4 | 9 ~ 12V | 11.25 ~ 15V | 15 ~ 20V | 18 ~ 24V | 20.25 ~ 27V | 27 ~ 36V | 36 ~ 48V | ||
| RATED CURRENT Note.6 | 5A | 5A | 4.8A | 4A | 3.55A | 2.65A | 2A | ||
| CURRENT RANGE Note.6 | 0 ~ 5A | 0 ~ 5A | 0 ~ 4.8A | 0 ~ 4A | 0 ~ 3.55A | 0 ~ 2.65A | 0 ~ 2A | ||
| RATED POWER Note.6 | 60W | 75W | 96W | 96W | 95.85W | 95.4W | 96W | ||
| RIPPLE & NOISE (max.) Note.2 | 150mVp-p | 150mVp-p | 150mVp-p | 150mVp-p | 150mVp-p | 150mVp-p | 200mVp-p | ||
| VOLTAGE ADJ.RANGE(VoADJ) | 10.2 ~ 12V | 12.8 ~ 15V | 17 ~ 20V | 20.4 ~ 24V | 23 ~ 27V | 30.6 ~ 36V | 40.8 ~ 48V | ||
| CURRENT ADJ. RANGE(IoADJ) | 3.75 ~ 5A | 3.75 ~ 5A | 3.6 ~ 4.8A | 3 ~ 4A | 2.6 ~ 3.55A | 2 ~ 2.65A | 1.5 ~ 2A | ||
| VOLTAGE TOLERANCE Note.3 | ±3.0% | ±3.0% | ±3.0% | ±3.0% | ±3.0% | ±2.0% | ±2.0% | ||
| LINE REGULATION | ±1.0% | ||||||||
| LOAD REGULATION | ±2.0% | ||||||||
| SETUP, RISE TIME | 500ms, 80ms/230VAC 1200ms, 80ms/115VAC at full load | ||||||||
| HOLD UP TIME (Typ.) | 60ms/230VAC 16ms/115VAC at full load | ||||||||
| INPUT | VOLTAGE RANGE Note.5 | 90 ~ 264VAC 127 ~ 370VDC | |||||||
| FREQUENCY RANGE | 47 ~ 63Hz | ||||||||
| POWER FACTOR (Typ.) | PF>0.95/115VAC, PF>0.95/230VAC at full load (Please refer to “Power Factor Characteristic” curve) | ||||||||
| TOTAL HARMONIC DISTORTION | THD< 20% when output loading¾75% at 115VAC/230VAC input | ||||||||
| EFFICIENCY (Typ.) | 83% | 87% | 88.5% | 88.5% | 88% | 88% | 88.5% | ||
| AC CURRENT (Typ.) | 12V:0.8A/115VAC 0.4A/230VAC 15V:0.9A/115VAC 0.45A/230VAC 20V ~ 48V:1.1A/115VAC | 0.55A/230VAC | |||||||
| INRUSH CURRENT (Typ.) | COLD START 40A(twidth=950μs measured at 50% Ipeak) at 230VAC | ||||||||
| MAX. No. of PSUs on 16A CIRCUIT BREAKER | 3 units (circuit breaker of type B) / 5 units (circuit breaker of type C) at 230VAC | ||||||||
| LEAKAGE CURRENT | <0.75mA / 240VAC | ||||||||
| PROTECTION | OVER CURRENT (Typ.) Note.4 | 95 ~ 102% | |||||||
| Protection type : Constant current limiting, recovers automatically after fault condition is removed | |||||||||
| OVER VOLTAGE | 13 ~ 16V | 16.5 ~ 20V | 22 ~ 27V | 27 ~ 34V | 30 ~ 36V | 39 ~ 48V | 52 ~ 64V | ||
| Protection type : Shut down and latch off o/p voltage, re-power on to recover | |||||||||
| OVER TEMPERATURE | Shut down o/p voltage, re-power on to recover | ||||||||
| ENVIRONMENT | WORKING TEMP. | -30 ~ +50℃ (Refer to “Derating Curve”) | |||||||
| WORKING HUMIDITY | 20 ~ 95% RH non-condensing | ||||||||
| STORAGE TEMP., HUMIDITY | -40 ~ +80℃, 10 ~ 95% RH | ||||||||
| TEMP. COEFFICIENT | ±0.03%/℃ (0 ~ 50℃) | ||||||||
| VIBRATION | 10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes | ||||||||
| SAFETY & EMC | SAFETY STANDARDS Note.7 | UL1310, TUV BS EN/EN60950-1, BS EN/EN61347-1, BS EN/EN61347-2-13, GB19510.14, GB19510.1, CAN/CSA C22.2 No. 223-M91(except for 48V), EAC TP TC 004 approved | |||||||
| WITHSTAND VOLTAGE | I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC | ||||||||
| ISOLATION RESISTANCE | I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH | ||||||||
| EMC EMISSION | Compliance to BS EN/EN55015, GB/T 17743, GB17625.1, BS EN/EN61000-3-2,-3, Class C (¾70% load) ; BS EN/EN61000-3-3, EAC TP TC 020 | ||||||||
| EMC IMMUNITY | Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN61547, BS EN/EN55035, light industry level, (surge 4KV), EAC TP TC 020 | ||||||||
| OTHERS | MTBF | 2688.3K hrs min. Telcordia SR-332 (Bellcore) ; 297.9Khrs min. MIL-HDBK-217F (25℃) | |||||||
| DIMENSION | 200.5*69.5*35mm (L*W*H) | ||||||||
| PACKING | 0.52Kg; 25pcs/14Kg/0.65CUFT | ||||||||
| NOTE | 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Please refer to “DRIVING METHODS OF LED MODULE”. 5. Derating may be needed under low input voltage. Please check the static characteristics for more details. 6. This is the maximum possible output current and power. Over load protection may be activated slightly below this level to comply with the requirement of UL1310 class 2. 7. Safety and EMC design refer to BS EN/EN60598-1, subject 8750(UL), CNS15233, GB7000.1, FCC part18. 8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf) 9. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains. 10. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft). 11. PLC-100-12 is used for any light source that exempt from the ErP-Directive (EU) 2019/2020 requirement, for example this model could be use for signalling products (including, but not limited to road-, railway-, marineorair traffic-signalling , traffic control or airfield lamps). ※ Product Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx |
||||||||
Mechanical Specification
Power Factor Characteristic
EFFICIENCY vs LOAD (48V Model)
PLC-100 series possess superior working efficiency that up to 88.5% can be reached in field applications.
DRIVING METHODS OF LED MODULE
There are two major kinds of LED drive method “direct drive” and “with LED driver”.
A typical LED power supply may either work in “constant voltage mode (CV) or constant current mode (CC)” to drive the LEDs.
Mean Well’s LED power supply with CV+ CC characteristic can be operated at both CV mode [with LED driver, at area (A)] and CC mode [direct drive, at area (B)].
In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems.
Should there be any compatibility issues, please contact MEAN WELL.
http://www.meanwell.com.cn/Upload/PDF/LED_EN.pdf
Downloaded from Arrow.com.
Documents / Resources
 |
MEAN-WELL PLC-100-12 Series Single Output Switching Power Supply [pdf] Owner's Manual PLC-100-12, PLC-100-15, PLC-100-20, PLC-100-24, PLC-100-27, PLC-100-36, PLC-100-48, PLC-100-12 Series Single Output Switching Power Supply, PLC-100-12 Series, Single Output Switching Power Supply, Output Switching Power Supply, Switching Power Supply, Power Supply |