Outsunny Double Rattan Sun Lounger
Model Numbers: 862-006, 862-007
Document ID: IN221100778V01_GL
Introduction
Thank you for purchasing this Outsunny Double Rattan Sun Lounger. This manual provides essential information for assembly, safe use, and maintenance. Please read all instructions carefully before proceeding.
IMPORTANT: Retain for future reference. Read carefully.
This product is intended for domestic use only.
Estimated assembly time: ⏱️ 120MIN. Maximum weight capacity: ⚖️ 220kg.
Parts List
The product consists of the following parts. Please check against the list before assembly.
| Identifier | Description | Quantity |
|---|---|---|
| A | Long frame piece with curved supports | 1 |
| B | Side frame with vertical supports | 1 |
| C | Long frame piece with multiple connection points | 1 |
| D | Frame piece with two rectangular openings | 2 |
| E | Frame piece with angled supports | 1 |
| F | Frame piece with angled supports and central connection | 1 |
| G | Long, thin support bar | 2 |
| H | Frame piece with multiple connection points and a central divider | 1 |
| I | Base frame with integrated support structure | 1 |
| J | Frame piece with integrated support structure | 1 |
| K | Frame piece with integrated support structure | 1 |
| L | Frame piece with integrated support structure | 1 |
| M | Frame piece with angled supports | 1 |
| N | Frame piece with angled supports | 1 |
| Y | Rectangular cushion/seat base | 2 |
| Z1 | Rectangular cushion/seat base | 2 |
| Z2 | Rectangular cushion/seat base | 2 |
| Hardware Kit | Bag containing various screws, bolts, nuts, and washers | 1 |
Hardware List
The following hardware is included. Please check quantities carefully.
| Identifier | Description | Quantity |
|---|---|---|
| O | Bolt M6*35 | 14 |
| P | Bolt M6*30 | 20 |
| Q | Bolt M6*52 | 6 |
| R | Bolt M6*15 | 8 |
| S | Bolt M6*40 | 4 |
| T | Bolt M6*45 | 4 |
| U | Washer M6 | 66 |
| V | Nut M6 | 10 |
| W | Wrench | 1 |
| X | Wrench | 1 |
Assembly Instructions
General Note: Do not confuse similar screws. Do not tighten bolts fully until all parts are connected! ?️
Step 1
Connect Part A (long frame) to Part B (side frame) using 5x Bolt (O) ? and 5x Washer (U). Connect Part C (long frame) to Part B using 5x Bolt (O) ? and 5x Washer (U).
Diagram shows Part A and Part C being attached to Part B, forming a U-shape. Close-up shows Bolt (O) and Washer (U).
Step 2
Attach two Part D (frame with openings) to the assembled structure using 6x Bolt (P) ? and 6x Washer (U) for each.
Diagram shows two Part D pieces being attached to the frame. Close-up shows Bolt (P) and Washer (U).
Step 3
Attach Part E (angled frame) using 2x Bolt (O) ? and 2x Washer (U). Attach Part F (angled frame) using 2x Bolt (Q) ?, 6x Washer (U), and 2x Nut (V) ?.
Diagram shows Part E and Part F being attached. Close-ups show hardware for E (O, U) and F (Q, U, V).
Step 4
Attach Part G (long support bar) using 4x Bolt (R) ? and 4x Washer (U).
Diagram shows Part G being attached to the frame. Close-up shows Bolt (R) and Washer (U).
Step 5
Attach Part H (frame with divider) using 4x Bolt (P) ? and 4x Washer (U).
Diagram shows Part H being attached. Close-up shows Bolt (P) and Washer (U).
Step 6
Attach Part I (base frame) using 2x Bolt (S) ? and 2x Washer (U).
Diagram shows Part I being attached. Close-up shows Bolt (S) and Washer (U).
Step 7
Attach Parts J, K, and L (support frames). For Part J, use 5x Bolt (O) ? and 5x Washer (U).
Diagram shows Parts J, K, and L being attached to the main structure. Close-up shows Bolt (O) and Washer (U) for Part J.
Step 8
Attach another Part D (frame with openings) using 6x Bolt (P) ? and 6x Washer (U).
Diagram shows another Part D piece being attached. Close-up shows Bolt (P) and Washer (U).
Step 9
Attach Part N (angled frame) using 2x Bolt (Q) ?, 6x Washer (U), and 2x Nut (V) ?. Attach Part M (angled frame) using 2x Bolt (O) ?, 6x Washer (U), and 2x Nut (V) ?.
Diagram shows Parts M and N being attached. Close-ups show hardware for N (Q, U, V) and M (O, U, V).
Step 10
Attach Part G (long support bar) using 4x Bolt (R) ? and 4x Washer (U).
Diagram shows Part G being attached. Close-up shows Bolt (R) and Washer (U).
Step 11
Attach Part H (frame with divider) using 4x Bolt (P) ? and 4x Washer (U).
Diagram shows Part H being attached. Close-up shows Bolt (P) and Washer (U).
Step 12
Attach Part I (base frame) using 2x Bolt (S) ? and 2x Washer (U).
Diagram shows Part I being attached. Close-up shows Bolt (S) and Washer (U).
Step 13
Final assembly. Secure seat bases Y, Z1, Z2. Use 2x Bolt (Q) ?, 6x Nut (V) ?, and 12x Washer (U) for frame connections. Use 4x Bolt (T) ? and 12x Washer (U) for seat base attachments.
Diagram shows the final placement of seat bases Y, Z1, Z2. Close-ups show hardware connections.
Final Tightening: Once all parts are assembled, go back and fully tighten all bolts and screws. ?
Usage Tips
- Place the lounger stably on a flat floor.
- Mount the lounger in a sheltered area, away from direct sun and rain.
- Stay away from open flames.
- Do not hang anything on the structure.
- Do not overload the anchors/structure. The maximum weight capacity is ⚖️ 220kg.
- It is advised not to stay on the lounger during a storm.
- Do not use in adverse weather conditions and cover the furniture when not in use.
Maintenance and Storage
Maintenance
- Clean with a soft fabric.
- Regularly remove leaves and/or water collected on the fabric.
- Check the lounger regularly for any loose parts or damage.
- Do not use this product if the seat cloths, cushions, or tarpaulins are ageing.
Storage Conditions
- When not in use, the furniture should be stored completely dry in a clean and dry place to avoid the risks of mold.
- Cover the furniture with an appropriate cover when not in use.
Safety Precautions
- Prepare a clean and dry assembly area.
- Verify that the product is not damaged before assembly.
- Check that none of the pieces are missing.
- Caution: Risk of pinching or cuts during assembly. Handle parts with care.
The manufacturer declines all responsibility in case of damages due to a bad installation or due to weather conditions.
Contact Information
If you have any questions, please contact our customer care center.
| Country | Phone | |
|---|---|---|
| UK | 0044-800-240-4004 | enquiries@mhstar.co.uk |
| DE | 0049-0(40)-88307530 | service@aosom.de |
| FR | 0033-1-84166106 | aosom@mhfrance.fr |
| ES & PT | 0034-931294512 | atencioncliente@aosom.es |
| IT | 0039-0249471447 | clienti@aosom.it |
| US | 001-877-644-9366 | customerservice@aosom.com |
| CA | 416-792-6088 | customerservice@aosom.ca |
Importer Information
US Importer: Aosom LLC, 27150 SW Kinsman Rd Wilsonville, OR 97070 USA. Made in China.
CA Importer: Aosom Canada Inc., 1251 Tapscott Road, Unit 101, Scarborough, Ontario Canada M1X 1S9. Made in China.
UK Importer: MH STAR UK LTD, Unit 27, Perivale Park, Horsenden lane South, Perivale, UB6 7RH. Made in China.
FR Importateur: MH FRANCE, 2 Rue Maurice Hartmann, 92130 Issy Les Moulineaux, France. Fabriqué en Chine.
ES Importador: SPANISH AOSOM, S.L., C/ ROC GROS, N° 15. 08550, ELS HOSTALETS DE BALENYÀ, SPAIN. B66295775. Tel: 931294512. Atencioncliente@aosom.es. Hecho en China.
DE Importeur: MH Handel GmbH, Wendenstraße 309, D-20537 Hamburg, Germany. In China hergestellt.
IT Importato da: AOSOM Italy srl, Centro Direzionale Milanofiori, Strada 1 Palazzo F1, 20057 Assago (MI). P.I.: 08567220960. Fatto in Cina.
