Introduction
Thank you for choosing our Wireless Doorbell. This manual provides detailed instructions to ensure a smooth setup and optimal usage of your device. The doorbell utilizes advanced technology for accurate signal detection, aiming to enhance your living quality and simplify your daily routine. It is designed with a focus on high quality and competitive performance.
The wireless transmitter and plug-in receiver boast an impressive 300-400m range in open areas, making them suitable for various environments such as homes, apartments, offices, classrooms, and hospitals.
Expandability is a key feature, allowing the receiver to pair with up to 58 different transmitters. Each transmitter can be customized with one of 58 available ringtones, enabling easy identification of the signal's origin in different locations.
Overview
1. Plug-in Receiver
The receiver features an LED indicator on the front, with three buttons on the side: Up Button, Down Button, and Volume Button. The AC plug and speaker are located on the back.
2. Transmitter/Push Button
The transmitter/push button has a rubber surface with an illuminated LED that lights up when pressed.
Technical Specification
| Receiver working voltage | AC100V-240V |
| Sound pressure level | < 110dB |
| Receiver AC power consumption | < 0.25 W (standby mode) |
| Working frequency | 433.92 MHz |
| Transmitter battery type | A23 12V Alkaline Battery |
| Operating temperature | -20 °C-60 °C |
| Battery lifetime | 1-3 years |
| Wireless range | 300-400M (in open area) |
| Waterproof | IP55 |
Operating Instructions
- Powering the Indoor Chime Receiver: Plug the receiver into an electrical outlet. For best performance, keep it away from other electrical equipment like TVs or microwaves.
- Powering the Transmitter: Remove the insulating sheet from the battery. Press the button to confirm it is working (the button should flash blue).
- Sound Volume Control: Use the volume control button on the receiver to cycle through five volume levels, including a mute mode.
- Pairing a Transmitter to Receiver:
- Select your preferred ringtone before pairing.
- Long press the Volume button for 5 seconds (or short press the Volume and Down buttons together) until a 'Ding-dong' sound is heard and the LED indicator flashes, indicating pairing mode.
- Press the transmitter button to send a signal. Successful pairing (ringtone sync) will result in the receiver playing the selected ringtone automatically.
- Setting Ringtone: There are 58 ringtones available. Use the Up or Down buttons on the receiver to select your desired ringtone. Follow pairing steps (2) and (3) to sync the new ringtone with the transmitter. The ringtone can be set differently for each transmitter.
- Two or More Transmitters Pairing: Repeat Step 4 to pair additional transmitters.
- Reset: Press and hold the Down button for 5 seconds to reset the receiver to default settings. A 'Ding Dong' sound and flashing LED confirm a successful reset. You can then follow Step 4 to pair again.
Please Note: Pairing mode lasts for 5 seconds. Ensure the transmitter is activated within this time frame to avoid restarting the process.
Installation
Transmitter Battery Installation
The battery is pre-installed. Insert a screwdriver into the designated slot and twist clockwise to open. Peel off the insulating film from the button cell, then close the cover. Always observe battery polarity when replacing.
Transmitter Installation
- Adhesive Tape: Apply the double-sided adhesive tape to the back of the transmitter. Remove the protective backing and attach the transmitter to the desired wall location, pressing firmly for 30 seconds. Ensure the wall surface is clean before installation.
- Screws and Anchors: Knock out the screw locator points on the back of the transmitter. Use screws and anchors to fix the transmitter securely to the wall in the desired location.
Troubleshooting
| Problem | Cause | Solution |
|---|---|---|
| Indicator on transmitter does not light up | Battery insulating film not removed | Peel off the insulating film. |
| Battery not installed properly | Remove and reinstall the battery, ensuring good contact. | |
| Low battery power | Replace with a new battery. | |
| Receiver does not respond to transmitter | Unsuccessful pairing | Pair the transmitter and receiver again. |
| Receiver lights up but no sound | Mute mode is ON | Press the Volume Button to enable sound. |
Warranty and After-Sale Service
A 24-month warranty is provided for this product. For any questions or issues during use, please do not hesitate to contact us via your order details or our 24-hour email support.
