Wireless Doorbell User Manual

Product Overview

The wireless doorbell system consists of a receiver (indoor unit) and a transmitter (outdoor unit). It offers a simple and flexible installation without the need for wiring.

Product Diagram

AC Receiver: Features a plug, volume buttons (backward, forward), speaker, and LED light.

Transmitter: Includes a push button and LED light. It is designed to be mounted outdoors.

Specification

Product Features

• Transmitter Waterproof Grade: IP55
• Ring-tones: 38/55 options
• Volume: Level 5 Adjustable, 0-110 dB
• Memory Function
• Control Distance: 150-300 Meters (barrier-free)

Installation

For AC Receiver: Plug the receiver into a mains socket and switch the socket on.

For Transmitter: Pull out the white insulating strip from the transmitter. Mount the transmitter in the desired location. With doors closed, press the transmitter button to confirm the receiver sounds. If it doesn't, reposition the transmitter or receiver. Secure the transmitter using the provided double-sided adhesive tape or screws.

Change the Ring-tone/Pairing

The default ring-tone is 'Ding Dong'. To change it or pair new transmitters/receivers:

1. Step 1: Short press the Backward or Forward button on the receiver to select your preferred music. The receiver will play the selected music.
2. Step 2: Long press the Volume button on the receiver for approximately 5 seconds until it emits a single 'Ding' sound and the LED light flashes.
3. Step 3: Within 8 seconds, press the button on the transmitter. The receiver will emit two 'Ding' sounds and the LED light will flash, indicating successful pairing. This learning mode is active for 8 seconds.
4. Step 4: Press the transmitter button again to confirm if the current ringtone is the one you set. If it is, the pairing is complete.

Remark: This procedure is used for changing ringtones, adding new transmitters, or re-pairing existing ones.

Clear Settings

Long press the Forward button on the receiver for about 5 seconds until it emits a single 'Ding' sound and the LED light flashes. This action will clear all settings, including the selected ringtone and paired transmitters/receivers.

After clearing, pressing the transmitter button will automatically pair the first transmitter. Other transmitters will need to be re-paired.

Troubleshooting

If the doorbell is not working, consider the following:

• Ensure the receiver is paired with the transmitter. Refer to the pairing steps.
• Verify that the AC receiver is switched on at the mains.
• Check for potential sources of electrical interference near the transmitter or receiver, such as power adapters or other wireless devices.
• Obstacles like walls can reduce the range. This should have been considered during setup.
• Ensure no metal objects are placed between the transmitter and receiver. Repositioning may be necessary.

Cautions

• The doorbell receiver is intended for indoor use only. Do not expose it to moisture or use it outdoors.
• Avoid placing the transmitter in direct sunlight or rain.
• Use only high-quality batteries for the transmitter.

FCC Caution

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Packing List

The package includes: Transmitter, Receiver, 23A 12V Alkaline Battery, User Manual, Double Sided Adhesive Tape, Mini Screw Driver.