Perlegear PGFS03 / PGFS03W TV Stand Instruction Manual

Before Assembly: Check TV Compatibility

Ensure your TV's hole spacing is within 600 x 400mm or greater than 200 x 100mm.

Minimum VESA standard: 200mm x 100mm.

Check if your TV (including accessories) weighs less than 40 kg.

Required Tools (Sold Separately):

Important Notes:

• Read this manual carefully before use and use it correctly. If you have any questions, please contact your seller or a professional installer.
• Some parts are included in excess for loss prevention; spare parts are extra.
• Ignoring warnings may result in material damage or injury.
• Do not use the product for purposes other than those described in the manual. Do not exceed the maximum load capacity. Perlegear is not responsible for accidents or damage due to improper installation or handling.
• Before assembly, confirm all parts are present and undamaged. Contact us if any parts are missing or damaged.
• Warning: Contains small parts. Keep away from children to prevent accidental ingestion and suffocation.

Parts List

• M4 / M5 Washers [B1] x 4
• M6 / M8 Washers [B2] x 4
• Spacers [F1] (2.5mm) x 8
• Spacers [F2] (10mm) x 4
• Spacers [F3] (22mm) x 4
• M4 x 12mm Bolts [C1] x 4
• M4 x 30mm Bolts [C2] x 4
• M6 x 15mm Bolts [D1] x 4
• M6 x 35mm Bolts [D2] x 4
• M8 x 15mm Bolts [E1] x 4
• M8 x 35mm Bolts [E2] x 4
• M8 x 50mm Bolts [E3] x 4
• Glass Plate [01] x 1
• Support Column [02] x 1
• TV Plate [03] x 1
• Left Bracket [04-L] x 1
• Right Bracket [04-R] x 1
• Foot Pads [G] x 6
• Plastic Cover [H] x 1
• Brass Washer [I] x 3
• Steel Washer [J] x 3
• M6 x 25mm Bolt [K] x 3
• Hex Wrench [O] x 1
• M6 x 45mm Bolt [L] x 4
• M6 x 12mm Bolt [M] x 1
• Cable Management Clip [N] x 2

Step 1: Attach Brackets to TV

Step 1-1: Select TV Bolts

Manually screw the bolts into the threaded holes on the back of your TV to determine the correct size (M4, M6, or M8).

Bolt Selection Guide:

• Incorrect: Bolts that are too short, too long, or cause cracking.
• Correct: Bolts that thread in smoothly and securely, with appropriate washers.

Step 1-2: Confirm Parts for Your TV

Select the appropriate spacers and bolts based on your TV's back panel design.

Step 1-3: Attach Brackets to TV

Option A (Flat Back TV): Use bolts [C1/D1/E1] with washers [B1/B2].

Option B (Curved Back TV): Use spacers [F1/F2/F3] to ensure clearance between the bracket and the TV's curve.

Option C (Recessed Back TV): Ensure the bracket is flush with the recess using appropriate spacers.

Option D (Interfering Ports): Use spacers [F1/F2/F3] to create extra space for cable connections.

Option E (Protruding Back): Use spacers [F1/F2/F3] to fill gaps and ensure the bracket is flush.

Attach brackets [04-L] and [04-R] to the TV using the selected bolts and washers. Ensure the brackets are oriented correctly (L for left, R for right) and the 'UP' indicator is facing upwards.

Note: Do not overtighten screws.

Step 2: Attach the Base

Step 2-1: Attach Foot Pads

Adhere the foot pads [G] to the four corners on the bottom of the glass plate [01].

Caution: Ensure the tempered glass base is placed with the glossy side facing up.

Step 2-2: Prepare Support Column

Ensure the upper support column is not extended before proceeding.

Step 2-3: Attach Support Column to Base

Using the plastic cover [H], plastic washer [I], steel washer [J], bolt [K], and hex wrench [O], attach the support column [02] to the tempered glass base [01].

Caution: Do not overtighten screws.

Step 2-4: Adjust Height

Pull the knob outwards and lift the upper support column. The upper column will automatically lock into the lower column. Check that the upper support column operates correctly.

Note: The upper support column offers 6 height adjustment positions.

Step 4: Mount TV to TV Plate

Confirm the desired height position for the TV on the TV plate [03] before mounting.

Follow steps 4-1 to 4-3 for initial mounting and height adjustment.

Step 4-1: Adjust TV Height

Pull the knob outwards and move the TV up or down to your desired height. The TV can be rotated left and right if needed.

Step 4-2: Hang Brackets on TV Plate

Hook the brackets onto the center of the TV plate [03]. Slightly loosen the pre-assembled bolts on the brackets.

Step 4-3: Secure Brackets

Tighten the bolts [M] using the hex wrench [O] until they are snug against the TV plate.

Note: The TV plate does not have bolt holes.

Caution: Two people are recommended for this step.

Step 6: Left/Right Adjustment

The TV plate can be rotated left and right as needed.

Use the cable management clips [N] to secure cables along the support column.