Perlegear PGTVMC14 TV Cart Instruction Manual

Before getting started, let's make sure this cart is compatible.

1. Is the VESA pattern of your TV 100 x 100mm (3.9" x 3.9") to 400 x 400mm (15.7" x 15.7")?

   ✔️ Yes - Perfect!

   ❌ No - This TV cart is NOT compatible.

2. Does your TV (including accessories) weigh less than 88 lbs (40kg)?

   ✔️ Yes - Perfect!

   ❌ No – This TV cart is NOT compatible.

3. Tools Needed (NOT Included): Phillips Screwdriver

4. Important Safety Information

   NOTE: Please carefully read all instructions before attempting installation. If you DO NOT understand the instructions or have any questions or concerns, please call technical support or email customer service. Not all hardware included in this package will be used.

   CAUTION: Avoid the risk of personal injury and property damage! DO NOT use this product for any purpose that is NOT explicitly specified in this manual. DO NOT exceed weight capacity. Perlegear is NOT liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

   Before starting assembly, verify all parts are included and undamaged. DO NOT use damaged or defective parts. If you require replacement parts, please call technical support or email customer service.

   WARNING: This package contains small parts that may pose a choking hazard.

   TIP-OVER WARNING: Serious or fatal crushing injuries can occur from a tip-over accident. To help prevent a tip-over accident:

   • Never allow children to climb, stand, hang, or play on any part of the TV or TV cart.
   • Use tip-over restraints (not included) or anchors (not included) to attach the TV cart to the wall.
   • Tip-over restraints may reduce but not eliminate the risk of a tip-over accident.

Supplied Parts and Hardware

• Washer M4/M5 [B1] x 4
• Washer M6/M8 [B2] x 4
• Spacer L2.5mm [F1] x 4
• Spacer L10mm [F2] x 8
• TV Bolt M4 x 12mm [C1] x 4
• TV Bolt M4 x 30mm [C2] x 4
• TV Bolt M6 x 15mm [D1] x 4
• TV Bolt M6 x 35mm [D2] x 4
• TV Bolt M8 x 15mm [E1] x 4
• TV Bolt M8 x 35mm [E2] x 4
• Right TV Bracket [R] x 1
• Left TV Bracket [L] x 1
• Base Section [01] x 1
• Long Square Tube [02] x 2
• Short Square Tube [03] x 2
• Caster [04] x 4
• 35/64" (14mm) Wrench [04-1] x 1
• Lower Pole [05] x 2
• Middle Pole [06] x 2
• Upper Pole [07] x 2
• Pole Connector [08] x 8
• TV Plate [10] x 1
• M6 x 10mm Bolt [a] x 14
• 6 x 16 x 1.5mm Washer [b1] x 8
• M6 x 55mm Bolt [c] x 12
• Nut M6 [b2] x 12
• Cable Clip [e1] x 4
• 5/32" (4mm) Allen Key [e2] x 1
• 7/16" (11mm) Wrench [e3] x 1

Step 1 Attach TV Brackets to TV

1. 1-1 Select TV Bolts

   Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt (M4, M6 or M8) to use. A minimum of 4–5 turns into the threading is required. Do not turn past the bottom of the hole.

2. 1-2 Spacer and Bolt Configurations

   Diagrams illustrating different TV back types: Flat Back TV (See Option A), Curved Back TV (See Option B), TV With a Bump (See Option C), TV With Protruding Cables (See Option D), TV With Recessed Holes (See Option E).

3. 1-3 Attach the TV Brackets to Your TV

   Round holes should be directed toward the top.

   Option A: For Flat Back TVs

   Diagram showing attachment of brackets [R] and [L] to a flat TV back using bolts and optional spacers [F1].

   Add spacers if needed to fit the bolt length and TV back. [DO NOT overtighten]

   Option B: For Curved Back TVs

   Diagram showing attachment of brackets [R] and [L] to a curved TV back using bolts and spacers [F1/F2].

   Spacers must be tall enough so that the curved back of the TV does not interfere with the mounting plate. [DO NOT overtighten]

   Option C: For TVs With a Bump

   Diagram showing attachment of brackets [R] and [L] to a TV back with a bump using bolts and spacers [F1/F2].

   The TV brackets must be flush on the bump and leveled by spacers on the gap. [DO NOT overtighten]

4. Option D: For TVs With Protruding Cables

   Diagram showing attachment of brackets [R] and [L] to a TV back with protruding cables using bolts and spacers [F1/F2].

   Use spacers to create extra space between the TV and TV brackets. [DO NOT overtighten]

5. Option E: For TVs With Recessed Holes

   Diagram showing attachment of brackets [R] and [L] to a TV back with recessed holes using bolts and spacers [F1/F2].

   Spacers need to fill in the recessed holes on the back of the TV, while keeping the TV brackets as close to the TV as possible. [DO NOT overtighten]

Step 2 Install the Base

Insert the long square tubes [02] onto the side of base section [01] with droplet holes. Insert the short square tubes [03] onto the other side. Secure the tubes with bolts [a] and washers [b1].

NOTE: Flip the brakes down to avoid movement during assembly.

Screw the casters [04] into the base using the wrench [04-1].

Step 3 Secure the Poles to the Base

3-1

Insert lower poles [05] into the base and secure with bolts [a] using Allen Key [e2].

3-2

Insert bolts [c] into four pole connectors [08] as the front pole connectors. Keep them for Step 3–3 and Step 3–4.

3-3

Place the middle poles [06] on top of the lower poles [05]. With the front pole connectors attached, pass bolts [c] through the holes and thread them into the other pole connectors [08] on the opposite side. Firmly tighten nuts [b2] using the 7/16" (11mm) Wrench [e3] to secure the poles together. NOTE: The droplet holes in the middle poles should face forward.

3-4

Place the upper poles [07] on top of the middle poles [06]. Repeat steps from 3-3 using the pole connectors [08] to secure the upper and middle poles together.

Step 4 Secure the TV Plate to the Upper Poles

The upper poles [07] have 5 height options. Determine the best height for your TV before moving on to attach your TV to the poles.

Secure the TV plate [10] to the upper poles [07] with bolts [c] and nuts [b2] using Allen Key [e2] and 7/16" (11mm) Wrench [e3].

Step 5 Hang the TV on the TV Plate

Slightly loosen the preassembled bolts on both TV brackets until they are seated flush with the plate.

HEAVY! You may need assistance with this step. Phillips Screwdriver NOT included.

Hang the TV on the TV plate [10]. Retighten the bolts on the brackets until they are pulled firmly against the TV plate.

Step 6 Adjust the Tilt Angle of the TV

Slightly loosen nuts [T]. Adjust the TV to your desired tilt angle. Retighten nuts [T] to lock the tilt angle using the 7/16" (11mm) Wrench [e3].

Step 7 Adjust the Height of the Casters

If the TV cart is not level on the floor, you can adjust the casters by turning the preassembled nuts for proper stability using the 35/64" (14mm) Wrench [04-1].

Step 8 Cable Management

Use cable clips [e1] x 4 to manage cables along the poles.