PERLEGEAR FLOOR TV STAND INSTRUCTION MANUAL

Contact Information

Thank you for choosing Perlegear. For installation questions or issues, please contact us:

• US/CA: 1-800-456-5231 (Mon-Fri, 8am-8pm CST)
• UK: 44-808-196-4165 (Mon-Fri, 2pm-10pm UTC)
• Email: support@perlegear.com
• Website: www.perlegear.com

Parts and Hardware Overview

Refer to the diagrams for identification of parts and hardware.

Parts List:

• 01 TV Bracket (x2)
• 02 Right Wood Base (x1)
• 03 Left Wood Base (x1)
• 04 Middle Wood Base (x1)
• 05 Connector Plate (x1)
• 06 Bottom Cover (x1)
• 07 Lower Support Pillar (x1)
• 08 Middle Support Pillar (x1)
• 09 Upper Support Pillar (x1)
• 10 TV Plate (x1)

Hardware List:

• Bolts: A (M6 x 12mm, x14), B (M8 x 30mm, x3), C1 (M4 x 12mm, x4), C2 (M4 x 30mm, x4), D1 (M6 x 15mm, x4), D2 (M6 x 35mm, x4), E1 (M8 x 15mm, x4), E2 (M8 x 35mm, x4), E3 (M8 x 50mm, x4)
• Washers: B1 (M4/M5), B2 (M6/M8), C (φ8 x φ16 x 1.0mm, x7), F1 (φ11 x φ20 x 2.5mm, x1), F2 (φ11 x φ20 x 1.0mm, x1), G (φ11 x φ20 x 1.0mm, x1), H (φ6.5 x φ12 x 1.0mm, x4)
• Spacers: F1 (L2.5mm, x8), F2 (L10mm, x4), F3 (L22mm, x4)
• Nuts: E (M10, x1), H (M6, x4)
• Foot Pads: J (x6)
• Safety Locks: K (x2)
• Cable Clips: L (x2)
• Tools: M1 (5/32" Allen Key), M2 (3/16" Allen Key), N1 (3/8" Wrench), N2 (11/16" Wrench)

Before Getting Started

1. Check VESA Pattern Compatibility

   Ensure your TV's VESA pattern is compatible. The minimum VESA pattern is 100mm x 100mm (3.9" x 3.9"), and the maximum is 400mm x 400mm (15.7" x 15.7").

   Measurement Conversion: 100mm = 3.9", 200mm = 7.9", 300mm = 11.8", 400mm = 15.7".

   If the stand is not compatible, contact Perlegear Technical Support or Customer Service.

2. Check Max Load

   WARNING: Do not exceed the maximum load capacity of 88 lbs (40kg). Exceeding the limit may cause damage or injury.

3. Tools Needed (Not Included)

   Phillips Screwdriver

4. Important Safety Information

   • Read all instructions before installation. Contact support@perlegear.com for assistance.
   • Not all hardware may be used.
   • CAUTION: Avoid potential injuries and property damage. Do not use the product for purposes not specified in this manual. Perlegear is not liable for damage caused by incorrect assembly, improper mounting, or inappropriate use.
   • Before assembly, check all parts are included and undamaged. Contact support@perlegear.com for replacement parts.
   • WARNING: Contains small parts that may pose a choking hazard.
   • TIP-OVER WARNING: To prevent serious or fatal crushing injuries from tip-over accidents: Never allow children to climb or play on the stand. Use tip-over restraints (not included) to secure the stand to the wall.

   SAVE THESE INSTRUCTIONS.

Installation Steps

1. Step 1: Attaching the TV Brackets to Your TV

   Select TV Bolts: Hand thread bolts (M4, M6, or M8) into the TV's threaded inserts to find the correct fit. Screw in at least five turns, but do not go past the bottom of the hole.

   Spacer and Bolt Configurations:

   • Option A: For Flat Back TVs: Add spacers as needed to fit the bolt length and TV back.
   • Option B: For Curved Back TVs: Use spacers tall enough to prevent interference with the mounting plate.
   • Option C: For TVs with a Bump: Ensure TV brackets are flush on the bump and leveled with spacers.
   • Option D: For TVs with Protruding Cables: Use spacers to create extra space between the TV and brackets.
   • Option E: For TVs with Recessed Holes: Use spacers to fill recessed holes, keeping brackets close to the TV.

   Note: The TV brackets should be equally centered and securely fastened.

2. Step 2: Assembling the Base

   1. Attach the foot pads [J] to the bottom of the wood base, leaving a small gap between the edge and the pads.
   2. Attach the bottom cover [06] and lower support pillar [07] to the wood base using washers [C] and bolts [B]. Note: The raised edge of the base plate should face up. Use Allen Key M1 for this step.

3. Step 3: Attaching the Support Pillar

   1. Connect the middle support pillar [08] to the lower support pillar [07] using bolts [C] and [D] and Allen Key M2.
   2. Attach the upper support pillar [09] to the middle support pillar [08] using bolts [E], [F], [G] and nuts [H] with Wrench N2.

4. Step 4: Securing the TV Plate to the Support Pillar

   Note: There are three height adjustment options. Connect the TV plate [10] to the upper support pillar [09] at your desired height.

   Secure the TV plate using bolts [A] and [I] with Allen Key M1 and Wrench N1.

5. Step 5: Mounting the TV on the TV Plate

   The TV brackets have three sets of hooks (#1, #2, #3) for different height positions. Choose the appropriate hooks before hanging your TV. #1 is lowest, #2 adds height, #3 is highest.

   Note: This step may require assistance due to the weight of the TV.

6. Step 6: Cable Management

   Insert safety locks [K] into the upward-facing hooks below the TV plate and tighten bolts. Use cable clips [L] to manage cables along the support pillar.