Electric Standing Desk Instruction Manual

Specifications

Tools Needed (not included)

• Drill ?
• OR
• Phillips Screwdriver ?+

Supplied Parts and Hardware

Step 1

• Bolt M6 x 11mm (A) x 4
• Bolt M6 x 35mm (B) x 8
• Large Allen Wrench 3/16" (5mm) (C) x 1
• Crossbar (01) x 1
• Left Desk Leg (02) x 1
• Right Desk Leg (03) x 1
• Leg Base (04) x 2

Step 2

• Side Plate (05) x 2
• Transmission Rod (06) x 1
• Bolt M6 x 11mm (A) x 4

Step 3

• Large Allen Wrench 3/16" (5mm) (C) x 1
• Small Allen Wrench 5/64" (2mm) (D) x 1
• Rubber Pad (E) x 10
• Desktop (07) x 1
• Screw M5 x 16mm (F) x 4
• Wood Dowel Pin (G) x 4
• Desktop Panel Connector (H) x 2

Step 4

• Screw M5 x 16mm (F) x 16
• Storage Hook (I) x 2

Step 5

• Cable Clip (J) x 2
• AC Adapter (09) x 1

Step 6

• Cable Hole Cover (K) x 2
• Controller (08) x 1

Assembly Instructions

Step 1: Assembling and Connecting the Desk Legs

Attach the crossbar (01) to the left desk leg (02) and right desk leg (03) using bolts (A) and the large Allen wrench (C). Then, attach the leg bases (04) to the bottom of each leg using bolts (B) and the large Allen wrench (C). Detailed views show the connection points and bolt insertion.

Step 2: Attaching the Side Plates and the Transmission Rod

Attach the side plates (05) to the desk legs (02, 03) using bolts (A) and the large Allen wrench (C). Loosen the coupling nut on the transmission rod mechanism. Insert the transmission rod (06) into the mechanism on the left leg. Measure the heights of both desk legs; if they are not level, turn the transmission rod. Turning clockwise lowers the left leg, and turning anti-clockwise raises it, to match the right leg's height. Ensure the set screw faces outwards. Smoothly connect the other end of the transmission rod to the motor drive shaft on the right leg. Secure the transmission rod to the motor drive shaft by turning the set screw clockwise with the small Allen wrench (D). Tighten the coupling nut to fine-tune the transmission rod fit, using the rubber pads (E) as needed.

Step 3: Assembling the Desktop

Assemble the desktop (07) panels. Insert wood dowel pins (G) into the designated holes. Use desktop panel connectors (H) to join the panels, securing them with screws (F). This assembly can be done using a drill (with suitable torque and speed) or a Phillips screwdriver.

Step 4: Attaching the Desktop

Attach the assembled desktop to the frame (legs and crossbar) using screws (F). This can be done using a drill or a Phillips screwdriver. Then, attach the controller (08) and storage hooks (I) to the underside of the desktop using screws (F).

Step 5: Connecting the Cables

Connect the AC adapter (09) cable to the controller (08). Use cable clips (J) to manage and secure the cables neatly.

Step 6: Installing the Cable Hole Covers

Install the cable hole covers (K) into the designated openings on the desktop.

Using the Controller

The controller features buttons for saving and selecting height settings, as well as raising and lowering the desk.

Controller Interface

The controller display shows settings and status. Buttons include [S] for Save/Settings, [1], [2], [3] for preset heights, [^] to Raise the Desk, and [v] to Lower the Desk.

Height Adjustment Functions

• Save Current Height Setting: Short-press the [S button]. The display will flash. Press the [1], [2], or [3] button to save the current height to that preset.
• Select Height Setting 1: Press the [1 button]. The desk will move to the height previously saved for this setting.
• Select Height Setting 2: Press the [2 button]. The desk will move to the height previously saved for this setting.
• Select Height Setting 3: Press the [3 button]. The desk will move to the height previously saved for this setting.
• Raise the Desk: Press the [^ button] continuously until the desk reaches the highest position of 46.5" (118cm) or until the button is released.
• Lower the Desk: Press the [v button] continuously until the desk reaches the lowest position of 28.3" (72cm) or until the button is released.

Settings

Change Display Height Units

Press and hold the [S button] until a flashing 'S–' is displayed. Press [S] again, and 'Un' is displayed. Press [S] to select. Press [^] or [v] to switch between 'IN' (imperial) and 'SI' (metric). Press [S] to save your choice.

Change Collision Detection Sensitivity

Long press the [S button]; 'S–' shows and flashes. Press [S] again, and the display shows 'Un.' Press [^] or [v] to switch to 'CF.' Press [S] to select. Press [^] or [v] to switch between 'OFF,' Low (L), Normal (n), or Heavy (H) collision force detection. Press [S] to save your choice.

Reset

Press and hold the [v button] for 5 seconds. The screen will show 'RES.' Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes

The desk may enter protection modes or display error codes under certain conditions.