Instruction Manual for MARSAIL models including: TZESD9B, TZESD9V, TZESD9N, TZESD9N Series Electric Standing Desk, TZESD9N Series, Electric Standing Desk, Standing Desk, Desk
Marsail Electric Standing Desk Adjustable Height, Adjustable Desk Stand up Desk for Home Office Furniture Computer Desk Memory Preset with Headphone Hook : Office Products
Electric Standing Desk Instruction Manual Rev00(A) Model: TZESD9B / TZESD9V / TZESD9N Thank you for choosing this product! We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don't hesitate to contact us at service.wowowo@gmail.com. Specifications Height Adjustment Range: 28.346.5 (72-118cm) RATED Power Input Max Speed Operating Noise Max Load 100V-240V 20mm/s 55dB 176 lbs / 80 kg Tools Needed (not included) OR Drill Phillips Screwdriver Supplied Parts and Hardware for Step 1 Crossbar 01 x 1 Left Desk Leg 02 x 1 Leg Base 04 x 2 Bolt M6 x 11mm A x4 Large Allen Wrench 3/16 (5mm) C x1 Supplied Parts and Hardware for Step 2 Side Plate 05 x 2 Transmission Rod 06 x 1 02 Right Desk Leg 03 x 1 Bolt M6 x 35mm B x8 Bolt M6 x 11mm A x4 Large Allen Wrench 3/16 (5mm) C x1 Small Allen Wrench 5/64 (2mm) D x1 Supplied Parts and Hardware for Step 3 Desktop 07 x 1 Controller 08 x 1 Rubber Pad E x 10 Screw M5 x 16mm F x 16 Wood Dowel Pin G x4 Storage Hook H x2 Supplied Parts and Hardware for Step 4 AC Adapter 09 x 1 Cable Clip I x2 Supplied Parts and Hardware for Step 5 Cable Hole Cover J x2 03 Step 1: Assembling and Connecting the Desk Legs C Large Allen Wrench A 03 03 02 01 04 C Large 04 Allen Wrench B 04 04 Step 2: Attaching the Side Plates and the Transmission Rod 05 05 A 05 C Large Allen Wrench Loosen the coupling nut. Coupling nut 06 05 Fig 1 a Turn b anti-clockwise Left Leg 06 Fig 2 a Turn b clockwise Left Leg Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the left leg. Turn the rod to adjust the left leg so it's level with the right leg. Turn the rod clockwise to lower the left leg or anti-clockwise to raise it. Note: Make sure the set screw faces out. Right Leg Ensure the transmission rod is properly inserted into the hole in the left leg. Smoothly connect the other end of the rod to the end of the motor drive shaft on the right leg. 06 D Small Allen Wrench Secure the transmission rod to the motor drive shaft by turning the set screw clockwise. E Tighten the coupling nut to fine-tune transmission rod fit. 07 Step 3: Assembling and Attaching the Desktop Assemble the desktop. 07 G 07 07 07 08 Attach the desktop to the frame. (not Drill included) OR Phillips Screwdriver (not included) You can use a drill (with suitable torque and speed) or a Phillips screwdriver. OR F Attach the controller and hooks to the desktop. OR F H OR F 08 09 Step 4: Connecting the Cables 09 I 08 08 099 Step 5: Installing the Cable Hole Covers J 10 Using the Controller Save Current Height Setting Short-press the S button, and the display will flash. Press the 1 , 2 , or 3 button to save the current height setting to that button. Select Height Setting 1 Press the 1 button, and the desk will move to the height that was previously set for that button. Select Height Setting 2 Press the 2 button, and the desk will move to the height that was previously set for that button. Select Height Setting 3 Press the 3 button, and the desk will move to the height that was previously set for that button. Raise the Desk Press the button to raise the desk continuously until it reaches the highest position of 46.5 (118cm) or the button is released. Lower the Desk Press the button to lower the desk continuously until it reaches the lowest position of 28.3 (72cm) or the button is released. Settings Change Display Height Units Press and hold the S button until a flashing `S-' is displayed. Press S again, and `Un' is displayed. Press S to select it, press or to switch between `IN' (imperial) and `SI' (metric), and press S to save your choice. Change Collision Detection Sensitivity Long press the S button, `S-' shows and flashes. Press S again and the display shows `Un.' Press or to switch to `CF.' Press S to select. Press or to switch between `OFF,' Low (L), Normal (n) or Heavy (H) collision force detection. Press S to save your choice. Reset Press and hold the button for 5 seconds, and the screen will show `RES.' Continue holding until the desk goes down to its lowest level and comes back up slightly. 11 Protection Mode Error Codes Overheating Protection: When the motor has been working Hot continuously for 2 minutes, it will stop operating to prevent damage from overheating. Wait for at least 18 minutes before making any further height adjustment. E10 Sensor Malfunction Warning: Motor safety sensor can't be detected. Power off, check the connection between the motor and controller, and power back on again. E20 Overloading Warning: Max load exceeded. If raising the desk, take the things off the desk and try again. If lowering the desk, power off, take the things off the desk, power back on, and try again. If error code persists, follow the reset instructions. E02 Operation Status Warning: The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use. E32 Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again. E31 Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again. E60 Unequal Leg Height Warning: Power off the desk and check whether the left and right legs are at the same height. Adjust if necessary by following the instructions. Power on again. Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected. 860-00950-00 Rev00 12Adobe Illustrator 25.0 (Windows) iLovePDF