Office Desk Assembly Manual

Assembly Instructions

IMPORTANT INSTALLATION TIP: Align and loosely thread all bolts into the corresponding holes before fully tightening each bolt one by one. This allows for minor adjustments during assembly.

NOTE: Please note the distinction between the bottom and top of mesh shelves. The bottom has a recessed mesh, while the top has a flat surface.

STEP 1: Attach the Feet

1. Take two Desk Legs [9], one Desk Short Leg [10], one Desk Leg [11], one Side Table Left Leg [14], and one Side Table Right Leg [15].
2. Attach 12 Foot M6 [H] pieces to the bottom of these legs. Each leg receives two feet. Ensure they are securely threaded.

STEP 2: Assemble the Side Table

1. Attach the Side Table Mesh Panel [16] to the Side Table Left Leg [14] and Side Table Right Leg [15] using 4 Bolt M6 x 28mm [A] and the Allen Key [K]. Ensure the support bars on desk legs [14] and [15] face inward with the lip toward the back.
2. Place the Side Table Panel [5] on top of the assembled side table frame. Secure it using 4 Bolt M6 x 28mm [A] and the Allen Key [K].
3. Assemble the drawer. Attach the Drawer Bottom [29b] to the Drawer [29a]. Secure the Drawer Handle [J] to the drawer using 2 Bolt M4 x 10mm [E] and the Phillips Screwdriver [M]. Slide the assembled drawer into the side table.

STEP 3: Connect the Desk Legs

1. Connect the Desk Legs [9] and [11] using the Middle Long Tube [18], Top Front Tube [19], and Top Rear Tube [20]. Use 6 Bolt M6 x 28mm [A] and the Allen Key [K]. Ensure the holes for future connections are correctly oriented as shown in the diagram.
2. Attach the Bottom Short Tube [24] to the Desk Leg [9] and Desk Short Leg [10] using 4 Bolt M6 x 28mm [A] and the Allen Key [K].
3. Attach the Desk Mesh Panel [17] to the Desk Short Leg [10] and Desk Leg [11] using 8 Bolt M6 x 28mm [A] and the Allen Key [K].

STEP 4: Connect Two Sections of Desk Frame

There are two installation options for the desk frame:

Option A (Follow page 10 layout):

1. Connect the two main desk frame sections using Top Front Tube [21], Top Rear Tube [22], and Middle Short Tube [23]. Use 8 Bolt M6 x 28mm [A], 1 Nut M6 [G], 1 Allen Key [K], and 1 Wrench [L].
2. NOTE: Large holes on the tubes should face up. Fully tighten these two bolts [A] before attaching the desktop.
3. Aligning the holes can be tricky. It is recommended to tighten a few screws before attempting to align them all.
4. Place the Desktop [1] and Desktop [2] panels upside down on a soft, level surface (like a carpet or blanket) to prevent scratches.
5. Attach the assembled desk frame to the underside of the Desktop [1] and Desktop [2] using 9 Bolt M6 x 28mm [A] and the Allen Key [K]. This step may require two people.

Option B (Follow page 11 layout):

1. Connect the two main desk frame sections using Top Front Tube [21], Top Rear Tube [22], and Middle Short Tube [23]. Use 8 Bolt M6 x 28mm [A], 1 Nut M6 [G], 1 Allen Key [K], and 1 Wrench [L].
2. NOTE: Large holes on the tubes should face up. Fully tighten these two bolts [A] before attaching the desktop.
3. Aligning the holes can be tricky. It is recommended to tighten a few screws before attempting to align them all.
4. Place the Desktop [1] and Desktop [2] panels upside down on a soft, level surface (like a carpet or blanket) to prevent scratches.
5. Attach the assembled desk frame to the underside of the Desktop [1] and Desktop [2] using 9 Bolt M6 x 28mm [A] and the Allen Key [K]. This step may require two people.

The installation process from this point forward is the same for either Option A or Option B.

STEP 5: Attach the Stand

1. Attach the two Stand Side Frames [13] to the desk frame using 4 Bolt M6 x 28mm [A] and the Allen Key [K].
2. Attach the Stand Panel [3] and Stand Support [26] to the stand frame using 2 Bolt M6 x 28mm [A] and the Allen Key [K].
3. Secure the Stand Panel [3] to the desk frame using 2 Bolt M6 x 28mm [A] and the Allen Key [K].

STEP 6: Attach the Top Shelf

1. Attach the two Top Shelf Side Frames [12] to the desk frame using 4 Bolt M6 x 60mm [C], 4 Nut M6 [G], 1 Allen Key [K], and 1 Wrench [L].
2. Attach the two Top Shelf Supports [25] to the desk frame using 4 Bolt M6 x 28mm [A] and the Allen Key [K].
3. Assemble the top shelf unit. Connect the Top Shelf Upper Panel [6], Top Shelf Lower Panel [7], and three Top Shelf Vertical Panels [8] using 12 Bolt M7 x 40mm [D] and the Allen Key [K].
4. Place the assembled top shelf unit onto the desk frame, aligning it with the Top Shelf Side Frames [12] and Top Shelf Supports [25].

STEP 7: Attach the Support Bars on the Back

1. Attach the four Support Bars [27] to the back of the desk frame. Use 4 Bolt M6 x 28mm [A], 2 Bolt M6 x 35mm [B], 6 Nut M6 [G], 1 Allen Key [K], and 1 Wrench [L]. Ensure all connections are secure.

STEP 8: Attach the Power Outlet and Light Strip

1. Attach the Power Outlet [28] to the designated area on the desk using 2 Screw M4 x 12mm [F] and the Phillips Screwdriver [M].
2. Attach the Light Strip [30] to the underside of the top shelf or desk edge as desired.

Remember to fully tighten all bolts, screws, and nuts after completing all assembly steps.