Safety First: Preventing Tip-Over
WARNING! Serious or fatal crushing injuries can occur from furniture tip-over. To prevent tip-over, this furniture must be used with the wall attachment device(s) provided.
Screw(s) and plug(s) for the wall are not included. Use screw(s) and plug(s) suitable for your walls. If you are uncertain, seek professional advice. Read and follow each step of the instructions carefully.
Warnings are also provided in Spanish, Portuguese, Japanese, Indonesian, Malay, Arabic, Thai, and Korean.
Tools Required
- Screwdriver ?
- Pencil ✏️
- Hammer ?
- Spirit level ?
Parts List
| Quantity | Description | Part Identifier |
|---|---|---|
| 8x | Screw | 104322 |
| 16x | Dowel | 101339 |
| 12x | Dowel | 101345 |
| 4x | Screw | 100372 |
| 1x | Allen key | 100092 |
| 1x | Wall attachment bracket | 121030 |
| 2x | Corner bracket/connector | 115753 |
| 2x | Wall bracket plate | 103693 |
| 8x | Foot/cap | 153550 |
| 2x | Corner piece | 118225 |
Assembly Instructions
Unit Assembly
- Step 1: Attach the wall attachment bracket (121030) to the wall using screws (104322) and the Allen key (100092).
- Step 2: Insert dowels (101339) into the pre-drilled holes on the side panels. Gently tap with a hammer ? if needed.
- Step 3: Connect a side panel to the base or top panel using the inserted dowels (101345).
- Step 4: Insert dowels (101339) into the pre-drilled holes on the internal dividers.
- Step 5: Insert dowels (101345) into the pre-drilled holes on the shelves.
- Step 6: Attach the internal dividers to the base/top panel using the dowels (101339).
- Step 7: Attach the second side panel to the structure using dowels (101339).
- Step 8: Insert dowels (101339) into the remaining internal dividers.
- Step 9: Attach the remaining internal dividers to the structure using dowels (101345).
- Step 10: Attach the top or base panel to the assembled structure using dowels (101339).
- Step 11: Lay the unit down. Attach the back panel using screws (104322) and the Allen key (100092).
- Step 12: Attach the final side panel to the unit using screws (104332) and the Allen key (100092).
- Step 13: Attach the feet/caps (153550) to the bottom of the unit. Press them firmly into place.
Wall Mounting (Vertical Configuration)
- Step 14: Prepare for wall mounting. Attach the bracket plates (115753) to the top of the unit using screws (100372). Ensure the orientation is correct as shown.
- Step 15: Use a spirit level ? to ensure the unit is upright. Attach the corresponding wall brackets to the wall at the appropriate height, using suitable wall fixings (not included). Follow the markings on the wall bracket plates.
- Step 16: Insert screws into the wall brackets to secure them.
- Step 17: Align the unit with the wall brackets and secure it. The diagram shows the unit being slid onto the wall brackets and then secured with a locking mechanism.
Wall Mounting (Horizontal Configuration)
- Step 14: Attach the feet/caps (153550) to the bottom of the unit. Press them firmly into place.
- Step 15: Attach the bracket plates (115753) to the unit using screws (100372). Ensure the orientation is correct as shown.
- Step 16: Use a spirit level ? to ensure the unit is level. Attach the corresponding wall brackets to the wall at the appropriate height, using suitable wall fixings (not included). Follow the markings on the wall bracket plates.
- Step 17: Insert screws into the wall brackets to secure them.
- Step 18: Align the unit with the wall brackets and secure it. The diagram shows the unit being slid onto the wall brackets and then secured with a locking mechanism.
