Philips Shaver S3144/00 User Manual

Important Safety Information

Only use the product for its intended purpose. Read this important information carefully before you use the product and its batteries and accessories, and save it for future reference. Misuse can lead to hazards or serious injuries. Accessories supplied may vary for different products.

Warning

• To charge the product, only use a certified safety extra low voltage (SELV) supply unit with output rating 5 V, ≥ 1 A.
• For safe charging in a moist environment (e.g. in a bathroom), only use an IPX4 (splash-proof) supply unit.
• A suitable supply unit (e.g. Philips HQ87) is available via www.philips.com/support.
• If you need support finding the correct USB supply unit, contact the Consumer Care Center in your country (see the international warranty leaflet for contact details). Using a non-certified supply unit may cause hazards or serious injuries.
• Keep the USB cable, the USB supply unit and the charging stand dry (Figure 1).
• This shaver is waterproof (Figure 2). It is suitable for use in the bath or shower and for cleaning under the tap. For safety reasons, the shaver can therefore only be used without cord.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Do not modify the supply unit.
• Do not use the supply unit in or near wall sockets that contain an electric air freshener to prevent irreparable damage to the supply unit.
• Do not use a damaged appliance. Replace damaged parts with new Philips parts.
• Because of hygiene, only one person should use the appliance.
• Unplug the appliance before cleaning it with water.
• Only use cold or lukewarm water to clean the appliance.
• Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids to clean the appliance.
• Water may drip from the socket at the bottom of the shaver when you rinse it. This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the shaver.

Product Use and Care

• Only use original Philips accessories or consumables.
• Charge, use and store the product at a temperature between 10 °C and 35 °C.
• Keep product and batteries away from fire and do not expose them to direct sunlight or high temperatures.
• If the product becomes abnormally hot or smelly, changes color or if charging takes longer than usual, stop using and charging the product and contact Philips.
• Do not place products and their batteries in microwave ovens or on induction cookers.
• Do not open, modify, pierce, damage or dismantle the product or battery to prevent batteries from heating up or releasing toxic or hazardous substances. Do not short-circuit, overcharge or reverse charge batteries.
• If batteries are damaged or leaking, avoid contact with the skin or eyes. If this occurs, immediately rinse well with water and seek medical care.

Electromagnetic Fields (EMF)

This Philips appliance complies with all applicable standards and regulations regarding exposure to electromagnetic fields.

Support

For all product support such as frequently asked questions, please visit www.philips.com/support.

Recycling

This symbol (Figure 3) means that electrical products and batteries shall not be disposed of with normal household waste.

Follow your country's rules for the separate collection of electrical products and batteries.

Removal of Built-in Rechargeable Battery

The built-in rechargeable battery must only be removed by a qualified professional when the appliance is discarded. Before removing the battery, make sure that the appliance is disconnected from the wall socket and that the battery is completely empty.

Take any necessary safety precautions when you handle tools to open the appliance and when you dispose of the rechargeable battery.

When you handle batteries, make sure that your hands, the product and the batteries are dry.

To avoid accidental short-circuiting of batteries after removal, do not let battery terminals come into contact with metal objects (e.g. coins, hairpins, rings). Do not wrap batteries in aluminum foil. Tape battery terminals or put batteries in a plastic bag before you discard them.

Steps for Battery Removal:

1. Check if there are screws in the back or front of the appliance. If so, remove them.
2. Remove the back and/or front panel of the appliance with a screwdriver. If necessary, also remove additional screws and/or parts until you see the printed circuit board with the rechargeable battery.
3. Remove the rechargeable battery.

Product Usage and Maintenance

Charging the Shaver

Follow these steps for charging:

1. Connect the USB cable to the supply unit and the charging stand.
2. Place the shaver on the charging stand.
3. Ensure the shaver is fully charged before first use. A full charge takes approximately 60 minutes.
4. A quick charge of 5 minutes provides enough power for one shave.

Shaving

The shaver is waterproof and suitable for use in the bath or shower and for cleaning under the tap. For safety reasons, the shaver can only be used without a cord.

1. For a wet shave, use shaving foam or gel (optional).
2. Shave against the direction of hair growth.
3. Rinse the shaver head under running water after use.

Cleaning the Shaver

The shaver can be cleaned under running water.

1. Rinse the shaver head under running water.
2. Open the shaving head by pressing the release button.
3. Rinse the shaving heads and the inner cap thoroughly.
4. Dry the shaver head and allow it to air dry completely before reassembling.
5. For a deeper clean, the shaving heads (e.g., SH30) can be removed.

Replacing Shaving Heads

Shaving heads (e.g., SH30) should be replaced approximately every 24 months (24M) for optimal performance.

1. Open the shaving head.
2. Remove the old shaving heads.
3. Insert the new shaving heads.
4. Close the shaving head.