Chauvet AmHaze ECO User Manual
Introduction
The AmHaze ECO is a professional water-based haze machine that delivers high output while utilizing economic fluid consumption. With a 30-second heat-up time and continuous output that doesn't require reheating, a single fluid container at the maximum output of 120 cfm will last over 8 hours. Easily control the output and fan speed via DMX or on the on-board control knobs. The AmHaze ECO comes ready to rest on the floor and is also equipped with M12 threaded inserts for truss clamps, an easy way to mount the 25 lb machine. The AmHaze ECO combines high output with efficient operation for a complete atmosphere solution for medium to large venues.
Features
- Professional water-based haze machine
- 30-sec heat-up time nearly eliminates wait time for operation
- Continuous output with no reheating required
- Tour-ready with M12 threaded insert for truss clamps
- Efficient fluid consumption lasts more than 8 hours on a single fluid container
- Achieve continuous variable haze output and blower speed, adjusted via DMX or manual knobs
Product Overview
Diagram showing the AmHaze ECO with labels pointing to: Output nozzle, Safety loop, Fluid reservoir, Blower fan, DMX in/out, LCD display, Menu buttons, Manual knobs, Breaker reset button, Power in.
Product Dimensions
Diagram showing the AmHaze ECO from different angles with dimensions: Length 15.86 in (403 mm), Width 12.20 in (310 mm), Height 10.07 in (256 mm).
Setup
AC Power
The AmHaze ECO has a fixed power supply that works with an input voltage of either 120 VAC, 60 Hz or 230 VAC, 50 Hz, depending on the specific model. To determine the product's power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product's back panel, or refer to the product's specifications chart. The listed current rating indicates the product's average current draw under normal conditions.
Important Safety Note: ⚠️ Always connect the product to a protected circuit (a circuit breaker or fuse). Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire.
ℹ️ To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel serves only as a 0 to 100% switch.
AC Plug
The AmHaze ECO comes with a power input cord terminated with a Seetronic Powerkon A connector on one end and an Edison plug on the other end (U.S. market). If the power input cord that came with the product has no plug, or if the user needs to change the plug, use the table below to wire the new plug.
| Connection | Wire (U.S.) | Wire (Europe) | Screw Color |
|---|---|---|---|
| AC Live | Black | Brown | Yellow or Brass |
| AC Neutral | White | Blue | Silver |
| AC Ground | Green/Yellow | Green/Yellow | Green |
Resetting the Breaker
This product is equipped with a resettable circuit breaker. If the breaker trips, all sections of this product will lose power.
- Remove the power cord from main power.
- Allow unit to cool for 15 minutes.
- After 15 minutes, user may attempt to reset the breaker by pressing the button with their finger.
- Plug the product's power cord into the power outlet and continue using as recommended.
DMX Linking
The AmHaze ECO can link to a DMX controller using a 3-pin or 5-pin DMX connection. If using other DMX-compatible products with this product, user can control each individually with a single DMX controller.
DMX Personalities
The AmHaze ECO uses a 3-pin or 5-pin DMX data connection for the 3-channel DMX personality. For more information about DMX standards, Master/Slave connectivity, or the DMX cables needed to link this product to a DMX controller, download the DMX Primer from the Chauvet website: www.chauvetprofessional.com.
Remote Device Management (RDM)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate bi-directionally along existing DMX cabling. Check the DMX controller's User Manual or with the manufacturer as not all DMX controllers have this capability. The AmHaze ECO supports RDM protocol that allows feedback to make changes to menu map options.
Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. For Chauvet Professional line of mounting clamps, go to http://trusst.com/products/.
Orientation
Always mount this product in a safe position, making sure there is adequate room for ventilation, configuration, and maintenance.
Rigging
Chauvet recommends using the following general guidelines when mounting this product.
- Before deciding on a location, always make sure there is easy access to the product for maintenance and programming.
- Mount the product on a structure or surface that can support the product's weight. See the Technical Specifications for weight information.
- Always use a safety cable when mounting the product overhead.
- Use a mounting clamp of appropriate weight capacity when rigging the product onto truss.
Procedure
The AmHaze ECO comes with a bracket to which users can directly attach mounting clamps. Mounting clamps are sold separately. Make sure the clamps are capable of supporting the weight of this product. Use at least two mounting points per product. For the Chauvet Professional line of mounting clamps, go to http://www.trusst.com/products.
Diagram illustrating how to mount the AmHaze ECO. It shows an M12 threaded mounting hole on the unit, a mounting clamp attached to it, and a safety cable connected to the unit and the mounting structure.
Operation
Control Panel Description
| Button | Function |
|---|---|
| <MENU> | Exits from the current menu or function |
| <UP/TIMER> | UP navigates upwards through the menu list and increases the numeric value when in a function. TIMER starts the timer controlled operation. |
| <DOWN/VOLUME> | DOWN navigates downwards through the menu list and decreases the numeric value when in a function. VOLUME triggers the pump to modify the output volume. |
| <ENTER/STOP> | ENTER enables the currently displayed menu or sets the currently selected value into the selected function. STOP turns the fog output off. |
| HAZE FAN knob | Manually controls the fan speed, 0–100% |
| HAZE VOLUME knob | Manually controls the haze volume, 0–100% |
Control Options
Set the AmHaze ECO starting address in the 001–510 DMX range. This enables control of up to 170 products.
Programming
Refer to the Menu Map to understand the menu options. The menu map shows the main level and a variable number of programming levels for each option.
- To go to the desired main level, press <MENU> repeatedly until the option shows on the display.
- Press <ENTER> to select. The first programming level for that option will show on the display.
- To select an option or value within the current programming level, press <UP> or <DOWN> until the option shows on the display. Press <ENTER> to select. The selected value or the first option of the next programming level will show on the display.
- Press <MENU> repeatedly to exit to the previous main level.
Menu Map
Refer to the AmHaze ECO product page on www.chauvetprofessional.com for the latest menu map.
| Main Level | Programming Levels | Description |
|---|---|---|
| Haze Output | 1-100% | Haze volume 1-100% |
| Fan Speed | 1-100% | Fan speed (slow to fast) |
| Timer Interval | 5-600S | Sets the interval of haze outputs |
| Timer Duration | 5-300S | Sets the duration of the haze output |
| DMX Address | 1-512 | Selects the DMX starting address |
| RDM-UID | --- | Unique identification number |
| Fluid Sensor | ON OFF | Turns the fluid sensor ON or OFF |
| Auto Run Last Setting | YES NO | Automatically set the values to previous selections |
| Self-Clean & Shutdown | YES NO | Self-clean mode will begin counting down from 180 seconds to 4 seconds, then shut down after 3 seconds |
| Auto Shutdown | ON OFF | Turns off all functions |
RDM Chart
Refer to the AmHaze ECO product page on www.chauvetprofessional.com for the latest RDM chart.
| Category | RDM Parameter ID's (Slots 21-22) | Value | Required | GET Allowed | SET Allowed | Chauvet | Detail |
|---|---|---|---|---|---|---|---|
| Network Management | DISC_UNIQUE_BRANCH | 0x0001 | ☑ | ||||
| DISC_MUTE | 0x0002 | ☑ | |||||
| DISC_UN_MUTE | 0x0003 | ☑ | |||||
| Status Collection | PROXIED_DEVICES | 0x0010 | ☑ | ||||
| PROXIED_DEVICE_COUNT | 0x0011 | ☑ | |||||
| RDM Information | COMMS_STATUS | 0x0015 | ☑ | ||||
| QUEUED_MESSAGE | 0x0020 | ☑ | |||||
| STATUS_MESSAGES | 0x0030 | ☑ | Fluid level Low, Fail to Heat | ||||
| STATUS_ID_DESCRIPTION | 0x0031 | ☑ | Temperature | ||||
| CLEAR_STATUS_ID | 0x0032 | ☑ | |||||
| SUB_DEVICE_STATUS_REPORT_THRESHOLD | 0x0033 | ☑ | |||||
| RDM Information | SUPPORTED_PARAMETERS | 0x0050 | ☑ | ||||
| PARAMETER_DESCRIPTION | 0x0051 | ☑ | |||||
| DEVICE_INFO | 0x0060 | ☑ | |||||
| PRODUCT_DETAIL_ID_LIST | 0x0070 | ☑ | |||||
| Product Information | DEVICE_MODEL_DESCRIPTION | 0x0080 | ☑ | Amhaze ECO | |||
| MANUFACTURER_LABEL | 0x0081 | ☑ | Chauvet Professional | ||||
| DEVICE_LABEL | 0x0082 | ☑ | Amhaze ECO | ||||
| FACTORY_DEFAULTS | 0x0090 | ☑ | |||||
| LANGUAGE_CAPABILITIES | 0x00A0 | ☑ | |||||
| LANGUAGE | 0x00B0 | ☑ | |||||
| SOFTWARE_VERSION_LABEL | 0x00C0 | ☑ | |||||
| BOOT_SOFTWARE_VERSION_ID | 0x00C1 | ☑ | |||||
| BOOT_SOFTWARE_VERSION_LABEL | 0x00C2 | ☑ | |||||
| DMX512 Setup | DMX_PERSONALITY | 0x00E0 | ☑ | ||||
| DMX_PERSONALITY_DESCRIPTION | 0x00E1 | ☑ | |||||
| DMX_START_ADDRESS | 0x00F0 | ☑ | |||||
| SLOT_INFO | 0x0120 | ☑ | |||||
| SLOT_DESCRIPTION | 0x0121 | ☑ | |||||
| Sensors | DEFAULT_SLOT_VALUE | 0x0122 | ☑ | ||||
| DMX_BLOCK_ADDRESS | 0x0140 | ☑ | |||||
| DMX_FAIL_MODE | 0x0141 | ☑ | Retain last DMX values | ||||
| DMX_STARTUP_MODE | 0x0142 | ☑ | Reset all values to DMX-000 | ||||
| SENSOR_DEFINITION | 0x0200 | ☑ | No function Prime pump | ||||
| SENSOR_VALUE | 0x0201 | ☑ | Min Value(C) Max Value (C) | ||||
| RECORD_SENSORS | 0x0202 | ☑ | Display sensor value in C |
| Category | RDM Parameter ID's (Slots 21-22) | Value | Required | GET Allowed | SET Allowed | Chauvet | Detail | |
|---|---|---|---|---|---|---|---|---|
| Dimmer Settings | DIMMER_INFO | 0x0340 | ☑ | |||||
| MINIMUM_LEVEL | 0x0341 | ☑ | ||||||
| MAXIMUM_LEVEL | 0x0342 | ☑ | ||||||
| CURVE | 0x0343 | ☑ | ||||||
| CURVE_DESCRIPTION | 0x0344 | ☑ | ||||||
| OUTPUT_RESPONSE_TIME | 0x0345 | ☑ | ||||||
| OUTPUT_RESPONSE_TIME_DESCRIPTION | 0x0346 | ☑ | ||||||
| MODULATION_FREQUENCY | 0x0347 | ☑ | ||||||
| MODULATION_FREQUENCY_DESCRIPTION | 0x0348 | ☑ | ||||||
| Power Settings | DEVICE_HOURS | 0x0400 | ☑ | Total Runtime for life of product | ||||
| LAMP_HOURS | 0x0401 | ☑ | Shows the runtime since last cleaning cycle was performed | |||||
| LAMP_STRIKES | 0x0402 | ☑ | Resets once cleaning cycle has been performed | |||||
| LAMP_STATE | 0x0403 | ☑ | ||||||
| LAMP_ON_MODE | 0x0404 | ☑ | ||||||
| DEVICE_POWER_CYCLES | 0x0405 | ☑ | ||||||
| BURN_IN | 0x0440 | ☑ | ||||||
| Display Settings | DISPLAY_INVERT | 0x0500 | ☑ | ☑ | Normal/Inverted 180 | |||
| DISPLAY_LEVEL | 0x0501 | ☑ | ||||||
| PAN_INVERT | 0x0600 | ☑ | ||||||
| TILT_INVERT | 0x0601 | ☑ | ||||||
| PAN_TILT_SWAP | 0x0602 | ☑ | ||||||
| Configuration | REAL_TIME_CLOCK | 0x0603 | ☑ | |||||
| LOCK_PIN | 0x0640 | ☑ | ||||||
| LOCK_STATE | 0x0641 | ☑ | ||||||
| LOCK_STATE_DESCRIPTION | 0x0642 | ☑ |
| Category | RDM Parameter ID's (Slots 21-22) | Value | Required | GET Allowed | SET Allowed | Chauvet | Detail | |
|---|---|---|---|---|---|---|---|---|
| Network Configuration | LIST_INTERFACES | 0x0700 | ☑ | |||||
| INTERFACE_LABEL | 0x0701 | ☑ | ||||||
| INTERFACE_HARDWARE_ADDRESS_TYPE1 | 0x0702 | ☑ | ||||||
| IPV4_DHCP_MODE | 0x0703 | ☑ | ||||||
| IPV4_ZEROCONF_MODE | 0x0704 | ☑ | ||||||
| IPV4_CURRENT_ADDRESS | 0x0705 | ☑ | ||||||
| IPV4_STATIC_ADDRESS | 0x0706 | ☑ | ||||||
| INTERFACE_RENEW_DHCP | 0x0707 | ☑ | ||||||
| INTERFACE_RELEASE_DHCP | 0x0708 | ☑ | ||||||
| INTERFACE_APPLY_CONFIGURATION | 0x0709 | ☑ | ||||||
| IPV4_DEFAULT_ROUTE | 0x070A | ☑ | ||||||
| DNS_IPV4_NAME_SERVER | 0x070B | ☑ | ||||||
| DNS_IPV4_DOMAINNAME | 0x070C | ☑ | ||||||
| DNS_DOMAIN_NAME | 0x070D | ☑ | ||||||
| Control | IDENTIFY_DEVICE | 0x1000 | ☑ | ☑ | Yes/No | |||
| RESET_DEVICE | 0x1001 | ☑ | ||||||
| POWER_STATE | 0x1010 | ☑ | ||||||
| PERFORM_SELFTEST | 0x1020 | ☑ | ☑ | Primes Unit | ||||
| SELF_TEST_DESCRIPTION | 0x1021 | ☑ | ☑ | Primes Unit | ||||
| CAPTURE_PRESET | 0x1030 | ☑ | ||||||
| PRESET_PLAYBACK | 0x1031 | ☑ | ||||||
| IDENTIFY_MODE | 0x1040 | ☑ | ||||||
| PRESET_INFO | 0x1041 | ☑ | ||||||
| PRESET_STATUS | 0x1042 | ☑ | ||||||
| PRESET_MERGEMODE | 0x1043 | ☑ | ||||||
| POWER_ON_SELF_TEST | 0x1044 | ☑ |
Configuration (DMX)
Use control configurations to operate the product with a DMX controller.
Starting Address
Each product will respond to a unique starting address from the controller. All products with the same starting address will respond in unison. To set the starting address:
- Go to the DMX Address main level.
- Select the starting address (1–512). The highest recommended starting address is 510.
Control Channel Assignments and Values
3-Channel
| Channel | Function | Value | Percent/Setting |
|---|---|---|---|
| 1 | Fan speed | 000 ⇨ 010 011 ⇨ 255 | No function 1-100% |
| 2 | Haze output | 000 ⇨ 010 011 ⇨ 255 | No function 1-100% |
| 3 | Remote clean function | 000 ⇨ 151 152 ⇨ 159 160 ⇨ 255 | No function Remote clean function Standby mode |
Configuration (Standalone)
Haze Output
To adjust the haze output through the display menu:
- Go to the Haze Output level.
- Increase or decrease the value from 1-100%.
Fan Speed
To adjust the fan speed through the display menu:
- Go to the Fan Speed level.
- Increase or decrease the value from 1-100%.
Timer Interval
To adjust the interval of timed haze outputs through the display menu:
- Go to the Timer Interval level.
- Increase or decrease the value from 5-600S.
Timer Duration
To adjust the duration of timed haze outputs through the display menu:
- Go to the Timer Duration level.
- Increase or decrease the value from 5-300S.
Configuration (Settings)
RDM-UID
To view the RDM-UID of the product, go to the RDM-UID level.
Fluid Sensor
To enable or disable the fluid sensor function:
- Go to the Fluid Sensor level.
- Select from ON or OFF.
Auto Run Last Setting
To set the control values to the last ones used:
- Go to the Auto Run Last Setting level.
- Select from YES or NO.
Auto Shutdown
To shut all functions down:
- Go to the Auto Shutdown level.
- Select from ON or OFF.
Priming the Pump
The AmHaze ECO features an automatic shut-off function. When the fluid sensor detects no fluid in the hose, the pump automatically shuts off. Sometimes an air bubble can be caught in the hose by the fluid sensor, triggering the auto shut-off. To prevent this, the pump must be primed every time the reservoir is refilled from empty and/or every time the hose runs dry.
To prime the pump and remove all air bubbles:
- Ensure the filter tip of the hose is fully submerged in the fluid.
- Run the AmHaze ECO on low haze volume.
- With two fingers, pinch the hose closed so nothing can pass through. DO NOT use fingernails or anything which may cut the hose!
- Keep the hose pinched closed for 20–30 seconds. The pump will make a noise that will slowly get louder.
- After at least 20–30 seconds, release the hose. Fluid should pass quickly through it, preventing any bubbles from becoming trapped.
The pump must be primed every time the reservoir is refilled, or the hose runs dry.
Maintenance
Product Maintenance
Do not allow the haze machine to become clogged. After every 40 hours of continuous operation, use Chauvet Fog Cleaner Quart (FCQ) through the system to prevent the accumulation of particulate matter in the heating element.
The recommended cleaning procedure is as follows:
- Unplug the product from power.
- Empty all fluid from the machine.
- Add cleaning solution to the tank.
- Connect the product to power and allow it to warm up.
- Run the unit in a well-ventilated area until the tank is empty.
- Refill with fluid to continue using the hazer. Run the machine briefly to clear any cleaning solution from the pump and heater.
ℹ️ FCQ was specifically developed by Chauvet to clean the AmHaze ECO. Make sure to use FCQ regularly to increase the life of the hazer.
ℹ️ Do not spin the fans using compressed air because it could damage the hazer. Test-run the AmHaze ECO on a monthly basis to achieve the best performance.
⚠️ Never operate the machine without fluid.
Storage
Before storing the product, empty the fluid reservoirs. Cleaning the system prior to storage will help prevent any particles from condensing inside the heating element while not in use.
Technical Specifications
Dimensions and Weight
| Length | Width | Height | Weight | |
|---|---|---|---|---|
| 15.86 in (403 mm) | 12.20 in (310 mm) | 10.07 in (256 mm) | 25 lb (11.4 kg) | |
| Note: Dimensions in inches are rounded. | ||||
Power
| Parameter | Range | Voltage Selection |
|---|---|---|
| Power Supply Type | Fixed | Fixed |
| Consumption | 120 V, 60 Hz 1,230 W | 230 V, 50 Hz 2,430 W |
| Operating Current | 10.25 A | 10.56 A |
| Power I/O | U.S./Worldwide | UK/Europe |
| Power Input Connector | Seetronic Powerkon IP65 Edison (U.S.) | Seetronic Powerkon IP65 Local Plug |
Operation
| Tank Capacity | Fluid Consumption | Fan Speed | Maximum Run-Time | |
|---|---|---|---|---|
| 0.92 gal (3.5 L) | 0.11 gallons/hour (7 ml/min) | 120 cfm | 8 hours @ full volume |
Thermal
| Startup Temperature Range | Operating Temperature Range | Cooling System | |
|---|---|---|---|
| 50 °F to 113 °F (10 °C to 45 °C) | 50 °F to 113 °F (10 °C to 45 °C) | Convection |
DMX
| I/O Connector | Channel Range | |
|---|---|---|
| 3-pin and 5-pin XLR | 3 |
Ordering
| Product Name | Item Name | Item Code | UPC Number |
|---|---|---|---|
| AmHaze ECO (120V) | AMHAZEECO | 09071502 | 781462218508 |
| AmHaze ECO (230V) | 220AMHAZEECO | 09071503 | 781462218515 |
Certifications: MET, UL 499, CSA C22.2 No. 64-10, E115095, FCC, CE, RoHS.
Contact Us
General Information
Chauvet World Headquarters
Address: 3360 Davie Rd.
Davie, FL 33314
Voice: (954) 577-4455
Fax: (954) 929-5560
Toll Free: (800) 762-1084
Technical Support
Voice: (844) 393-7575
Fax: (954) 756-8015
Email: chauvetcs@chauvetlighting.com
Website: www.chauvetprofessional.com
Chauvet U.K.
Address: Pod 1 EVO Park
Little Oak Drive, Sherwood Park
Nottinghamshire, NG15 0EB
UK
Voice: +44 (0) 1773 511115
Fax: +44 (0) 1773 511110
Email: UKtech@chauvetlighting.eu
Website: www.chauvetprofessional.eu
Chauvet Benelux
Address: Stokstraat 18
9770 Kruishoutem
Belgium
Voice: +32 9 388 93 97
Email: BNLtech@chauvetlighting.eu
Website: www.chauvetprofessional.eu
Chauvet France
Address: 3, Rue Ampère
91380 Chilly-Mazarin
France
Voice: +33 1 78 85 33 59
Email: FRtech@chauvetlighting.fr
Website: www.chauvetprofessional.eu
Chauvet Germany
Address: Bruno-Bürgel-Str. 11
28759 Bremen
Germany
Voice: +49 421 62 60 20
Email: DEtech@chauvetlighting.de
Website: www.chauvetprofessional.eu
Chauvet Mexico
Address: Av. de las Partidas 34 - 3B
(Entrance by Calle 2)
Zona Industrial Lerma
Lerma, Edo. de México, CP 52000
Voice: +52 (728) 690-2010
Email: servicio@chauvet.com.mx
Website: www.chauvetprofessional.mx
Warranty & Returns
For warranty terms and conditions and return information, please visit our website.
For customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration.
For customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and Germany: www.chauvetlighting.eu/warranty-registration.
