VTech VM5467 5" Pan & Tilt Monitor

Technical Specifications

Specifications are subject to change without notice. © 2024 VTech Telecommunications, Ltd. All rights reserved. 06/24. VM5467_UK_QSG_V1.

Important Safety Instructions

The applied nameplate is located at the bottom of the baby unit base. When in use, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury, including the following:

1. Follow all warnings and instructions marked on the product.
2. Adult setup is required.
3. CAUTION: Do not install the baby unit at a height above 2 metres.
4. This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such.
5. This product is not intended for use as a medical monitor.
6. Do not use this product near water, for example, near a bath, sink, swimming pool, or shower.
7. CAUTION: Use only the internally, non-user replaceable battery fitted to the parent unit. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperatures and low air pressure at high altitudes during use, storage, or transportation. Disposal of batteries in fire or a hot oven, or mechanically crushing or cutting the battery can result in an explosion. Subjecting products or batteries to an extremely high temperature environment can result in an explosion or leakage of flammable liquids or gas. Products or batteries subjected to extremely low air pressures may result in explosion or leakage of flammable liquids or gas.
8. Use only the power adaptors supplied with this product. Incorrect power adaptor polarity or voltage can seriously damage the product.
9. The power adaptor is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table, or cabinet outlet.
10. For pluggable equipment, the socket-outlet (power adaptor) should be installed near the equipment and should be easily accessible.
11. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
12. Do not modify the power adaptors or replace with other third-party adaptors.
13. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or damaged.
14. The product should only be operated from a power source indicated on the power adaptor label or marking. If you are unsure of the type of power supply in your home, consult your dealer or electricity supply provider.
15. Do not overload wall outlets or use an extension cord.
16. Do not place this product on an unstable table, shelf, stand, or other unstable surfaces.
17. This product should not be placed in any area where proper ventilation is not provided. Any slots or openings in the back or bottom of this product are provided for ventilation. To protect from overheating, openings must not be blocked by placing the product on a soft surface such as a bed, sofa, or rug. This product should never be placed near or over a radiator or heat source.
18. Never insert any objects through any apertures or slots in the product as this can be dangerous and cause damage to the battery or other internal parts. Never spill any liquids on the product.
19. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Disassembling or removing parts of the product other than battery replacement via a battery door (if applicable) may expose dangerous voltages or other risks.
20. You should test the sound reception every time you turn on the units or move one of the components.
21. Periodically examine all components for damage.
22. There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you are not intending to use it for some time.
23. Children should be supervised to ensure that they do not play with the product.
24. The small parts of this monitor can be swallowed by babies or small children. Keep these parts out of reach of children.
25. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Cautions

• Use and store the product at a temperature between 0°C and 40°C.
• Mishandling batteries can cause burn, fire, or explosion hazards.
• Batteries should not be exposed to excessive heat such as bright sunshine or fire.
• Do not expose the product to extreme cold, heat, or direct sunlight. Do not place the product close to a heating source.

Warning--Strangulation Hazard--Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 0.9m away). Do not remove warning label on the adaptor cord.

Never place the baby unit inside the baby's cot or playpen. Never cover the baby unit or parent unit with anything such as a towel or a blanket.

Other electronic products can cause interference to your parent unit and baby unit. Try installing your baby unit as far away as possible from the following electronic devices: wireless routers, radios, mobile telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances (e.g. microwave ovens) and cordless telephones.

What's in the Box

The package typically includes the baby unit, parent unit, power adaptors for both units, and a quick start guide. Specific items may vary.

Setup and Connection

1. Connect the Baby Monitor

Notes:

• The rechargeable battery in the parent unit is built-in.
• Use only the power adaptors supplied with this product.
• Ensure the parent unit and the baby unit are not connected to an electronically/timer controlled electric power outlet.
• Connect the power adaptors in a vertical or floor mount position only. The adaptor prongs are not designed to hold the weight of the baby monitor, so do not connect them to any ceiling, under-the-table, or cabinet outlets. Otherwise, the adaptors may not properly connect to the outlets.
• Ensure the parent unit, the baby unit, and the power adaptor cords are out of reach of children.

1. Connect the Baby Monitor (Continued)

Notes:

• Before using the baby monitor for the first time, charge the parent unit battery for 12 hours.
• When the parent unit battery is fully charged, the battery icon segments become solid ?.
• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time, turn the parent unit off while charging.
• The standby time varies depending on the sensitivity level you set, your actual use, and the age of the battery.

The battery icon indicates the battery status:

• Battery Status: The screen displays and the light flashes.
  Action: The battery has very little charge and may be used for only a short time. Charge without interruption (about 30 minutes).
• Battery Status: The battery icon segments are solid ?.
  Action: The battery is fully charged. To keep the battery charged, connect it to AC power when in use.

2. Power On or Off the Baby Monitor

Connect the baby unit to a power supply to turn it on. Disconnect the baby unit to turn it off.

Press and hold the POWER button ⏻ to power on or off your parent unit.

Once both units are powered on, your parent unit displays images from the baby unit, and the LINK LED light turns on.

Note: Peel off the lens/screen protector before use.

3. Positioning the Baby Monitor

Placement Guidelines:

• Keep the baby unit out of reach of your baby. Never place or mount the baby unit inside the baby's cot or playpen.
• For hearing protection, ensure the parent unit is more than 1 metre (approx. 3 feet) away from the baby unit. If you hear any feedback noise, move the parent unit further away until the noise stops. You can also press VOL- to lower or mute the noise.
• To avoid interference from other electronic devices, place your baby monitor at least 1 metre (approx. 3 feet) away from devices such as wireless routers, microwave ovens, mobile phones, and computers.

Diagram Description: Visuals show placement rules indicating distances greater than 1 meter ('> 1m') and less than 1 meter ('< 1m') between units and objects, emphasizing safe distances for operation and to prevent feedback.

Basic Operation - Parent Unit

Using the Menu

Press the MENU/SELECT button ⚙️ to enter the menu, choose a menu item, or save a setting. Use the parent unit for advanced settings like playing the baby unit lullaby or adjusting sound sensitivity.

• While in the menu:
• Press ◀️ or ▶️ to scroll among menu options.
• Press MENU/SELECT ⚙️ to select an item, confirm a selection, or save a setting.
• Press ▲ or ▼ to scroll among sub-menus or adjust a setting.
• Press RETURN ↩️ to return to previous menu options without changing the current setting.
• Press TALK/RETURN ↩️ to return to live video.

Talk to Your Baby Unit

Press and hold the TALK button ? and speak into your parent unit. Your voice is transmitted to the baby unit. Release TALK when finished talking to hear your baby again.

Turn Off the Screen

Short press the POWER/LCD OFF button ⏻ to turn off the parent unit screen without powering off the parent unit. You will still hear sounds from the baby unit.

Tip: Press any button on the parent unit to turn the screen on again.

Adjust Parent Unit Volume

Press VOL- or VOL+ ? to adjust your parent unit speaker volume.

Pan and Tilt the Baby Unit

Press the Arrow keys ◀️ ▶️ ▲ ▼ to pan and tilt the baby unit.

Note: For optimum reception, always raise the parent unit antenna.

Overview - Parent Unit

Diagram Description: A visual representation of the parent unit with numbered components.

1. Antenna
2. 3-level sound indicator light
3. Battery LED light
4. LINK LED light
5. Arrow keys (Pan/Tilt)
6. Menu/Select button
7. TALK/Return button
8. POWER/LCD OFF button
9. VOL-/VOL+ buttons
10. Speaker
11. USB power jack
12. RESET button

Overview - Baby Unit

Diagram Description: A visual representation of the baby unit with numbered components.

1. Night light key
2. Light Sensor
3. Camera lens
4. Infrared LEDs
5. Microphone
6. Night light
7. PAIR key (Parent unit and baby unit provided are already paired)
8. Speaker
9. Temperature sensor
10. Power jack
11. Slots for wall mounting

Parent Unit Icons and Settings

Main Menu Icons

• Brightness: Adjust the parent unit LCD brightness.
• Lullaby: Play/Stop lullaby. Select one of the soothing sounds or white noise. Select one of the five melodies. Play all melodies. Set a timer to stop playing the selected melody or soothing sound.
• Night Light: Turn on/off night light. Select one of the night light colours. Select all seven colours in sequence. Set a timer to turn the night light off, or to always on. Set to turn on the night light automatically when the baby unit detects sound. It will turn off after 15 minutes of no sound detection.
• Screen Off Timer: The parent unit screen will turn off after the selected time to save energy. You can still hear your baby while the screen is turned off.
• Sound Sensitivity: When AUTO is selected, the parent unit screen will automatically turn on when detected sounds exceed a set level. Adjust the baby unit microphone sensitivity level; a higher level means the baby unit is more sensitive in detecting sounds.
• Alert Tone Settings: Set the parent unit to beep when the battery is low. Set the parent unit to beep when the link between the parent unit and the baby unit is lost. Set the confirmation tone on or off when selecting an option in the menus.
• Temperature: Turn on/off temperature alert tone. Set the parent unit to beep whenever the room temperature detected by the baby unit falls outside the set temperature range. Set the minimum temperature. Set the maximum temperature. Set temperature display in Fahrenheit (°F) or Celsius (°C).
• Baby Unit Settings: Adjust the baby unit speaker volume. Zoom in (2X) or out (1X).

Status Icons

• Connection Status: ? Strong signal strength, ? Moderate signal strength, ? Low signal strength, ? Weak signal strength.
• Current View Status: Indicates the baby unit is being viewed.
• Night Vision: ? Night vision is ON.
• Zoom: ? Zoom is ON.
• Mute Alert: Displays when the parent unit speaker volume is set to OFF.
• Talkback: ? Displays when the parent unit is talking to the baby unit.
• Battery Status: ? animates when the battery is charging. ? indicates battery is fully charged. ? indicates battery is low and needs charging.
• Lullaby: ♫ Lullaby is ON.
• Night Light: ? Night light is ON. ? Night light - Auto-on: A red icon indicates the night light is set to auto-on and is currently turned on by sound activation. A grey icon indicates the night light is currently off but is set to auto-on. Night light will turn on when sound is detected by the baby unit.
• Real-time Temperature: ?️ Displays real-time temperature detected by the baby unit in Fahrenheit (°F) or Celsius (°C) (e.g., 57°F or 14°C).
• Temperature Alert Tone: ?️ Alert tone is ON.

Alert Icons

• Displays when parent unit's battery is low and needs charging.
• The parent unit is searching for the baby unit.
• Displays when connection between parent unit and baby unit is lost.
• Baby unit detects temperature reaches or exceeds the set maximum.
• Baby unit detects temperature is at or is lower than the set minimum.

Sound Sensitivity and Sound Activation

Adjust the sound sensitivity level of the baby unit. The parent unit screen will turn on only when detected sounds exceed a set level.

Use the parent unit to adjust the microphone sensitivity of your baby unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds that transmit to the parent unit. The sound sensitivity level is preset to the highest level.

Press ⚙️, go to Screen Off Timer, select AUTO to adjust the sound sensitivity.

Sound Sensitivity Level Descriptions:

• Level 5 (Highest): The parent unit screen turns on for loud crying or screeching sounds from your baby. It remains off when your baby makes soft sounds.
• Level 4 (High): The parent unit screen turns on for loud babbling and louder sounds from your baby. It remains off when your baby makes soft sounds.
• Level 3 (Medium): The parent unit screen turns on for soft babbling and louder sounds from your baby. It remains off when your baby sleeps soundly.
• Level 2 (Low): The parent unit screen turns on for quiet sounds (including background noises) from your baby's room.
• Level 1 (Lowest): The parent unit screen turns on for crying and louder sounds from your baby. It remains off when your baby makes soft sounds.

When AUTO is selected, the parent unit screen stays off to save power when the baby unit detects sounds that are lower than the set sensitivity level. Once the baby unit detects sounds that are louder than the set sensitivity level, the parent unit screen turns on automatically. It will then turn off again after 50 seconds if the sounds detected are lower than the set sensitivity level.

Dim Mode

Dim mode helps you save parent unit power. When your parent unit is not charging, the display will automatically dim after 10 minutes of inactivity if no keys are pressed or alerts are received from the baby unit.

Diagram Description: Shows the screen dimming after 10 minutes of inactivity and turning back on when a button is pressed.

Night Vision

The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark room. When the baby unit detects low light levels, the infrared LEDs are switched on automatically. The images from the baby unit are in black and white, and appear on the parent unit screen.

Notes:

• A click sound from the baby unit is normal and occurs when your unit adapts to the environment lighting conditions.
• To achieve accurate and high-quality video, your baby unit is equipped with an Infrared cut-off filter lens that optimizes colour accuracy in bright, day-time environments. When the environment turns dark at night, this filter lens is withdrawn to enhance night vision quality. The brief click sound you hear is from the filter lens activating/deactivating as the unit switches from day to night vision (and vice versa).

Tip: Depending on the surroundings and other interfering factors, for example, lighting, objects, colours, and backgrounds, the image quality may vary. Adjust the baby unit angle or place the baby unit at a higher location to prevent glare and a blurred display.

Mount the Baby Unit (Optional)

You may need to purchase screws and wall plugs separately for wall mounting, depending on your wall composition.

Mounting Steps:

1. Insert screws into the wall holes and tighten until only 6.5 mm of the screws are exposed.
2. Note: Check for reception strength and camera angle before drilling. Use a pencil to mark the position of two holes, ensuring they match the wall mount holes on the baby unit base.
3. Drill two holes in the wall. If drilling into a stud, proceed to step 4. If drilling into an object other than a stud, insert wall plugs into the holes and tap gently with a hammer until flush with the wall.
4. Align the wall mount holes on the baby unit with the screws on the wall. Slide the baby unit down until it locks into place.
5. Adjust the camera angle as needed.

General Product Care

To keep this product working well and looking good:

• Avoid placing near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps).
• DO NOT expose to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft damp cloth.
• DO NOT immerse the parent unit or the baby unit in water and do not clean under running water.
• DO NOT use solvents, household cleaning sprays, or liquid cleaners.
• Make sure the parent unit and the baby unit are dry before reconnecting to the mains supply.

Storage

When not in use for some time, store the parent unit, baby unit, and adaptors in a cool, dry place.

Adult Supervision

• This baby monitor is for adult use only.
• Do not place the baby unit inside the cot or playpen.
• To ensure your children's safety, do not allow them to touch or play with the baby monitor and its accessories. This is NOT a toy.

Disposal of Batteries and Product

The crossed-out wheelie bin symbols on products and batteries, or their packaging, indicate they must not be disposed of in domestic waste as they contain substances damaging to the environment and human health. Chemical symbols Hg, Cd, or Pb indicate the battery contains mercury, cadmium, or lead above specified limits. Help protect the environment by disposing of your product or batteries responsibly.

Declaration of Conformity

This product is intended for use within Europe and the UK. This equipment complies with the essential requirements of the EU Radio Equipment Directive (2014/53/EU) and the UK Radio Regulations 2017 on radio systems and telecommunication equipment. VTech Telecommunications Ltd. declares that the 5" Pan & Tilt Monitor VM5467 complies with the essential requirements and other relevant provisions of the EU Radio Equipment Directive (2014/53/EU) and UK Radio Equipment Regulations 2017. The Declaration of Conformity for the VM5467 is available from www.vtechphones.eu.

Customer Service and Product Warranty

Product Warranty

Thank you for choosing this quality product from VTech. The product is covered by a one-year warranty from the date of purchase against defects in materials or workmanship. The product may be returned to the place of purchase. This warranty becomes void if the product is damaged due to misuse, modification, unauthorized repair, faulty batteries, battery discharge, or incorrect electrical connections. This warranty is personal to the original purchaser and is not transferable. Breakages to the LCD screen or damage to the antenna are not covered by the warranty.

IMPORTANT: Please retain your sales receipt as proof of the date of purchase.

Customer Service

For assistance, please visit www.vtechphones.eu to contact the Customer Services Department.

Manufacturer: VTech Telecommunications Ltd., 23/F., Tai Ping Industrial Centre, Block 1, 57 Ting kok Road, Tai Po, Hong Kong.

Importer: VTech Electronics Europe Plc, Napier Court, Abingdon Science Park, Abingdon, Oxon, OX14 3YT, U.K.

This warranty is offered as an extra benefit and does not affect consumers' statutory rights. This warranty is valid for the UK and Ireland only. For products purchased outside the UK and Ireland, please contact your local distributor or place of purchase.