Outdoor Flight
1.1 Pairing the Drone and the Remote Control
Press the drone's power button to turn it on, then press the remote control's power button (press briefly to turn on, press and hold to turn off). Place the drone on a horizontal surface. The remote control will emit a beep sound (di~), and the drone's body light will flash rapidly, automatically entering pairing mode. Wait a few seconds for the drone's body light to become solid, indicating successful pairing.
[Diagram: Drone, remote control, and arrows indicating the pairing process.]
1.2 Gyroscope Calibration
After completing pairing, you need to calibrate the gyroscope: Simultaneously push the accelerator lever (left lever) and the direction lever (right lever) to the bottom right corner (as shown in the image). At this moment, the drone's indicator light will flash rapidly. Wait a few seconds for the indicator light to turn solid. Release the remote control levers; calibration is complete.
Attention: Calibration must be performed on a horizontal surface.
[Diagram: Illustrating gyroscope calibration by moving control sticks on the remote.]
1.3 Geomagnetic Calibration
Briefly press the 'Geomagnetic Calibration' button. The remote control will emit a beep sound (di~). (As shown in the image), the remote control will emit a beep sound (di~), and the front and rear lights of the fuselage will turn off, indicating the drone is in geomagnetic calibration mode.
- ① Rotate the drone horizontally. The drone's front light will turn on (the remote control will emit a beep sound (di~)), indicating successful horizontal calibration.
- ② After successful horizontal calibration, place the drone vertically with its head facing up and rotate it several times. The drone's rear light will turn on, and the remote control will emit two beep sounds (di~di~), indicating that calibration is successful.
[Diagram: Drone and remote control for geomagnetic calibration.]
1.4 GPS Satellite Search Signal
Once gyroscope and geomagnetic calibration are successful, the drone's head lights will flash rapidly. Then, place the drone on an open surface until the lights change from flashing to solid (this process may take a few minutes). The GPS signal should be 8 or higher for normal takeoff.
Attention: If satellite search fails (the light on the drone's head does not change from flashing to solid), it means the drone is still in optical flow mode, and outdoor takeoff is not recommended.
1.5 Drone Unlock
Use the remote control to operate the drone. It must be unlocked to start. Briefly press the unlock button on the remote control (as shown in the left image below). Alternatively, simultaneously push the left lever to the bottom left corner and the right lever to the bottom right corner (as shown in the right image below), then immediately release both levers. At this moment, all four propellers will rotate at a uniform speed, indicating successful unlocking. Once unlocked, the drone can fly normally.
[Diagrams: Remote control showing stick movements for unlocking the drone.]
1.6 QR Code Video Tutorial for Outdoor Flight
(Please scan the QR code to watch)
French/English Labels: Français/French, Anglais/English
Notes:
- Please fully charge the battery before flying.
- Please try to fly the drone in an open and well-lit environment.
Indoor Flight
2.1 Pairing the Drone and the Remote Control
Press the drone's power button to turn it on, then press the remote control's power button (press briefly to turn on, press and hold to turn off). Place the drone on a horizontal surface. The remote control will emit a beep sound (di~), and the drone's body light will flash rapidly, automatically entering pairing mode. Wait a few seconds for the drone's body light to become solid, indicating successful pairing.
[Diagram: Drone, remote control, and arrows indicating the pairing process.]
2.2 Gyroscope Calibration
After completing pairing, you need to calibrate the gyroscope: Simultaneously push the accelerator lever (left lever) and the direction lever (right lever) to the bottom right corner (as shown in the image). At this moment, the drone's indicator light will flash rapidly. Wait a few seconds for the indicator light to turn solid. Release the remote control levers; calibration is complete.
Attention: Calibration must be performed on a horizontal surface.
[Diagram: Illustrating gyroscope calibration by moving control sticks on the remote.]
2.3 Turn Off Drone's Obstacle Avoidance Function
Please turn off the laser obstacle avoidance function when flying indoors. The method of deactivation is as follows:
[Diagram: Remote control highlighting the button used to disable the obstacle avoidance function. Text on diagram: "Press and hold this button (on the left) to disable the obstacle avoidance function."]
2.4 Disable GPS Mode
The default mode is GPS mode upon power-on. For indoor flight, you need to switch to indoor mode (turn off GPS) to take off normally. The method of switching is as follows:
[Diagram: Remote control showing the GPS mode switch button. Text on diagram: "GPS mode switch button. Press and hold to turn on / off."]
2.5 Drone Unlock
Use the remote control to operate the drone. It must be unlocked to start. Briefly press the unlock button on the remote control (as shown in the left image below). Alternatively, simultaneously push the left lever to the bottom left corner and the right lever to the bottom right corner (as shown in the right image below), then immediately release both levers. At this moment, all four propellers will rotate at a uniform speed, indicating successful unlocking. Once unlocked, the drone can fly normally.
[Diagrams: Remote control showing stick movements for unlocking the drone.]
2.6 QR Code Video Tutorial for Indoor Flight
(Please scan the QR code to watch)
French/English Labels: Français/French, Anglais/English
Observation: For more details on operation, please refer to the 'Four-axis Aerial Drone GPS'.
Notes:
- Please fully charge the battery before flying.
- Please try to fly the drone in an open and well-lit environment.
