Brizo Two Handle Wall Mounted Tub Filler

Important Safety Information

CAUTION

Failure to read these instructions prior to installation may result in personal injury, property damage, or product failure. Manufacturer assumes no responsibility for product failure due to improper installation.

WARNING

Consult local plumbing codes to determine whether a water-temperature-limiting device is required in your installation.

You May Need

• Silicone
• 3/32" & 1/8" tools
• Teflon tape

Handle Installation (for models with threaded bases)

Diagram shows parts 1-5 for handle installation. Stems (1) are installed into valves (2) and secured with screws (3). Handle sleeves (4) are threaded onto valves, then handles (5) are attached. Instructions detail alignment for hot and cold sides, ensuring handles are horizontal. Notes advise on potential valve swapping and handle orientation adjustments.

Handle Base Installation (for models with separate bases)

Diagram shows parts 1-5 for handle base installation. Plasterguards (1) are removed and discarded. Handle base (2) and gasket (3) are placed over stem (4) and secured against the wall with nut (5). The nut is reversible for different wall thicknesses. Optional: Apply sealant to the back surface of flanges if the mounting surface is uneven.

Handle Installation (for models with separate bases) - Continued

Diagram shows parts 1-6 for handle installation with separate bases. O-rings (1) are installed onto the splined handle adapter (2). The adapter is installed onto the hot-side (left) valve stem (3) and secured with screw (4). The handle (5) is installed onto the adapter. Measure the gap between the handle and handle base (6). Remove the handle and adapter, mark the distance from the adapter end, and cut the adapter at the nearest notch if necessary. Reinstall the adapter onto the hot-side stem and secure with the screw. Ensure the hot-side valve stem is rotated counter-clockwise as far as possible, and install the handle so the lever is horizontal and points left. Repeat steps A-D for the cold-side (right) valve stem, ensuring the stem is rotated clockwise as far as possible and the handle lever points right. If handles do not install horizontally, rotate the adapter by one spline and reinstall. Notes mention that hot and cold valves may be swapped in the rough plumbing to change handle rotation direction.

Flush Your System

Turn both faucet handles to the full open position. Turn on hot and cold water supplies and flush water lines for one minute. This process removes any debris that could damage internal parts or disrupt water flow. After flushing, turn handles to the off position.

Spout Flange and Spout Installation

Diagram shows parts 1-5 for spout installation. Install gasket (1) onto brass nut (2). Install the nut onto the rough plumbing and tighten until it is against the finished wall. Install the spout tube adapter (3) and tighten until it bottoms out against the brass nut. Push the spout assembly (4) over the adapter until the spout base is flat against the wall. Secure the spout by tightening the set screw (5) on the underside of the spout base, ensuring it engages the groove in the brass nut. Optional: Apply suitable sealant to the gasket on the brass nut if the mounting surface is uneven.

Maintenance - Valves

Diagram shows various parts (1-15) for valve and spout maintenance. To address leaks from the spout or around the handle body, replace the valve cartridge (1). Steps include shutting off water, removing the handle (10) and nut (5), removing the screw (7) and spline adapter (6), unscrewing the sleeve (2) counter-clockwise, and unscrewing the cartridge (1) counter-clockwise using a 19mm hex socket wrench. Install the new cartridge and reassemble in reverse order, aligning handles with valves in the closed position.

Maintenance - Spout

To address leaks at the base of the spout, replace the o-ring (12) on the spout adapter (11). Shut off water supplies. Loosen the set screw (13) on the spout escutcheon and pull the spout straight out from the adapter. Replace the o-ring (12) on the adapter (11) and reassemble. If the leak continues, replace the adapter (11) (part number RP93535). If leaks occur around the stream straightener (14), replace the stream straightener assembly. Carefully pry the stream straightener out using the tabs on its side. Ensure the o-ring (15) is installed on the replacement stream straightener and push it into the spout opening until fully seated.

Cleaning and Care

Clean this product with care. Although its finish is durable, it can be damaged by harsh abrasives or polish. To clean, gently wipe with a damp cloth and blot dry with a soft towel.

Limited Warranty

Parts and Finish

Brizo faucets purchased from authorized sellers are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer owns the home. For commercial purchasers, the warranty period is ten (10) years for multi-family residential applications and five (5) years for all other commercial uses.

Electronic Parts and Batteries

Electronic parts (excluding air switch power modules and batteries) are warranted to the original consumer purchaser for five (5) years from the date of receipt. For commercial users, this period is one (1) year. No warranty is provided on batteries.

Air Switch Power Module

The electronic power module for Brizo air switches is warranted to the original consumer purchaser for two (2) years from the date of receipt. For commercial users, this period is one (1) year.

What Brizo Will Do

Brizo Kitchen & Bath Company will repair or replace, free of charge, any part or finish that proves defective under normal installation, use, and service during the applicable warranty period. Brizo may use new, refurbished, or recertified parts. If repair or replacement is not practical, Brizo may refund the purchase price.

What Is Not Covered

This warranty does not cover products purchased from unauthorized sellers. Labor charges for repair, replacement, installation, or removal are not covered. Brizo is not liable for damage from normal wear and tear, outdoor use, misuse, freezing, abuse, neglect, improper assembly, installation, maintenance, or failure to follow care instructions. Customized components and damage from their removal/installation are also not covered.

Obtaining Warranty Service

Contact Brizo Kitchen & Bath Company by calling 1-877-345-BRIZO (2749) or via their website (www.brizo.com/customer-support). Proof of purchase and date of receipt are required unless the product has been registered.

Limitations

Implied warranties are limited to the statutory period or the duration of this warranty, whichever is shorter. Special, incidental, or consequential damages are excluded to the maximum extent permitted by law.

This warranty gives you specific legal rights, and you may have other rights that vary by state/province. This is Brizo Kitchen & Bath Company's exclusive written warranty and is not transferable.