Brizo Instant Hot Water Dispenser Installation Guide
This guide provides instructions for installing the Brizo Instant Hot Water Dispenser. Please read all instructions before beginning installation.
Important Safety Information
CAUTION: This system dispenses near-boiling water. Exercise care and supervision to avoid scalding.
Failure to read these instructions prior to installation may result in personal injury or property damage. The manufacturer assumes no responsibility for product failure due to improper installation.
Product Overview
The Brizo Instant Hot Water Dispenser provides convenient access to hot water. It is designed to be used with an Insinkerator® Digital Instant Hot Water Tank (HWT300-F2000S or HWT300).
Model Number: 103280
For assistance or replacement parts, visit: www.brizo.com/customer-support
Register your product online: www.brizo.com/customer-support/product-registration
Installation Instructions
Tools and Materials Needed:
- Insinkerator® Digital Instant Hot Water Tank (HWT300-F2000S or HWT300)
- Supplied Wrench
- Optional: Filter (recommended for optimal performance)
Step 1: Faucet Installation
- Slide the faucet base down.
- Slide the 5/16" Clear Silicone Vent Line up underneath the base and secure it to the white fitting.
- Slide the base back up, securing it to the faucet body. Ensure the Brizo logo faces forward.
- Insert the 7/16" Clear Silicone Supply Line onto the gray fitting.
- Slide the gasket onto the tubes with the paper backing oriented up. Remove the paper backing to expose the adhesive and install the gasket.
- Insert the faucet into the sink, ensuring it is centered in the hole.
- Install mounting hardware with the supplied wrench until snug.
- Adjust the final position of the faucet above the sink if necessary.
- Tighten hardware until the faucet resists movement, being careful not to overtighten.
Note: Faucet fittings are 1/4" compression. Ensure all fittings and end connections are free of debris. Loop tubing if it is too long, maintaining a minimum bend diameter of 8". Secure the metal nut to the adapter, start by hand, and then tighten with a wrench for at least 2 more turns.
Step 2: Tank Installation
- Install the Insinkerator tank according to the manufacturer's instructions.
- Install the inlet and outlet tubes as shown in the diagram. The inlet tube should make a "click" sound when secure.
CAUTION: Do not plug in the hot water tank until all water connections are made and checked for leaks.
Step 3: Filter Installation (Recommended)
- Install the filter according to the Insinkerator manual.
Note: It is recommended that carbon filters be replaced every 6 months.
Step 4: Connections
- Make connections to the cold water supply.
- Check all connections for leaks.
- Run the faucet for 4 minutes prior to turning on the tank.
Troubleshooting
| Problem | Possible Cause | What to Do |
|---|---|---|
| Water and steam spits forcefully from spout without turning on the dispenser. | Unit is boiling. May be normal during initial set-up. | Depress or twist hot water dispenser handle to release some water. Adjust water temperature using the digital display on the tank. Remember that at higher altitudes, water boils at lower temperatures. |
| Water is not hot. | The unit is unplugged. The electric outlet is inoperative. The power button is not on. | Ensure the unit is connected to a correctly earthed electric outlet. Check that the outlet is not switched off. Ensure the circuit breaker or fuses are functioning correctly. |
| Water is too hot or not hot enough. | Thermostat is not adjusted to your needs. | Adjust the thermostat, then depress or twist the hot water dispenser handle for 20 seconds to bring in fresh water. Allow 5-7 minutes for water to reach the new temperature. |
| Water comes out of the vent instead of spout. | Outlet tube from tank is blocked. | Check that the outlet tube is not kinked, twisted or pinched. Unscrew the spout end piece and clean out any debris. |
| Water is dripping from the spout/vent intermittently. | The tank expansion chamber is not draining properly due to low water pressure. The spout is blocked. Did not use recommended tank. | Unplug the unit. Check the supply valve to ensure it is fully open and there are no obstructions in the water line reducing pressure below 15 psi (103 kPa). Unscrew the spout end piece and clean out any debris. Use a tank model listed in the installation materials. |
| Water is dripping from the spout/vent constantly. | Debris in the water line may be in the dispenser valve seat, causing a slow water leak. | Unscrew the spout end piece and clean out any debris. Depress or twist the hot water dispenser handle 7-10 times to flush the dispenser and lines. |
| Divided stream. | Debris in the end piece. | Unscrew the spout end piece and clean out any debris. |
| Water discoloration/rusty appearance. | Corrosion of unit. | Unplug and drain the unit as described in the Care and Use section of the InSinkErator manual. If the discoloration remains, discontinue use and contact InSinkErator. |
| Excessive splashing when in use. | Using with handle fully open. | Open the handle partially and adjust until splashing subsides. There is a slight delay between handle adjustment and water exiting the faucet. |
Limited Warranty on Brizo® Faucets
Parts and Finish: Brizo® faucets are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original purchaser owns the home. For commercial purchasers, the warranty period is ten (10) years for multi-family residential applications and five (5) years for all other commercial uses.
Electronic Parts and Batteries: Electronic parts are warranted for five (5) years from the date of purchase for consumers, and one (1) year for commercial users. No warranty is provided on batteries.
Air Switch Power Module: Warranted for two (2) years from the date of purchase for consumers, and one (1) year for commercial users.
What We Will Do: Brizo Kitchen & Bath Company will repair or replace, free of charge, any part or finish that proves defective under normal installation, use, and service.
What Is Not Covered: This warranty does not cover products purchased from unauthorized sellers, labor charges, damage from reasonable wear and tear, outdoor use, misuse, freezing water, abuse, neglect, or improper installation or maintenance. Customized components and their installation are also not covered.
To Obtain Warranty Service or Replacement Parts: Call 1-877-345-BRIZO (2749) or contact Brizo Kitchen & Bath Company via mail or online at https://www.brizo.com/customer-support/contact-us. Proof of purchase is required unless the product has been registered.
Additional Rights: This warranty gives you specific legal rights, and you may also have other rights which vary from state/province to state/province.
© 2022 Masco Corporation of Indiana
Brizo
Customer Support : Brizo
