Propel SNAP 2.0™ Compact Folding Drone with HD Camera

Introduction and Safety Information

This document provides instructions for the Propel SNAP 2.0™ Compact Folding Drone with HD Camera. Please read all instructions carefully before operating the drone.

Regulatory Compliance

FCC Part 15 Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC/IC Radiation Exposure: This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

Industry Canada Notice (Canada Only): This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.

Product Overview

The Propel SNAP 2.0™ is a compact, folding drone equipped with an HD camera capable of capturing 1280 x 720 pixel video at 30 frames per second. It features a 6-axis gyro for stable flight, multiple speed settings, and a wide range digital radio for up to 300 feet flight range.

Package Contents

• ? SNAP 2.0™ Drone
• 2.4G Wireless Controller
• Spare Parts
• USB Charger ?
• Phone Holder ?
• Foot Pad
• Battery ?
• Instruction Manual ?

Important Warnings

• ⚠️ DO NOT FLY YOUR SNAP 2.0™ IN FOUL WEATHER!
• ⚠️ CHOKING HAZARD - Small parts. Not suitable for children under 3 years.
• ⚠️ Never leave product charging unattended for extended periods of time. Always disconnect the battery from charger immediately after the battery is fully charged.

Getting Started

Features

• Compact Fold-In Design for easy portability.
• Air Pressure Sensor locks flight altitude for stable video footage.
• Takes Video and Still Pictures with On Board HD Camera.
• 6 Axis Gyro for extremely stable flight and maneuverability.
• 3 Speed Settings for beginner to advanced pilots.
• Wide Range Digital Radio allows flight range up to 300 feet.

Remote Control Battery Installation

1. Unscrew and remove the battery cover from the back of the controller. 2. Install 4 fresh "AAA" alkaline batteries into the controller as shown (see diagram A). Replace the battery cover. 3. Turn over the controller and push the power button up. If the power indicator turns on, batteries are properly installed.

Diagram A Description: Shows 4x1.5 volt "AAA" Alkaline Batteries being inserted into the controller.

Charging the SNAP 2.0™ Li-Poly Battery

1. Insert the battery into the charger as shown (see diagram B). 2. Connect the USB end of the cable to your computer's USB port or a USB wall charger (see diagram C). The red LED indicator on the battery will light off while charging and light on when fully charged. Average charging time is approximately 110-120 minutes (via 5.0V-2A USB wall charger). A fully charged battery provides 5-7 minutes of flight time.

Diagram B Description: Shows the Li-Poly battery being placed into the charger.

Diagram C Description: Shows the USB charging cable connected to a computer USB port and the battery.

IMPORTANT: ALWAYS REMEMBER TO UNPLUG YOUR CHARGING CORD WHEN NOT IN USE!

Install the Aircraft Battery

Put the battery into the battery compartment then lock the two ends with the battery locks (see diagram D).

Diagram D Description: Shows the battery being inserted into the drone's battery compartment and secured with battery locks.

How to Expand and Fold Your SNAP 2.0™

Before flying, expand the foldable arms outwards. Turn the drone over, bottom side facing you, and carefully pull and expand the 4 arms until fully extended (see diagram D). After flying, it is recommended to fold all 4 arms back in. Be gentle when expanding or folding.

Drone and Controller Overview

SNAP 2.0™ Diagram

The SNAP 2.0™ drone features four rotors: Propeller A (two on the front) and Propeller B (two on the rear). Key components include the Camera, Power Button, and an Emergency Stop button.

Controller Diagram

The controller includes: Throttle/Yaw control (left stick), Direction Control (right stick), Speed Setting Button, 360° Stunt Rolls Button, Emergency Stop button, ON/OFF & Power Indicator, Auto Start/Land button, and various Trim controls (Turning Left/Right Trim, Moving Forward/Backward Trim, Banking Left/Right Trim).

Diagram D1 Description: Shows the left throttle stick being moved up and down to sync the drone, with LED indicators changing from flashing to solid.

Flight Preparation and Syncing

Flight Preparation

• Ensure 4 "AAA" batteries are in the remote control and the SNAP 2.0™ battery is fully charged.
• Fly in a large, open space (e.g., field or park) with at least 200 feet of clear radius.
• Start the drone on a clean, flat, level surface before take-off.
• For beginners, fly in zero or extremely light wind conditions. Avoid flying too high until experienced.

Syncing Your SNAP 2.0™

Ensure the drone is on a flat level surface and digital trim settings are centered. No other 2.4G devices should be active nearby.

1. Turn off the controller and remove the battery from the drone.

2. Insert the drone battery, place it on a flat surface, and press and hold the power button for a few seconds until the red and white LED lights flash rapidly (see diagram D1).

3. Quickly turn ON the remote. The top red LED light on the controller should flash, and the drone's lights will flash slower.

4. Push the throttle stick all the way up, then pull it all the way down. You should hear a high-pitched beep in both directions. The drone and controller lights will stop flashing and become solid, indicating successful sync.

Tips:

• Sync quickly: Put the drone battery in, then turn on the controller promptly to avoid timing out.
• Sync indoors or in shade to easily see LED indicators.

Basic Flight Operations

Recognizing Front & Rear

The front of the SNAP 2.0™ is indicated by two white/red lights. The rear is indicated by one red light.

Starting/Stopping Rotors

Manual Start/Stop: To start, move both control sticks down and outward simultaneously until rotors spin, then release. Push the throttle stick up to take off. To stop, wait ~10 seconds for automatic stop, or move both sticks down and outward again. To land after takeoff, pull the throttle all the way down.

Auto Start/Land: Press the AUTO START / LAND button on the controller for automatic takeoff or landing. Direction can still be controlled during auto operations to avoid obstacles.

Speed Select Button

The drone has 3 speed settings: 1 (SLOW), 2 (MEDIUM), and 3 (HIGH). The default is SLOW. Press the speed setting button to cycle through speeds. Beeping sounds indicate speed changes, and the controller display may show the current speed.

Flight Control

Use the left throttle stick to control ascent/descent (⬆️/⬇️) and rotation (⬅️/➡️). Use the right direction stick to control forward/backward movement (⬆️/⬇️) and banking left/right (⬅️/➡️).

• Ascend/Descend: Move left throttle stick ⬆️ to ascend, ⬇️ to descend.
• Rotate Left/Right (Yaw): Move left throttle stick ⬅️ to rotate left, ➡️ to rotate right.
• Move Forward/Backward: Move right direction stick ⬆️ to move forward, ⬇️ to move backward.
• Bank Left/Right: Move right direction stick ⬅️ to bank left, ➡️ to bank right.

Flight Practice

Practice basic maneuvers like vertical takeoffs, landings, and turns. Progress to square and cross pattern maneuvers for advanced control.

Advanced Features & App Integration

Adjusting the Trim

Trim controls help correct drifting. If the drone drifts forward, press the FORWARD/BACKWARD TRIM button downward repeatedly. If it drifts backward, press upward. For left/right drift, use the BANKS TRIM button. For spinning, use the LEFT/RIGHT TURN TRIM button. A single long beep indicates the trim is centered. No sound means it's at maximum trim.

Calibrating the SNAP 2.0™

If the drone drifts significantly, recalibrate it: 1. Place the drone on a flat level surface. 2. Ensure the drone and controller are synced and powered on (do not start blades). 3. Move both throttle and control sticks down and to the right corner simultaneously and hold for 5 seconds (see diagram R). The drone's lights will flash and then stop, indicating calibration is complete.

Diagram R Description: Shows controller sticks moved to the bottom-right corner for calibration.

How to Perform 360° Stunt Rolls

1. Hover the drone at least 5 feet from obstacles. Set speed to mode 2 or 3. 2. Press the 360 stunt button (indicated by rapid beeping). 3. Quickly push the right control stick in the desired direction (left or right) to perform a flip.

Diagram S Description: Shows the 360° Stunt Roll Button.

Diagram T Description: Shows controller stick movements for left and right rolls.

Note: Pressing the stunt button again without moving the stick will exit stunt mode.

Emergency Stop

Simultaneously press the "speed setting button" and "stunt button" to stop the drone blades immediately if control is lost.

Live Video Streaming Setup

Your SNAP 2.0™ has an onboard HD camera. To stream video to your mobile device:

1. You need an Apple or Android phone ? and the "Propel 1890" App installed.
2. Install the included phone holder hook onto the controller to secure your phone (see diagram U).

Diagram U Description: Shows the phone holder being attached to the controller.

Propel SNAP 2.0™ WiFi APP Installation

1. Ensure your device is compatible (iOS 7.0+ or Android 4.2.2+).
2. Ensure your device has internet access.
3. For iOS: Search "Propel 1890" in the App Store and install.
4. For Android: Search "Propel 1890" in the Google Play Store and install.
5. Run the app to confirm installation.

Pairing SNAP 2.0™ to Your Compatible Device

1. Charge and install the SNAP 2.0™ battery.
2. On your device, go to Settings and turn ON Wi-Fi ?.
3. Select "Propel 1890" from the Wi-Fi list to connect.
4. Return to the Main Menu.

Quick Start with the App

1. Open the "Propel 1890" App and tap "START". You will see the real-time video stream from the drone's camera.

2. To use your device as a controller, tap the "ON" button to activate control sticks. Tap the drone icon to start motors. You can now fly using your device. Tap the auto-launch icon to take off or land.

3. Tap the photo icon ? to take pictures or the video icon ▶️ to record videos. Media is saved to your device. Access saved media via the folders within the app.

Detailed App Overview

The app provides control sticks, auto-launch/land functions, photo/video capture, and access to settings like calibration and VR mode. A "HELP" section within the app offers further details.

Maintenance and Troubleshooting

Replacing the Propeller Blades

Propellers may need replacement due to damage. Ensure you match the indication numbers (A or B) on the blades to the correct positions on the drone (front/rear, left/right). Unscrew the damaged blade, replace it with the correct new blade, and secure it with the screw. Reattach the blade guard.

Diagram V Description: Illustrates propeller blade identification (A/B) and placement on the drone. Blade Front Left = B, Blade Front Right = A, Blade Back Left = A, Blade Back Right = B.

Troubleshooting Your SNAP 2.0™

Warnings, Care, and Warranty

General Warnings

The SNAP 2.0™ is designed for OUTDOOR use. Blades revolve at high speeds and can cause damage. Stand away from the drone. Warn spectators of its position. Inspect rotor blades before flight.

• Keep hands, hair, and loose clothing away from propellers when power is ON.
• Turn off transmitter and drone power when not in use.
• Use only the included charger for the Li-Poly battery.
• New alkaline batteries are recommended for controller performance.
• Parental supervision is recommended when flying.

Battery Warnings

• Rechargeable Battery: Dispose of Li-Poly batteries properly according to local requirements if they no longer hold a charge.
• Controller Batteries: Do not mix battery types (alkaline, carbon-zinc, NiMH), old/new batteries, or rechargeable/non-rechargeable batteries. Remove batteries before charging. Charge rechargeable batteries under adult supervision. Dispose of exhausted batteries properly. Do not short-circuit terminals. Use only recommended battery types and ensure correct polarity. Do not dispose batteries in fire.

Care and Maintenance

• Remove batteries from the remote control if not used for an extended period.
• Gently wipe the remote control and drone with a clean damp cloth.
• Keep the toy away from direct heat or sunlight.
• Do not submerge the toy in water.
• Parental guidance is recommended for battery installation/replacement.

Limited 90-Day Warranty (North America)

AMAX Group USA warrants this product against electrical or mechanical defects for 90 days from the purchase date. This warranty covers normal consumer use and does not cover damage from shipping, alterations, accident, misuse, abuse, neglect, wear and tear, or unreasonable use. Removal of parts voids warranties. Implied warranties are limited to 90 days. Consequential or incidental damages are excluded.

Repair/Replace Product

For malfunctions, email the warranty center. If a return is necessary, an RMA number and shipping address will be provided. Returns without an RMA will be rejected.

Preparation for Shipping Your Product

Repack the product securely, preferably in original packaging. Ship prepaid and insured. Include the RMA form, daytime telephone number, and email address. Contact the warranty center for out-of-warranty service.

For inquiries, email: customercare@amaxbrands.com

IMPORTANT NOTICE: Contact the warranty department by email BEFORE shipping your product back.