Propel X04 2.4GHz Quadrocopter with HD Camera

Features

• Built-in 6-axis gyroscopic chip keeps the X04 extremely stable in all conditions.
• Incredible maneuverability including 360° aerial stunts!
• LED directional lights make the X04 easy to follow.
• Unique Switch-Blade technology allows operation in either 3-channel or 4-channel modes.
• Takes still photos and records video footage.
• Air pressure sensor locks flight altitude for stable video footage.

Remote Control Battery Installation

1. Unscrew and remove the battery cover from the back of the controller.
2. Install 2 "AAA" alkaline batteries into the controller as shown in Diagram A.
3. Replace the battery cover and secure it.
4. Turn over the controller and short press the power button; the indicator light will turn on and start flashing.

Diagram A shows the battery compartment requiring 2 "AAA" batteries.

Charging the X04 Li-Poly Battery

1. Insert the battery into the charger as shown (see Diagram B).
2. Connect the USB end of the cable to your computer's USB port or a USB wall charger (see Diagram C). A flashing RED indicator light signifies charging is in progress.
3. When the X04 battery is fully charged, the charging indicator light will turn green.
4. Average charging time is approximately 30-40 minutes (using a 5.0V=2A USB wall charger). A fully charged X04 can fly for 5-7 minutes depending on environment and user input.

Note: Additional batteries and rapid wall chargers can be purchased at www.propelrc.com.

IMPORTANT: ALWAYS REMEMBER TO UNPLUG YOUR CHARGING CORD WHEN NOT IN USE!

Diagram B shows the Li-Poly battery being inserted into the charger. Diagram C shows the USB cable connecting to a power source.

X04 Battery Installation

1. Slide the fully charged battery into the X04 battery compartment (see Diagram D).

Note: The X04 has no on/off switch. It automatically turns on when the Li-Poly battery is inserted. To switch off, simply unplug the battery.

CAUTION! NEVER FORCE THE BATTERY IN! The battery fits in only one direction. Use mild force. If it won't slide in easily or go all the way, remove it and try again!

Diagram D illustrates inserting the battery into the X04.

X04 Diagram

The X04 Quadrocopter features front rotor blades (gray color), rear rotor blades (black color), a battery compartment, landing gear, a safety cage, and a digital camera.

Remote Diagram

The remote control includes a power switch, throttle/yaw control, left trim, right trim, speed setting, camera/video button, power indicator, and direction control (forward/backward trim, left/right trim).

WARNING

DO NOT FLY YOUR DRONE IN FOUL WEATHER! ⛈️ ?️ ? ⚡

Syncing Your X04

Important: When syncing your X04 quadrocopter with the controller, ensure the quadrocopter is on a flat, level surface and that your digital trim settings are centered. This ensures proper programming of the 6-axis gyro.

Your X04 uses an automatic 2.4G channel selection system, allowing up to 8 people to fly simultaneously within the same wireless range without interference.

For One Person Play:

1. Before starting, ensure your controller is OFF and the X04's battery is disconnected. Ensure no other 2.4G devices are in the vicinity.
2. Install the X04's battery and place it on a flat, level surface. The LED indicators on the body should start flashing.
3. Turn ON the remote. You will hear beeping sounds, and the white LED lights on the drone should flash slower. Pull the throttle all the way up, then all the way down. You will hear 2 beeps, and the white LED lights will turn solid, indicating successful syncing. If this does not occur, repeat the steps.

For Multi Person Play:

1. Before starting, ensure all X04s and controllers are OFF. Ensure no other 2.4G devices are in the vicinity.
2. Each person must sync their X04 individually to avoid interference. Follow steps 1-3, ensuring no one else is syncing simultaneously.
3. After syncing, leave the player's X04 ON until all quadrocopters have been synced.
4. If interference occurs, all players must turn off their controllers and quadrocopters for 60 seconds before restarting the process.

Note: If no microSDHC card is inserted, the drone's red LEDs will flash constantly.

Preparing for Flight

• Verify that the remote control unit has 2 "AAA" batteries and the X04 is fully charged.
• Ensure your X04 and controller are both powered on.
• Select a large, open space with a radius of at least 50 feet.
• Ensure the area is free of obstacles and bodies of water. Place your X04 on a clean, level, flat surface before takeoff.

DO NOT ATTEMPT TO FLY YOUR X04 IN RAIN, SNOW, HEAVY WINDS, THUNDER, OR LIGHTNING OUTDOORS. IT COULD DAMAGE YOUR PRODUCT AND POSSIBLY EVEN CAUSE BODILY HARM.

Flying Tips

• It is recommended to operate the X04 in a wide space with an ideal radius of 200 feet.
• Parental guidance or adult supervision is suggested at all times.
• If flying with others, ensure all spectators are positioned behind you.
• For best performance, operate the X04 in zero wind conditions, as wind can significantly affect performance.

Recognizing the Front and Rear of the Quadrocopter

The Quadrocopter has four rotors, but a distinct front (forward-facing) and rear (backward-facing) direction. The front is identified by two gray blades (see Diagram F), while the rear has the charging socket and two black propellers. The front of the Quadrocopter displays WHITE LED lights, and the back displays RED LED lights.

Diagram F illustrates the front and rear of the quadrocopter.

Understanding Trim Adjustments

Forward/Backward Trim

If your X04 drifts forward or backward automatically, adjust the FORWARD/BACKWARD TRIM buttons. Push and release the BACKWARD TRIM (B) button to correct forward drift, and the FORWARD TRIM (F) button to correct backward drift, until stable flight is maintained. Regular adjustments may be needed for accurate hovering.

Banking Left/Right Trim

If your X04 banks left or right automatically, adjust the LEFT BANK or RIGHT BANK TRIM buttons. Push and release the RIGHT BANK TRIM (R) button to correct left banking, and the LEFT BANK TRIM (L) button to correct right banking, until stable hovering is achieved. Regular adjustments may be needed for accurate hovering.

Note: Trim adjustments are accompanied by a beep tone. A single long beep indicates the product is center-trimmed. No beeps indicate the trim is at its maximum on a particular side.

Automatically Take Off / Land

Ensure the X04 is properly synced. Simply press the “START/LAND” button on the controller center for automatic takeoff. Press the “START/LAND” button again to descend and land automatically.

Tips: You can also move both control sticks simultaneously down to the inside or outside corners, hold them until the blades start spinning, release the sticks, and then push the throttle stick slowly to take off manually.

Understanding the Altitude Lock Sensor

The X04 features an Altitude Lock function utilizing an air pressure sensor for easier flight control and stability. After takeoff, fly the drone to a safe height and release the throttle. The sensor will lock the drone's altitude, allowing you to focus on directional controls. The drone will attempt to self-correct to the last locked height if affected by external forces. Note that atmospheric conditions may cause slight altitude variations.

Speed Setting Button

The X04 offers 4 speed settings: T (Training), 1 (SLOW), 2 (MEDIUM), and 3 (HIGH). The default setting is 1 (SLOW). Press and release the speed setting button to change speeds. The speed level is indicated by the number of beeps: one beep for slow, two for medium, and three for high.

T (Training) Mode

Press and hold the Speed Setting Button until you hear a long beep to enter T Mode. This mode allows for very slow flight and includes minimum and maximum height limits to aid learning. To exit T Mode, short-press the speed setting button again.

3/4 Channel Select

The X04 can be controlled in 3-channel (beginner) or 4-channel (advanced) mode. The default setting is 4-channel.

To change to 3-channel mode: Press the Throttle Control stick vertically down and release. You will hear 3 short beeps, indicating the X04 is now set to 3CH mode.

To change back to 4-channel mode: Press the Throttle Control stick vertically down and release again. You will hear 4 short beeps, indicating the X04 is now set to 4CH mode.

4 Channel Flight Control

This section outlines basic flight functions for the X04. It is best to practice in a large space initially. As you master controls, you can move to more advanced techniques.

• Move the left Throttle stick up to increase speed and ascend.
• Move the left Throttle stick down to decrease speed and descend.
• Move the left Throttle stick left to turn/spin left.
• Move the left Throttle stick right to turn/spin right.
• Move the right Direction Stick up to move forward.
• Move the right Direction Control down to move backward.
• Move the right Direction Control left to bank left.
• Move the right Direction Control right to bank right.

3 Channel Flight Control

This section outlines basic flight functions for the X04. It is best to practice in a large space initially. As you master controls, you can move to more advanced techniques.

• Move the Left Throttle Stick up to increase speed and accelerate.
• Move the Left Throttle Stick down to decrease speed and descend.
• Move the Right Directional Stick LEFT to spin/turn left.
• Move the right directional stick RIGHT to spin/turn Right.
• Move the Right Direction Stick forwards to move forward.
• Move the Right Direction Stick backwards down to move backwards.

Calibrating the X04

If the X04 becomes unstable during flight, calibrate the internal gyros by placing it on a flat, level surface. The LEDs on the X04 will flash quickly and then remain solid, indicating recalibration (see Diagram E).

Diagram E shows the calibration process.

How to Do 360° Stunt Rolls

1. Ensure your battery is fully charged. Note: 360° stunt rolls are not possible in T-Mode, Mode 1, or when the drone battery is low (indicated by flashing LEDs).
2. Press and release the "STUNT" button on the top right of the controller (see Remote Diagram, page 3). You will hear beeping sounds, indicating you are in "STUNT MODE."
3. Quickly move your right control stick in any of the four directions (up, down, left, or right). Your X04 drone will instantly roll in the selected direction.

Note: The beeping sounds will stop after the stunt roll. Repeat steps 2-3 to perform another roll.

The diagram illustrates a 360° stunt roll.

Using Your Onboard Camera and Video Recorder

Your X04 is equipped with an onboard digital camera for taking both video and still photographs, allowing you to create aerial photography and videos.

What You Will Need to Get Started:

• One microSDHC card (not included).
• One microSDHC card reader (included).
• One Computer with USB port and a media player capable of playing AVI files (e.g., Windows Media Player, not included).

Formatting Your microSDHC Card:

Before taking photos or videos, format your microSDHC card. Place the card into the included USB card reader and plug it into your computer's USB port (See Diagrams 1 and 2). An icon should appear on your Desktop. Right-click the icon and follow the instructions to format the card.

Installing the microSDHC Card in Your X04 Quadrocopter:

• Do not install or remove the battery first.
• Place the formatted microSDHC card into the quadrocopter's digital camera port at the back (see Diagram 3). Push gently and consistently until you hear and feel the card "click" into place.
• Reconnect the quadrocopter battery. Ensure it is fully charged and properly synced to the controller (see HOW TO SYNC YOUR DRONE on page 4).
• When the microSDHC card is successfully installed and the quadrocopter is powered on, solid red LED lights should appear on the quadrocopter's belly.

Note: Flashing red LED lights indicate the microSDHC card was not installed correctly or there is a problem with the card. Ensure the product is not in Video Record mode, then reformat the card and try again.

Taking Digital Photos:

Press and release the CAMERA/VIDEO button on the top of the controller (refer to CONTROLLER DIAGRAM on page 3). A "beep" sound and a single flash of the red LED tail lights indicate a picture has been taken. The camera ready light will become solid when ready for the next photograph.

Recording Videos:

Ensure your quadrocopter is fully charged and the microSDHC card is correctly installed. Begin recording by pressing and holding the CAMERA/VIDEO button for a few seconds (see CONTROLLER DIAGRAM on page 3). The X04's red LEDs will flash constantly to indicate video mode and recording. Press the button again to stop recording. The red LEDs will change to solid, indicating the camera is in ready mode.

IMPORTANT NOTICE: You cannot take photos and videos simultaneously. If you are in video mode, you must exit it before taking still photos.

Diagram 1 shows the microSDHC card. Diagram 2 shows the USB card reader. Diagram 3 shows the microSDHC card being inserted into the quadrocopter's camera port. Diagram 4 shows the red LED light indicator.

Removing Your microSDHC Card

To remove the microSDHC card, push in gently on the back of the card until you hear and feel a "clicking" sound. The card will pop out slightly and is ready for removal. Gently pull the card away from the quadrocopter camera port. Always store your microSDHC card in a clean, safe, and cool environment.

Downloading and Clearing Space on Your microSDHC Card

Plug your microSDHC card into the card reader and connect it to your computer. It is recommended to download all videos and pictures to your computer and not store them on the microSDHC card. After downloading, follow your computer's instructions to "delete" files on the microSDHC card.

IMPORTANT NOTICE: When your microSDHC card is full, the indicator light on the bottom of your quadrocopter will not flash when you press the photograph or video record buttons. This indicates it's time to insert a new SD card or download and clear space for new photos and videos.

Replacing the Propeller Blade

The X04 propeller system is a precision instrument that may require repair or replacement for optimal flight. Crash landings from high-speed aerial flights can damage propellers.

1. The X04 has four blades: two gray ones at the front and two black ones at the back (see Diagram L).
2. When replacing blades, match the color and indication letter on the new blades with those shown in Diagram L.
3. To replace a blade, gently pull off the broken blade and push the new correct blade into place.

Diagram L shows the front and rear blades with their corresponding letters (A, B).

X04 Warning

The X04 is designed for INDOOR or OUTDOOR use. The X04 blades revolve at high speeds and can cause damage to users, spectators, and animals. Maintain a safe distance from the X04 to avoid the flight path. Warn spectators of the drone's position before flying. Before flight, inspect rotor blades to ensure they are securely fastened.

• WARNING! ⚠️ Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades.
• Keep hands, hair, and loose clothing away from the propeller when the battery is plugged into the drone.
• Turn off the transmitter and unplug the X04 battery when not in use.
• The included charger is built specifically for the X04 Li-Poly battery; do not use it to charge any other battery.
• New alkaline batteries are recommended for maximum performance.
• Parental supervision is recommended when flying the X04.

Battery Warnings

Rechargeable Battery:

This X04 uses a Li-Poly rechargeable battery. If the battery can no longer be charged, dispose of it properly according to local disposal requirements.

Controller Batteries:

The remote control requires 2 "AAA" batteries (not included). Please read the important battery safety warnings below:

• Do not mix alkaline, standard (carbon-zinc), and rechargeable (Nickel Metal Hydride) batteries.
• Do not mix old and new batteries.
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries must be removed from the item before being charged (if removable).
• Rechargeable batteries are only to be charged under adult supervision.
• Exhausted batteries should be removed immediately and recycled or disposed of properly according to state or local government ordinances and regulations.
• The supply terminals are not to be short-circuited.
• Only batteries of the same or equivalent type as recommended should be used.
• Batteries must be inserted with the correct polarity (refer to the diagram inside the booklet).
• Do not dispose of batteries in fire, as they may leak or explode.

Care and Maintenance

• Always remove batteries from the wireless infrared remote control when it is not being used for an extended period.
• To clean, gently wipe the remote control and X04 with a clean, damp cloth.
• Keep the toy away from direct heat or sunlight.
• Do not submerge the toy in water, as this can damage the unit beyond repair.
• Parental guidance is recommended when installing or replacing batteries.

Limited 90-Day Warranty (North America)

ROOFTOP BRANDS™ warrants to the original consumer that this product is free from any electrical or mechanical defects for a period of 90 DAYS from the date of purchase. If any such defect is discovered within the warranty period, ROOFTOP BRANDS™ will repair or replace the unit free of charge upon receipt of the unit, shipped postage prepaid and insured to our warranty center. The warranty covers normal consumer use and does not cover damage that occurs in shipment or failure resulting from alterations, accident, misuse, abuse, neglect, wear and tear, inadequate maintenance, commercial use, or unreasonable use of the unit. Removal of any parts/components voids all warranties. This warranty does not cover the cost of repairs made or attempted by third-party individuals or companies. Any applicable implied warranties, including warranties of merchantability and fitness, are hereby limited to 90 DAYS from the date of purchase. Consequential or incidental damages resulting from a breach of any applicable express or implied warranties are hereby excluded. Some states do not allow limitations on the duration of implied warranties and do not allow exclusion of incidental or consequential damages, so the above limitations and exclusions may not apply in these instances.

Repair/Replace Product:

If your product begins to malfunction or stop working, immediately call or email our warranty center at the phone/email listed below. If a return is deemed necessary, our warranty department will issue you an RMA number/form and an address to the nearest return center for shipping the product. IMPORTANT NOTICE: We will reject all returns not accompanied by an issued RMA form and number, so be sure to contact our warranty center before attempting to return your product!

Preparation for Shipping Your Product:

Please repack your product in a durable box, preferably the original carton, and send it prepaid and adequately insured. Include the RMA form issued by our warranty department, along with your daytime telephone number and email address (if available), inside the shipping carton. If your warranty has expired, contact our warranty center for charged service. For further information, please send all inquiries to customerservice@rooftopbrands.com.

IMPORTANT NOTICE!

DO NOT ATTEMPT TO SHIP YOUR PRODUCT BACK WITHOUT FIRST CONTACTING OUR WARRANTY DEPARTMENT AT:

ROOFTOP BRANDS™ WARRANTY REPLACEMENT DEPARTMENT
customerservice@rooftopbrands.com