Cecotec Ready Warm 3100 Smart Now

Safety Instructions

Read these instructions thoroughly before using the appliance. Keep this manual for future reference or new users.

• Ensure mains voltage matches the rating label and the wall outlet is grounded.
• This appliance is for household use only, not for industrial or commercial purposes.
• Regularly check the power cord for visible damage. If damaged, it must be replaced by Cecotec Technical Support to avoid danger.
• Do not place near heat sources, flammable substances, or wet surfaces. Avoid contact with water or other liquids. Do not operate outdoors.
• Place on a flat, stable, and safe surface; do not cover.
• Do not place immediately below a power socket.
• Do not immerse the cord, plug, or any non-removable part in water or other liquids. Ensure hands are dry before handling the plug or switching on.
• The appliance is not for children under 8. Children aged 8 and above can use it with continuous supervision.
• Persons with reduced physical, sensory, or mental capabilities, or lack of experience, can use it if supervised or instructed on safe use and hazards.
• Supervise children to ensure they do not play with the appliance. Close supervision is necessary when used by or near children.

Before Use

1. Remove the product from the box and all packaging materials.
2. Check for any visible damage. If observed, contact Cecotec Technical Support for advice or repair.

Product Assembly

Floor Installation

To assemble the unit on the floor:

1. Place the product upside-down on a soft, stable surface.
2. Attach one wheel-mounting plate to one end of the product, ensuring it fits into the gap between the two wheels.
3. Use a provided screw to fix the mounting plate to the heater.
4. Repeat steps 2 and 3 for the other wheel-mounting plate on the opposite end.

Diagram Description: A side view illustrating the attachment of wheel mounting plates to the base of the heater, showing how they align with the wheels.

Wall Installation

To mount the unit on a wall:

1. Drill two holes on the wall following these measurements: Diameter: 8 mm, Depth: 35 mm, Distance between holes: 120 mm.
2. Insert wall anchors into the drilled holes and then insert screws into the anchors.
3. Screw them in properly and ensure they are securely fixed.
4. Place the appliance against the wall so that the screws align with the holes on the appliance's back.

Diagram Description: A side view of the heater's rear showing mounting holes, with accompanying measurements indicating the required hole spacing (120 mm) and diameter (8 mm).

Operation

Display Symbols

• L: Low-Power Heating (1000 W)
• H: High-Power Heating (2000 W)
• °C: Temperature Setting (15 °C - 35 °C)
• Timer Symbol: Timer Setting (Power On/Off from 1 to 24 hours)

Thermostat

• Select the desired temperature, which will be displayed.
• The appliance automatically turns off when the set temperature is reached.
• It automatically turns on to maintain the set temperature when the ambient temperature drops below the set point.
• The appliance remembers the last set temperature and operates accordingly, as long as it is not disconnected.

Timer

• The heater has a timer function for automatic power-on or power-off, programmable from 1 to 24 hours.
• When timer mode is selected, the timer symbol will blink, and the display will show the remaining time.

Safety System

• Features an auto-reset thermostat that automatically turns off the heater at very high surface temperatures and turns it on at very low surface temperatures.
• Includes a disposable thermal fuse for product and user safety in case of overheating.

Remote Control

1. With the product off, press the power button to activate low-power heating. Press it again when the product is on to turn it off.
2. Press the mode button to select or change the operating mode.
3. Press the timer button (⊙) to enter timer mode and use the △ and ∇ buttons to select the desired hour.
4. During operation, use the △ and ∇ buttons to increase or decrease the temperature.

Cleaning and Maintenance

• Turn off, unplug, and allow the appliance to cool before cleaning.
• Do not use abrasive scouring pads, powders, or cleaning products.
• Use a soft, damp cloth to clean the exterior.
• If the heater is not used for an extended period, store it in a dry, safe place protected from dust.

Technical Specifications

• Model: Ready Warm 3100 Smart Now
• Reference: 05322
• Power: 2000 W
• Voltage: 220-240 V
• Frequency: 50 Hz
• Origin: Made in China | Designed in Spain

Disposal of Old Electrical Appliances

In accordance with European Directive 2012/19/EU (WEEE), electrical appliances must not be disposed of with municipal waste. They should be collected separately for material recovery and recycling to reduce environmental and health impacts. The crossed-out wheeled bin symbol indicates the obligation for correct disposal. If the product contains batteries, they must be removed and disposed of separately. Contact local authorities for detailed disposal information.

Warranty and Technical Support (SAT)

This product has a 2-year warranty from the date of purchase, provided the purchase invoice is presented, the product is in perfect physical condition, and it has been used correctly as per the manual.

Warranty Exclusions:

• Misuse, damage from impact, exposure to moisture, immersion in liquids, corrosive substances, or any fault attributable to the consumer.
• Disassembly, modification, or repair by unauthorized persons.
• Wear and tear from normal use.

The warranty covers manufacturing defects for 2 years, excluding consumable parts. Misuse voids the warranty.

For any issues or queries, contact Cecotec Technical Support Service at: +34 963 210 728.

Contact Information

Grupo Cecotec Innovaciones S.L.
C/ de la Pinadeta s/n, 46930 Quart de Poblet, Valencia, Spain

Website: www.cecotec.es