Nordrive K9 Fit Kit Installation Guide
Product Overview
This document provides installation instructions for the Nordrive K9 Fit Kit, designed for use with Nordrive SNAP roof bar systems. It details the components and steps required for secure mounting.
Product Name: FIT KIT K
Model Number: N21419 K9
Maximum Load Capacity: 75 Kg.
Certifications: TÜV SÜD, GS Geprüfte Sicherheit (Tested Safety).
Before proceeding with these instructions, please consult the relevant S or X+P manual for comprehensive guidance.
Clamp Kit Contents
The K9 Fit Kit includes the following components for assembly:
- Component 40FE0249 (x4)
- Component 40FE0322 (x4)
- M6x16 Screw 60CE6016 (x4)
- Component 60BE8012 (x1)
- Component 61ED0611 (x4)
- Component 62BB0800 (x4)
- Component 61FN0612 (x4)
- Tool 72FE0002 (x1)
Compatible SNAP Roof Bar Systems
The K9 Fit Kit is designed to work with various Nordrive SNAP roof bar systems:
- SNAP STEEL: Model N15010 (S, 5.5Kg), N15012 (L, 6.3Kg)
- SNAP STEEL RAIL: Model N15014 (S, 5.8Kg), N15016 (L, 6.6Kg)
- SNAP ALU: Model N15011 (S, 3.4Kg), N15013 (L, 3.8Kg)
- SNAP ALU RAIL: Model N15015 (S, 3.7Kg), N15017 (L, 4.1Kg)
Diagram Description: The K9 kit, when combined with other accessories like straps and luggage, allows for a maximum load capacity of 75 Kg on the vehicle's roof.
Diagram Description: A generic car with a roof rack system installed.
Installation Steps
Step 2.1: Component Orientation
Ensure the correct orientation of the fitting component. The diagram shows an incorrect (❌) and a correct (✔️) way to position the component.
Step 2.2: Initial Assembly
Attach component 40FE0249 (x4) using screw 62BB0800 (x4).
Step 2.3: Roof Bar Placement
Position the roof bars on the vehicle's roof rails. The diagram shows a top-down view of the car with arrows indicating placement. A measurement of approximately 70cm is shown between the bars.
Step 2.4: Alignment Check
Align the roof bars correctly. Diagrams show correct (✔️) and incorrect (❌) alignment relative to the car's width. Measurements in centimeters (cm) are shown for proper spacing.
Step 2.5: Securing the Bars
Secure the roof bars using the provided hardware. A hand is shown using tool 72FE0002 to tighten a screw, with indications for 'MAX x2' turns and a torque limit of 'MAX 4Nm'.
Step 2.6: Locking Mechanism
Engage and lock the fitting mechanism. Diagrams illustrate the correct (✔️) and incorrect (❌) operation of the locking system.
Maintenance and Checks
Warning: Regular checks are required after installation to ensure safety.
Perform pit-stop checks at the following intervals:
- 0100 Km: Pit-stop / Check!
- 0250 Km: Pit-stop / Check!
- 0500 Km: Pit-stop / Check!
Ensure all fasteners are tightened to the specified torque, with a maximum of 4Nm.
Company Information
Production Lot Information: The production lot number should be communicated for any spare parts.
NORDRIVE® is a registered trademark of LAMPA S.p.A.
Address: Via G. Rossa 53/55, 46019 Viadana (MN) ITALY
Contact: Tel. +39 0375 820700, service@lampa.it
LAMPA S.p.A. is a UNI EN ISO 9001:2015 Certified Company.
Websites: www.nordrive.it, www.lampa.it
