LOKITHOR JA301 PRO Jump Starter User Manual

1. Product Description

Main Buttons

1 - Power Button: Press briefly to turn on, press and hold for 2 seconds to turn off. In working mode, press to adjust display brightness.

2 - LED Light Button: Press to activate the LED light.

3 - Tire Pressure Preset Button: Set the desired tire pressure. The numbers will blink after setting the pressure. Blinking will stop upon completion. You can exit the setting mode. The display will show the real-time tire pressure.

4 - BAR/PSI Unit Switch: Press and hold for 5 seconds to switch to emergency start mode.

5 - Compressor On/Off Button: Press and hold for 3 seconds to turn on, press briefly to turn off.

Function Description

• 6 - Battery Indicator: Shows battery level.
• 7 - Digital Display Area: Displays various information.
• 8 - Voltage Indicator: Shows the voltage.
• 9 - Power Indicator: Indicates power status.
• 10 - Selected Pressure Unit (Bar/PSI): Shows the selected unit for tire pressure.
• 11 - Starting Indicator: Indicates the starting process.
• 12 - Positive Clamp Indicator: Green indicates a good connection, yellow indicates a poor connection.
• 13 - High Temperature Indicator: Lights up if the device is too hot.
• 14 - Low Temperature Indicator: Lights up if the device is too cold.
• 15 - Negative Clamp Indicator: Green indicates a good connection, yellow indicates a poor connection.
• 16 - Charging Indicator: Shows when the device is charging.
• 17 - Error Indicator: Lights up if there is an error.
• 18 - Reverse Connection Indicator: Lights up if the clamps are connected incorrectly.

Display Modes

a) Charging Display: Shows battery level and power status during charging.

b) Discharging Display: Shows battery level and discharge power when discharging via USB.

Input and Output Ports

1 - EC8 Output Port: For connecting jumper clamps.

2 - Charging and Discharging Port (USB-C): For charging the device and discharging power.

3 - Device Discharging Port (USB-A): For discharging power to devices.

4 - Compressor Output Port: For connecting the air hose.

2. Technical Specifications

Output

• USB-A: 5V/3A, 9V/2A, 12V/1.5A (max. 18W)
• USB-C: 5V/3A, 9V/3A, 12V/3A, 15V/3A, 20V/3A (max. 60W)

Input

• USB-C: 5V/3A, 9V/3A, 12V/3A, 15V/3A, 20V/3A (max. 60W)

LED Flashlight Brightness: 300 Lumens

Compressor Pressure: Max. 10 Bar (145 PSI)

3. Package Contents

• JA301 PRO Device
• Storage Bag for Accessories
• USB-C to USB-C Cable
• USB-C to USB-A Cable
• Set of Adapters for Compressor
• User Manual
• Storage Bag for Device
• Jumper Clamps
• Inflatable Hose for Compressor

4. Using the Device

A. Turning on the Device

Press the power button ? or the LED light button to activate the device.

B. Using the Device for Starting

Method 1: Normal Start

1. Ensure the vehicle's electrical system is 12V DC.
2. Connect the red (+) clamp to the positive (+) terminal of the car battery and the black (-) clamp to the negative (-) terminal. Ensure a secure connection.
3. Activate the device by briefly pressing the LED light button ? or the power button. A 10-second countdown will begin to check the clamp connection. If the indicator blinks after the countdown, the vehicle is ready to start.
4. Immediately after the vehicle starts, remove the clamps from the battery. Press and hold the power button for 2 seconds to turn off the device. If no operation is performed for 6 seconds, the device will automatically turn off.
5. If the vehicle does not start, check the clamp connections and try again. Do not attempt to start the vehicle more than 5 times within 15 minutes.

Method 2: Emergency Start

Safety Warning: Exercise extreme caution when using this mode. Ensure the (+) and (-) clamps do not touch each other to prevent electric shock, short circuits, device damage, battery damage, or fire.

1. If normal starting is unsuccessful (e.g., battery voltage is too low), you can use the emergency start function after carefully reading the manual.
2. Connect the jumper cable clamps to the EC8 connector on the device.
3. Connect the red (+) clamp to the positive (+) terminal of the car battery.
4. With the device on, press and hold the BAR/PSI button for 5 seconds to activate emergency start mode. The start indicator will light up, showing the clamps are active.
5. Connect the black (-) clamp to the negative (-) terminal of the car battery, ensuring a secure connection. The display will show the total voltage. You can now attempt to start the vehicle.
6. After a successful start, press the BAR/PSI or PUMP button to turn off.

Clamp Connection Status (Connect Max)

During the start mode, a 10-second countdown begins after connecting the clamps to check the battery and connection. If the connection impedance is low, the clamp status indicator will be green. If it's high, it will be yellow.

During the countdown, you can adjust the clamp connection. After 10 seconds, you must end the start mode and reconnect the clamps to measure the impedance again.

When the Lokithor is in forced start mode, the clamp status indicator will always blink yellow to warn of caution during use.

C. Using the Voltmeter

1. Connect the red (+) clamp to the positive (+) terminal of the car battery and the black (-) clamp to the negative (-) terminal, ensuring a correct connection.
2. After the 10-second interval, the status indicator on the main panel will light up, showing the current battery voltage.
3. After measurement, disconnect the clamps from the battery terminals.

4. Using the Device (Continued)

D. Using the Light

1. Press and hold the "LED Light" button ? for approximately 1 second to turn on the LED light.
2. Briefly press the "LED Light" button to cycle through modes: steady light, strobe, SOS, and off.
3. To turn off the device, press and hold the "LED Light" button for approximately 2 seconds.

E. Charging the Device

The device can be charged using:

• A) AC adapter (charger)
• B) USB-C to USB-C cable
• C) USB-A to USB-C cable

Connect the USB-C end of the cable to the device's charging port and the other end (USB-C or USB-A) to the charger.

The power indicator lighting up means the device is charging correctly.

If the battery indicator is yellow or red, charge the device immediately to prevent deep discharge. Do not leave the device in a discharged state for extended periods.

F. Charging a Mobile Phone via USB-A / USB-C

The device can charge mobile phones using USB-A / USB-C or USB-C / USB-C cables.

G. Using the Compressor

Attach the inflatable hose to the air compressor outlet, tighten the nut, and connect the other end to the tire valve.

Press the power button ? or the LED light button to activate the device.

Briefly press the BAR/PSI button to switch between tire pressure units: BAR, PSI.

Pressure Unit Conversion Table:

Note: Recommended tire pressure is usually indicated in Bar for vehicles.

To set the target tire pressure, first determine the desired pressure. The recommended (max) tire pressure can be found on the tire sidewall, vehicle sticker, or in the vehicle's manual. Adjust the target tire pressure using the "+"/"-" buttons. The set value will blink for 3 seconds, then the device will switch to real-time pressure monitoring mode.

Safety Warning: If the target pressure is not set and the air pump is turned on, it will not stop automatically. Manual shut-off is required. Failure to monitor tire pressure in real-time may lead to overinflation or tire damage.

Press and hold the "PUMP" button for 3 seconds to start the compressor. The compressor will automatically shut off when the tire pressure reaches the set value. To manually turn off the compressor, press the "PUMP" button or the power button ?.

Safety Warning: The product displays real-time tire pressure. A slight decrease in the displayed pressure after inflation is normal.

Remove the inflatable hose.

Safety Warning: The air compressor generates heat during inflation, causing the hose and all components to become hot. Allow the device to cool for 10 minutes before disconnecting the hose to prevent burns.

5. Error Codes

Error codes that may appear on the display:

6. Safety Precautions

Read the user manual carefully before using the device.

• No part of the device is user-replaceable. Never disassemble the device. Any intervention must be performed by a qualified service technician.
• Use the device only as instructed in the user manual. Improper use may cause serious electric shock.
• The device can only be used for starting vehicles with a 12V onboard voltage. It cannot be used for vehicles with a higher engine displacement or a voltage exceeding 12V.
• When using emergency start, exercise extreme caution. Ensure the (+) and (-) clamps do not touch each other to prevent short circuits. Ensure the clamps are securely connected to the battery terminals.
• To prolong the life of the internal battery, charge the device immediately after purchase. Charge the device regularly, at least every 3 months, to ensure sufficient power for future use. If the device is fully discharged or has low voltage, charge it immediately.
• Do not use the device if it is electrically damaged, dropped, or mechanically damaged.
• Never disassemble the device. Entrust any repairs, service, or maintenance to qualified service personnel.
• Do not use the device to start a vehicle while it is charging.
• Be careful not to drop metal objects onto the device display, as this could cause a short circuit, damage the device, or even cause an explosion.
• Ensure adequate ventilation when using the device for starting in an enclosed space.
• Keep sparks, electrical discharge, or open flames away from the device and the vehicle engine.
• To prevent short circuits and sparks from the device clamps, do not allow the (+) and (-) clamps to touch each other or any conductive material. Doing so can cause a short circuit, electric shock, or damage to the device.
• Use only the original clamps supplied with the device.
• Keep the device out of reach of children.
• Do not expose the device to rain, snow, or fire.
• Do not expose the device to extreme conditions (temperatures above +55°C, below -10°C, or humidity above 80%).
• Store the device in a cool, dry place, and use the protective case or box if necessary.

7. Preventive Measures and Further Instructions

• For use, the device must have at least 50% capacity. Insufficient power may prevent starting the vehicle.
• It is normal for the device to get warm during use.
• To ensure maximum device lifespan, charge the device regularly every 3 months.
• If liquid leaks from the device, or if a strange smell is detected when the device is turned on, do not use the device and refer it for inspection or repair to a professional workshop.
• Use only the original clamps (+) and (-) supplied with the package.
• Do not expose the device to direct sunlight.
• Do not disassemble or modify the device.
• Do not tamper with the device, press buttons forcefully, or move the device abruptly, as this may cause damage, short circuits, fire, or explosion.
• Do not use chemical cleaners or solvents to clean the device.

8. Device Recycling

• To prevent damage to the environment or human health, do not dispose of the device with regular household waste.
• Separate the device from other types of waste and recycle it responsibly to ensure sustainable use of materials. Utilize local collection points for electronics containing built-in batteries.

9. Warranty Conditions

In accordance with the provisions of § 2165 of the Civil Code (89/2012 Coll.), and Act No. 374/2022 Coll., the product is covered by a 24-month warranty against any material and workmanship defects.

Warranty claim conditions are as follows:

• The goods were submitted for warranty claim within 24 months of purchase.
• To claim, the buyer must present proof of purchase (receipt, invoice, etc.) from an authorized dealer.
• The warranty does not cover damage or malfunctions caused by normal wear and tear, physical damage, improper installation, incorrect use, modifications, or unauthorized repairs by third parties.
• The seller is not responsible for loss or damage caused during transport by a third party or due to force majeure.
• The seller is not responsible for any incidental or consequential damages resulting from the incorrect use of this product.
• All warranty claims are limited to the repair or replacement of defective products, and the assessment depends on the manufacturer/seller of the device.

Batteries, as a component of the product, are manufactured in accordance with the Regulation of the European Parliament and of the Council (EU) 2023/1542 on batteries and waste batteries.

CE