GZPFK-V1 TV Stand Assembly Instructions

Notice:

Follow the installation instructions. Please confirm all accessories are preset before installation.
Do not fully tighten the screws during initial assembly; fully tighten screws only once all pieces are assembled.
If you encounter any problems during installation, please contact customer service.

Parts List

Part 1: Top Panel - A large, rectangular panel with an angled front edge.
Part 2: Bottom Panel - A large, rectangular panel with an angled front edge and holes for feet.
Part 3: Left Side Panel - A tall, rectangular panel with an angled top edge.
Part 4: Right Side Panel - A tall, rectangular panel with an angled top edge, mirroring the left side panel.
Part 5: Middle Shelf - A rectangular shelf panel.
Part 6: Back Panel - A large rectangular panel, likely for the rear of the unit.
Part 7: Shelf - A rectangular shelf panel.
Part 8: Shelf - A rectangular shelf panel.
Part 9: Shelf - A rectangular shelf panel.
Part 10: Door (Left) - A decorative door panel with a cross pattern.
Part 11: Support Panel - Rectangular panels used for internal support.
Part 12: Door (Right) - A decorative door panel with a cross pattern, mirroring the left door.
Part 13: Door Panel - Decorative front panel for the doors.
Part 14: Front Support - A horizontal support beam.
Part 15: Front Support - A horizontal support beam.
Part 16: Side Support - A vertical support beam.
Part 17: Base Support - A horizontal support beam for the base.
Part 18: Door Hinge - Metal hinges for attaching doors.
Part 19: Top Cap/Accessory - A small component for the top surface, possibly for cable management.

Hardware List

A: M6x42 screws (22 PCS) - Long screws for structural connections.
B: Ø15x12 dowels/pins (22 PCS) - Cylindrical dowels for alignment and support.
C: M5x40 screws (28 PCS) - Medium-length screws.
D: M3.5x14 screws (22 PCS) - Short screws for smaller attachments.
E: Ø8x40 dowels/pins (8 PCS) - Longer dowels/pins.
F: M4x18 screws (4 PCS) - Short, thicker screws.
G: 220-96 cam locks (2 PCS) - Circular metal fasteners.
H: Cam lock bolts/posts (2 PCS) - Metal posts that screw into panels to mate with cam locks.
I: Ø4x63 dowels/pins (2 PCS) - Long, thin dowels/pins.
J: Ø6 dowels/pins (4 PCS) - Small, thin dowels/pins.
K: Feet/Legs (4 PCS) - Adjustable cylindrical feet.
L: Anti-tip kit (2 SET) - Safety hardware for securing to a wall.

Assembly Steps

Step 1

Attach the left side panel (3) and right side panel (4) to the bottom panel (2). Insert 4x dowels (B) into the pre-drilled holes on each side of the bottom panel (2). Align the side panels (3, 4) with the dowels and corresponding holes on the bottom panel (2). Secure each side panel to the bottom panel using 4x screws (C) inserted through the bottom panel into the side panels. Ensure the angled edges of the side panels face upwards and inwards. [Diagram shows 8x B dowels and 8x C screws used in this step.]

Step 2

Attach the middle shelf (5) and back panel (6) to the side panels (3, 4). Screw 4x cam lock bolts/posts (H) into the designated holes on the middle shelf (5). Insert 4x cam locks (G) into the corresponding holes on the inner faces of the side panels (3, 4). Align the middle shelf (5) with the side panels and secure by turning the cam locks (G) clockwise. Attach the back panel (6) to the side panels (3, 4) using 4x screws (D). [Diagram shows 4x H bolts, 4x G cam locks, and 4x D screws used in this step.]

Step 3

Attach the top panel (1) to the side panels (3, 4). Align the top panel (1) with the top edges of the side panels (3, 4). Secure using 10x screws (A) inserted from the top panel (1) into the side panels (3, 4). [Diagram shows 10x A screws used in this step.]

Step 4

Attach the shelves (7, 8) to the structure. Insert 4x dowels (B) into the pre-drilled holes on the inner faces of the side panels (3, 4) for shelf (7). Align shelf (7) with the dowels and secure using 4x screws (C) inserted through the side panels into the shelf. Repeat this process for shelf (8). [Diagram shows 8x B dowels and 8x C screws used in this step.]

Step 5

Attach the front supports (14, 15) and base support (17) to the bottom panel (2). Insert 2x dowels (B) into the ends of front support (14), 2x dowels (B) into front support (15), and 2x dowels (B) into base support (17). Align these supports with the corresponding holes on the bottom panel (2) and secure using 6x screws (B) inserted through the bottom panel into the supports. [Diagram shows 6x B dowels and 6x B screws used in this step.]

Step 6

Attach the side supports (16) to the front supports (14, 15) and base support (17). Insert 4x dowels (B) into the ends of the side supports (16). Align the side supports (16) with the front supports (14, 15) and base support (17) and secure using 4x screws (B). [Diagram shows 4x B dowels and 4x B screws used in this step.]

Step 7

Attach the top panel (1) to the structure. Insert 4x cam lock bolts/posts (H) into the designated holes on the top panel (1). Insert 4x cam locks (G) into the corresponding holes on the side panels (3, 4). Align the top panel (1) and secure by turning the cam locks (G) clockwise. [Diagram shows 4x H bolts and 4x G cam locks used in this step.]

Step 8

Attach the support panels (11) to the main structure. Insert 4x screws (C) through the pre-drilled holes on the support panels (11) into the side panels (3, 4). [Diagram shows 4x C screws used for each support panel, totaling 8x C screws.]

Step 9

Attach the shelves (7, 8) to the main structure. Insert 4x screws (C) through the pre-drilled holes on the shelves (7, 8) into the side panels (3, 4). [Diagram shows 4x C screws used for each shelf, totaling 8x C screws.]

Step 10

Attach the feet (K) to the bottom panel (2). Screw the 4x feet (K) into the threaded inserts on the underside of the bottom panel (2). [Diagram shows 4x K feet used in this step.]

Step 11

Attach the top panel (1) to the structure. Insert 4x screws (A) through the pre-drilled holes on the top edges of the side panels (3, 4) into the underside of the top panel (1). [Diagram shows 4x A screws used in this step.]

Step 12

Attach the base supports (14, 15, 17) to the main body. Insert 4x dowels (B) into the ends of the front supports (14, 15) and base support (17). Align these supports with the bottom panel (2) and secure using 8x screws (E) inserted through the bottom panel into the supports. [Diagram shows 4x B dowels and 8x E screws used in this step.]

Step 13

Attach the top cap/accessory (19) to the top panel (1). Align the top cap/accessory (19) with the designated holes on the top panel (1). Secure using 2x screws (D). [Diagram shows 2x D screws used in this step.]

Step 14

Attach the doors (10, 12) and door panels (13). Attach door hinges (18) to the doors (10, 12) using screws (D). Attach the door panels (13) to the doors (10, 12) using screws (F). Then, attach the doors (10, 12) to the side panels (3, 4) using the pre-attached hinges and screws (D). [Diagram shows 4x D screws for hinges, 4x F screws for door panels, and 4x D screws for attaching doors to side panels. Total: 8x D screws, 4x F screws.]

Step 15