Fantech Atmos Ceiling Fan

Product Identification

Models: ATMDCM - FAN MOTOR, ATMDC_BLADE - BLADE KIT, ATMDCLEDKIT - LED KIT* (*Optional Accessory)

Product Number: INST-ATM

Version: V1.0

Dimensional Drawings

The Atmos Ceiling Fan has the following dimensions:

Overall height: 530mm

Canopy height: 467mm

Blade span options: 1840mm/72", 2080mm/82", 2340mm/92"

Specifications

Safety Instructions

It is crucial to adhere to these Installation and Maintenance Instructions.

• All electrical installations must be performed by qualified and competent personnel according to statutory requirements.
• This appliance is not intended for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless supervised. Children should be supervised to ensure they do not play with the appliance.
• An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local wiring regulations.
• The fan must be mounted to a solid structure capable of supporting at least 60Kg.
• Fan blades must be installed at least 2.1m above the floor as per Australian regulations.
• Fan blades must be a minimum of 300mm from the nearest wall or permanent object.

WARNING: FOR SAFE USE OF THIS FAN, AN ALL-POLE DISCONNECTION MUST BE INCORPORATED INTO THE FIXED WIRING IN ACCORDANCE WITH THE WIRING RULES. Failure to do so may void the warranty.

A single-pole switch must also be placed in the same room as the fan as per local wiring regulations AS/NZS 3000.

Included in the Box

Before installation, verify all parts are included:

• 1. Mounting bracket
• 2. Canopy
• 3. Coupling cover
• 4. Top housing
• 5. Fan assembly with motor
• 6. Down rod
• 7. Mounting screw (4)
• 8. Motor screw (33, incl. spare)
• 9. Balancing kit
• 10. Remote with battery
• 11. Bottom cover
• 12. Blade* (8) (*Blades sold separately)

Installation

WARNING: Isolate the fan from the power supply before installation and maintenance. Inspect the fan for any damage upon receipt.

• The fan is suitable for ceiling mounting only. Ensure the installation location is adequately supported.
• Ensure the power supply matches the specifications. Incorrect power supply can damage the fan motor.
• Install the Mounting Bracket: Secure the bracket to the ceiling joist or similar structure. For timber frames, ensure wood screws are threaded at least 30mm into the support. The beam must be able to support up to 60Kg. (Note: Supplied screws are for timber structures only; use appropriate fasteners for other materials.)
• For angled ceilings, the fan hanging system supports a maximum mounting angle of 13 degrees. Ensure the mounting angle is less than this.
• Attach the Blades: Insert the blade through the slot on the motor housing and align blade holes with motor hub holes. Secure with 4 bolts. Do not overtighten. Repeat for all 8 blades.
• Install the Hub Cover: Place the cover over the motor hub, align holes, and secure with 4 screws.
• Install the Downrod: Remove the downrod ball from the downrod. Feed motor wiring through the downrod. Position the downrod over the motor shaft and insert bolts through matching holes. Secure with washers, nuts, and safety locking pins.
• Install Coupling Cover and Canopy: Slide the coupling cover onto the downrod, then the canopy. Re-install the downrod ball in its original position, ensuring it is secure.
• Hang the Fan Assembly: Lift the fan assembly onto the mounting bracket. Position the downrod ball so the notch rests over the pin on the mounting bracket to prevent rotation.
• After hanging and fitting blades, gently rotate the fan by hand to ensure it spins freely.
• Connect Wiring: Join the quick-connect wiring terminals between the fan assembly and mounting bracket, including the remote control unit, as per the wiring diagram.
• Fit Lower Cover/LED Diffuser: If installing the optional LED light kit, connect the LED plug to the motor hub plug. Secure the cover by locating it into position and rotating clockwise.
• Install Remote Receiver: Insert the remote receiver into the mounting bracket. Connect all quick-connect plugs between the bracket, receiver, and fan as per the wiring diagram.

Electrical Wiring Diagram

WARNING: All electrical connections must be fitted by a licensed Electrician.

Key for Wiring Diagram:

• A - Mains supply to receiver
• B - Receiver to motor plug
• C - Receiver to LED
• D - Motor plug connection

Wiring Steps:

• Connect mains power supply: Live to “L”, Neutral to “N”, Earth to "[earth symbol]" terminal. Ensure wires are secure and no bare wires are exposed.
• Insert the DC remote receiver into the mounting bracket.
• Connect the 3-port fixed wire quick connector (A) to the receiver power input socket.
• Connect the 3-port DC motor input wire connector (B) to the receiver motor power output socket.
• Connect the 2-port light wire connector (C) to the receiver light power output socket (omit if fan has no light).
• Join receiver output wire and motor power input wire using the 4-port quick connectors (D).

Remote Control Functions

Fan ON/OFF: Press once to turn the fan on/off. To pair the remote, press and hold for 5 seconds within 30 seconds of powering up the fan.

• Fan Speed Decrease: Press to reduce fan speed.
• Fan Speed Increase: Press to increase fan speed.
• Fan Turbo Speed Mode: Press to activate maximum fan speed.
• Forward/Reverse: Press to change fan direction. The fan will stop and then start in the opposite direction.
• Natural Wind Mode: Activates a mode that varies fan speed to simulate a breeze. Pressing any speed control button cancels this function.
• Light ON/OFF: Press to turn the light on/off. Press repeatedly within three seconds to cycle through light color temperature options.
• Light Brightness Increase: Press to increase light brightness.
• Light Brightness Decrease: Press to decrease light brightness.
• Timer Controls: Press increase/decrease buttons to activate. Press Fan ON/OFF to cancel.
• Delay ON Increase/Decrease: Adjusts the Delay On timer.
• Delay OFF Increase/Decrease: Adjusts the Delay OFF timer.
• LED Display: Shows fan speed (1-7) and time delay in hours (1-12).

Battery Installation

• Loosen the screw on the battery cover and remove it.
• Insert 2x AAA batteries, observing correct orientation.
• Replace and secure the battery cover. Remove batteries if the fan will not be used for an extended period.

Remote Bracket Installation

• Install the fan remote handset bracket on the wall as shown.

Remote Pairing

The remote and receiver are pre-paired. If a new remote is used or the fan is not responding correctly:

• Switch off the mains supply to the fan.
• Within 30 seconds of switching the mains supply back on, press and hold the Fan ON/OFF button for at least 5 seconds. An extended beep indicates successful pairing.
• Test the remote to confirm pairing.

Fan Movement and Noise

Ceiling fans may exhibit slight movement or 'wobble' during operation due to their mounting. Ensure all mounting screws and fasteners are tight and that rotating components are free of dust and build-up to minimize this.

Slight changes in motor noise may be noticeable in quiet spaces due to variations in electrical supply. This is normal and not a fault.

Fan Maintenance

• Inspect the fan every 12 months to ensure the motor, blades, and guards are clean. Remove dust and deposits with a non-abrasive cleaner.
• Check all fastenings for tightness. Check all rotating items.
• Bearings are 'sealed for life' and do not require detailed inspection.

Warranty

Scan the QR code or visit www.fantech.com.au/warranty for warranty information.

Contact Information:

• Website: www.fantechtrade.com.au, www.fantechtrade.co.nz
• Email: info@fantechtrade.com.au
• Australia: 1300 387 587
• New Zealand: 0800 106 266