EO MINI PRO 3 CUSTOMER CONNECTIVITY GUIDE

Table of Contents

Important: Read carefully before use. Keep for future reference.

1. Introduction
2. Check your firmware version
3. Instructions for Firmware 1.5.0 or Higher (ev.energy customers)
4. Network Setup (Choose your connection type)
5. Instructions for Firmware 1.4.5 or Earlier (e.g., 1.3.0, 1.3.5)
6. ev.energy support centre

1.0 Introduction

This guide will help you check, update, or change the network connection (Hardwired, Wi-Fi, or GSM) on your EO Mini Pro 3 charger.

Note: Updating or changing your connectivity options is only available for chargers connected via WiFi. To update or change your connection on Hardwired or GSM chargers, please contact ev.energy support. Please note however, changing these for any reason other than a hardware fault will not be covered by Warranty and therefore will come at cost.

1.1 What You Will Need

• A smartphone, tablet, or computer with Wi-Fi access
• Your EO Customer Card (provided at installation)
• Includes Serial Number, Hotspot Password, and Login Details
• Access to your charger and its upstream circuit breaker (RCD/MCB)

Note: If you can't find your customer card, please contact ev.energy support to request your login details.

2.0 Check Your Firmware Version

Your firmware version determines which instructions you need to follow.

If you're using the ev.energy app:

1. You are already on the latest firmware (1.5.0+). No need to check.

If you're using the EO Charging app:

1. Open the EO Charging app.
2. Go to Charge Point Diagnosis.
3. Note your firmware version (e.g., 1.3.0, 1.4.5, 1.5.0). See reference image below.

Image Description: A screenshot of the EO Charging app showing "Charge point diagnostics" with "V 1.5.0" displayed. It also shows "EO Device: EM301-DCL-PME", "Serial number: eo-000000000000000000", "OS: Android", "OS build: 15", and "Current device: samsung". There is a "Help & support" button.

4. Continue with the steps for your firmware version below.

3.0 Instructions for Firmware 1.5.0 or Higher (ev.energy Customers)

Note: Please read this entire instruction section before making any amends to the charger set up to ensure that no steps are missed.

Step 1: Power Cycle the Charger

1. Locate the RCD/MCB connected to your charger.
   Note: This will have been shown to you during the installation of the charger and can usually be located within the fuse box. It will resemble your other fuses within your fuse box but will be specific to your charger.
2. Switch it off, wait 10 seconds, then switch it on.
3. Wait 10-15 minutes to see if your charger appears in the ev.energy app. If the charger appears – you're all set! If not, proceed to Step 2.

Step 2: Connect to the Charger Hotspot

1. Power cycle the charger again (as in Step 1).
2. On your phone or computer, go to Wi-Fi Settings.
3. Look for a network with your charger serial number.
4. Connect to it using the Hotspot Password from your EO Customer Card.

Step 3: Log In to the Charger Portal

1. Open a web browser on your device.
2. Enter this address: https://10.10.10.1
3. Log in using your Customer Login details (these may be different to your hotspot password, please refer to the EO Customer Card for more information).
4. On the left menu, click Network.

4.0 Network Setup (Choose Your Connection Type)

Step 4A: (If Using a Hardwired Ethernet Connection)

Image Description: A screenshot of the EO Charging portal showing network settings. The "Ethernet" tab is selected. It displays "Status: up", "INET Address (IP/NETMASK): 192.168.0.156/24", "DNS Address: 192.168.0.1", "DHCP: Dynamic", and "Gateway Address: 192.168.0.1". There are "save" and "reload" buttons.

1. Confirm Ethernet status says “UP”.
2. Confirm the charger is connected to the ev.energy platform by following step 4D below.
3. If so, log out and wait 10 minutes.
4. Check the ev.energy app to confirm connection.

Note: If Ethernet status is Down/Red, contact ev.energy support for help.

Step 4B. If Using Wi-Fi

Image Description: A screenshot of the EO Charging portal showing Wi-Fi settings. It displays "WiFi Status: up: 33.8%". Below this are "Example Network Name @ 37%" and "Example Network Name 2 @ 21%". The "WiFi Mode" is set to "normal". "WiFi Enabled" is checked. "WiFi SSID" is set to "Example Network Name". "WiFi PSK" is hidden. "DHCP" is set to "Dynamic". "WiFi INET Address (IP/NETMASK)" is "dhcp". "WiFi DNS" and "WiFi Gateway" are not specified. There are "save", "save + connect wifi", and "save + connect adhoc" buttons.

1. Confirm the following:
   • Wi-Fi is enabled
   • SSID (Network Name) and Password (PSK) are filled in
   • Signal Strength is above 20%
2. Click Save,
3. Confirm the charger is connected to the ev.energy platform by following step 4D below, then Log out
4. Wait 10 minutes, then check the ev.energy app for connection

To change Wi-Fi network:

1. In the Network page, select a network from the list
2. Click "Use as Wi-Fi SSID"
3. Enter the Wi-Fi password (WiFi PSK)
4. Click "Save"
5. Confirm the charger is connected to the ev.energy platform by following step 4D below.
6. Log out
7. Wait 10 minutes, then check the app

Note: If no networks show up or all have signal below 10%, contact ev.energy support.

Step 4C. If Using GSM (Mobile SIM)

If your Mini Pro 3 is connected using GSM, please contact ev.energy support for assistance.

Step 4D. Final Check: Charger Page (For All Connection Types)

Image Description: A screenshot of the EO Charging portal showing "Charger Settings". It displays "Socket (Connector) #1/1" with "Cable Retainer" as "When ON the cable will be locked and can be left securely connected". Under "Charge Station Management System (CSMS)", it shows "Endpoint URL: wss://ocpp.ev.energy:443", "Identity: eo-021260097633201829", and "Connection Status: connected". There is a warning about advanced settings and a "confirm" button.

1. Navigate to the Charger page in the portal
2. Ensure Endpoint URL is set to: https://ocpp.ev.energy:443

Still not working? Please contact ev.energy support.

5.0 Instructions for Firmware 1.4.5 or Earlier (e.g., 1.3.0, 1.3.5)

1. Power cycle the charger (as in Step 2 above)
2. Wait 10-15 minutes and check:
   • ev.energy app
   • or EO Charging app

If your charger still does not appear, contact ev.energy support for assistance.

6.0 ev.energy Support Centre

Contact ev.energy support via the online chat or email below:

• Live support chat: https://support.ev.energy/en/support/home
• Email: support@ev.energy

If possible, please have your Customer Card or charger serial number ready when contacting us.