SAFETY INSTRUCTIONS
BEFORE ASSEMBLY
- Layout all components and hardware. Check all parts are included and undamaged.
- Anyone intending to install or use this monitor arm should read and understand this manual carefully.
WARNING
- This product contains small items that could be a choking hazard if swallowed.
- KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
- Improper installation, such as using the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. The manufacturer is not liable for any damage or injury caused by improper mounting or inappropriate use.
- If you do not understand these instructions or have any doubt about the safety instructions, assembly, or use of this product, please contact customer service.
Part List
- 1 Arm Set (x1)
- 2 Base (x1)
- 3 Vesa Plate (x1)
- 4 Plate (x1)
- 5 M8x150 Screw Bolt (x1)
TOOLS
- 6 5mm Allen Key (x1)
- 7 3mm Allen Key (x1)
VESA SCREWS
- A (x4) M4x12
- B (x4) M4x16
- C (x4) M5x12
- D (x4) M5x16
- E (x4) D5 Washer
- F (x4) D5 Plastic Spacer
ASSEMBLY STEPS
STEP 1: Mounting the Base
OPTION A: Clamp Installation
Illustration: Shows the base unit (2) with an Allen key (6) being used to adjust the clamp mechanism. Text indicates to adjust the clamp width to fit the desk.
Desk thickness compatibility: 0.4" ~ 1.97" (10 ~ 50mm).
Illustration: Shows the stand secured to the desktop by tightening the clamp with the Allen key (6).
OPTION B: Grommet Installation
Illustration: Shows the base unit (2) with a short bolt removed for clamp installation. A desk with a pre-drilled hole (diameter 0.4" - 2.4" / 10-60mm) is shown.
Ensure the desktop has a hole between 0.4" and 2.4" in diameter to use this option. Using an existing grommet hole is acceptable.
Illustration: Shows the long bolt (5) being inserted through the plate (4) and the desk hole. The Allen key (6) is used to tighten it. Desk thickness compatibility: 0.4" ~ 2.16" (10 ~ 55mm).
STEP 2: Arm Installation
Illustration: Shows the arm head being turned straight by hand.
Illustration: Shows the arm (1) being inserted into the base. The Allen key (7) is used to adjust a screw to fix the lower arm.
The screw is used to adjust the tightness of the connection between the base and the bracket arm to avoid the arms from shaking. ⚙️
STEP 3: Attach Monitor
OPTION A: Flat Back Monitor
Illustration: Shows the VESA plate (3) being attached to the back of a flat monitor. Screws and washers are used, tightened with the 5mm Allen Key (6).
Attach the VESA plate (3) to the back of the monitor and secure it by using the 5mm Allen Key (6) to tighten screws along with washers. ✔️
⚠️ Do not tighten the screws excessively or your monitor might be damaged.
OPTION B: Curved / Recessed Back Monitor
Illustration: Shows the VESA plate (3) being attached to the back of a curved monitor. Screws, washers, and plastic spacers (F) are used, tightened with the 5mm Allen Key (6).
Attach the VESA plate (3) to the back of the monitor and secure it by using the 5mm Allen Key (6) to tighten screws along with washers and spacers. ✔️
⚠️ Do not tighten the screws excessively or your monitor might be damaged.
STEP 4: Hang Monitor and Adjust Monitor Tilting Angle
Illustration: Shows a monitor being slid onto the head of the arm.
Slide the monitor onto the head of the arm.
⚠️ HEAVY! You may need assistance with this step.
Important Notice: The pressure of the gas spring is initially set to an intermediate value. So when the monitor hangs, make sure to hold it with both hands and don't let it drop suddenly. ⚠️
To remove the monitor: Push the lock plate (2) and lift the monitor (1) to separate it from the arm. ➡️
Illustration: Shows the tilt adjustment mechanism. The Allen key (6) is used to adjust a screw.
If the tilt adjustment mechanism is too tight or too loose, please adjust the screw as showed below:
- Turn clockwise to tighten ➕
- Turn counterclockwise to loosen ➖
STEP 5: Adjust Gas Spring Tension
For proper functioning of this mount, depending on the monitor's weight, you might need to adjust the tension in the upper arm (1).
Situation 1: Arm falls down
Upper Arm with monitor falls down and fails to stay where intended.
Illustration: Shows the arm falling. The Allen key (6) is used to adjust the gas spring tension screw.
Solution: Turn the inside screw counter-clockwise ("+" direction) to increase gas spring tension until the arm can stay as intended. ⬆️
Situation 2: Arm rises up / can't be pressed down
Upper Arm with monitor rises up automatically or can't be pressed down and fails to stay where intended.
Illustration: Shows the arm rising. The Allen key (6) is used to adjust the gas spring tension screw.
Solution: Turn the inside screw clockwise ("-" direction) to decrease gas spring tension until the arm can stay as intended. ⬇️
STEP 6: Cable Management
Remove Cable Cover
Illustration: Shows two keys being removed, followed by the cable cover.
Remove two keys first, then remove the cover.
Attach Cable Cover
Illustration: Shows the cable cover being inserted, followed by the installation of the two keys.
Insert the cover first, then install the two keys.
Adjust as Desired
Adjust monitor position and rotation.
- ✔️ Tilt
- ✔️ Swivel
- ✔️ Rotation
- ✔️ Height
Illustration: Shows a monitor mounted on the arm, with arrows indicating adjustable angles: Tilt (±90°), Swivel (±180°), Rotation (±180°), and Height adjustment (vertical arrows indicating range).
Note: To ensure stability, the tightness of the rotating axis has been pre-set, so it may be difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the two sides of it with both hands, and rotate vigorously. If that doesn't work out, please do not hesitate to ask for assistance.
WARNING: For your safety, do not move the stand off your desk! ⚠️
Product Dimensions
Illustration: A detailed diagram showing the monitor stand with various dimensions labeled, including arm extensions, VESA plate dimensions, and base dimensions. Example dimensions shown: min 9.88"~max 12.44" (arm extension), 8.19" (height), 1.5" (base width), min 0.4"~max 1.97" (clamp range), min 0.4"~max 2.16" (grommet range), min 6.1"~max 19.69" (height adjustment range).
CAUTION AND MAINTENANCE:
- Never allow children to climb, stand, hang, or play on any part of the monitor or stand.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
