INSTALLATION INSTRUCTION

Safety Caution

Please read this instruction carefully before installation.

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us.

⚠️ WARNING: This product contains small items that could be a choking hazard if swallowed. KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.

Hardware Included

All hardware is included in 01A.

• Clamp Bracket (01A): x1
• L Plate (01B): x1
• Round Plate (01C): x1
• Upper Pole (02A): x1
• Lower Pole (02B): x1
• Arm (03): x2
• 5mm Allen key: x1
• M8*10mm Screw: x4
• Cable Clip: x2
• Cable Clip: x2
• Monitor Kit (04):
  • Philips Screws M4 x 12mm (M-A): x16
  • Philips Screws M4 x 30mm (M-B): x16
  • Cap Nut (M-C): x4
  • Spacers L10mm (M-D): x32

Before Starting Assembly

Maximum load capacity: 17.6 LBS (8KG) per monitor. Compatible VESA patterns: 75x75mm, 100x100mm.

When attaching brackets to the flat screen, be careful not to over tighten screws and be sure that screws do not bottom out in the mounting holes.

Before starting assembly, verify all parts are included and undamaged. For parts shortage or damage, please contact us.

Visual guide for screw length: [Too Short] ❌, [Too Long] ❌, [Correct] ✔️, [Correct] ✔️.

Do not tighten the screws excessively or your monitor might be damaged.

Step 1A Clamp Installation

1. 1A-1: Prepare Clamp Bracket

   For desk plate thickness 10~51mm (0.39~2 inches).

   Secure the pole assembly with the preassembled screw (05A).

2. 1A-2: Prepare Clamp Bracket

   For desk plate thickness 51~80mm (2~3.15 inches).

   Assemble the upper pole (02A) and the lower pole (02B) together.

   Secure the L plate (01B) to the lower pole (02B) with the preassembled screws (05B).

   Secure the clamp bracket to the L plate (01B) with screws (06).

3. 1A-3: Final Clamp Assembly

   Adjust the clamp height to fit your desk plate. Secure the stand to the desktop by tightening the clamp.

Step 1B Grommet Base Installation

1. 1B-1: Prepare Grommet Base

   Assemble the upper pole (02A) and the lower pole (02B) together.

   Disassemble the clamp bracket. Marked parts [Part a] and [Part b] will be used in the next step.

2. 1B-2: Assemble Round Plate

   Assemble the round plate (01C) to the lower pole (02B) with the preassembled screws (05B).

   Dimensions for grommet hole: 10~40mm (0.39~1.57 inches) and 10~60mm (0.39~2.36 inches).

3. 1B-3: Mount to Desk

   Position the pole assembly on the desk. Secure it by tightening the knob bolt after passing the knob bolt [Part b] through the long plate [Part a], the desk hole, and the bottom of the pole assembly sequentially.

Step 2 Attach the VESA plates to the monitors

(a) For Flat Back Monitors

Attach VESA plates using M4 x 12mm screws (M-A).

(b) For Recessed / Curved Back Monitors

Attach VESA plates using M4 x 30mm screws (M-B). Note: Use 1 piece or 2 pieces of spacers (M-D) as needed.

Step 3 Assemble the stand

Assemble the monitor arms (03) and the pole together.

Ensure bolt heads are facing UP (⬆️ Bolt Heads UP!).

Fasten the bolt with the 5mm Allen key (05C). Attach the cable clips (07A and 07B) to the stand.

Step 4 Attach the monitors to the stand

Hang the monitor onto the arm. Use safety screws [L] / cap nuts (M-C) to secure the monitors.

Attach the cap nut to the safety screw.

Hang the monitors onto the monitor arm (03) then using the 3mm Allen key (05B) to turn the screws [L] to adjust the monitors to the same level if necessary.

Monitor arm should be placed with screw facing backwards.

⚠️ WARNING: Hang 2 monitors onto the same arm at the same time to prevent the stand falling.

Actions: [Rise monitor], [Lower monitor].

Step 5 Tilting Adjustment

Loosen the tilting bolts, pull the monitor to your desired angle, then fasten the tilting bolts with the 5mm Allen key (05C).

Adjustment range: -90° to +90°.

Step 6 Switch screen horizontally and vertically

If needed, the monitor can be rotated ±90 degrees for switching screen between horizontally and vertically.

360° Rotation

This function works better for monitors with the center of gravity. Note: To ensure stability, the tightness of the rotation axis is preset, so it needs some effort to rotate the VESA Plate.

Suggestion: For initial rotation, attach the monitor first, then hold both sides and rotate firmly. If resistance is met, contact Amazon customer support.

Manage tools and cables

This cable clip also can take in the Allen keys.

Set the desired angle of the monitors

[Desk] [Desk]

Product dimensions

Overall Height: 31.73" (806mm)

Arm Span: 30" (762mm)

Vertical Pole Height: 0.39~3.15" (10~80mm)

Other dimensions indicated in diagrams: 1.54" (39mm), 7.29" (185.3mm), 6.18" (157mm), 2.95" (75mm), 3.94" (100mm).